Over the past few years, researchers have directed a significant amount of effort towards realizing tunable all-optical devices using nonlinear optical methods. It is now possible to exercise dynamic control of the group velocity of light traveling through a wide variety of material systems. The slow and fast light refer to situations in which the group velocity íg of an optical pulse through a dispersive material can be made to be smaller and larger, respectively, than the phase velocity vp = c/n. This ability could overcome the remaining challenge in current optical networks of storing and manipulating an optical signal directly in optical domain so as to avoid a bottleneck due to optical-to-electrical (O/E) and electrical-to-optical (E/O) conversions. The overall purpose of the dissertation is to study novel slow-light systems that provide controlled generation of large pulse delays relative to the pulse width with minimal pulse shape distortion by optimally design resonance profiles of such systems. The system design studies utilize several measures of performance such as the fractional delay, power throughput, and signal distortion under the limited system resource constraints. To this end, powerful data fidelity metrics are required to quantify the performance of tunable delay devices. Here, a new framework for measuring an information velocity and throughput is described and implemented using Shannon mutual information concepts. This new technique is used to investigate trends, trade-offs, and limits in slow light devices, which are physically sensible and in good agreement with analyses obtained using a conventional eye-opening(EO) metric. Using these information-theoretic and/or conventional metrics, we present the quantifying performance of gain-based stimulated Brillouin scattering (SBS) system in optical fibers as well as optical passive devices such as Fabry-Perot, fiber Bragg gratings, and ring resonators. It is shown that combining the SBS gain medium with these passive devices can compensate their respective disadvantages and thus increase delay performance without using additional resource of SBS pump power. The results show the possibility of achieving a fractional delay up to 10 at a signal bandwidth up to tens of GHz.
Over the past few years, researchers have directed a significant amount of effort towards realizing tunable all-optical devices using nonlinear optical methods. It is now possible to exercise dynamic control of the group velocity of light traveling through a wide variety of material systems. The slow and fast light refer to situations in which the group velocity íg of an optical pulse through a dispersive material can be made to be smaller and larger, respectively, than the phase velocity vp = c/n. This ability could overcome the remaining challenge in current optical networks of storing and manipulating an optical signal directly in optical domain so as to avoid a bottleneck due to optical-to-electrical (O/E) and electrical-to-optical (E/O) conversions. The overall purpose of the dissertation is to study novel slow-light systems that provide controlled generation of large pulse delays relative to the pulse width with minimal pulse shape distortion by optimally design resonance profiles of such systems. The system design studies utilize several measures of performance such as the fractional delay, power throughput, and signal distortion under the limited system resource constraints. To this end, powerful data fidelity metrics are required to quantify the performance of tunable delay devices. Here, a new framework for measuring an information velocity and throughput is described and implemented using Shannon mutual information concepts. This new technique is used to investigate trends, trade-offs, and limits in slow light devices, which are physically sensible and in good agreement with analyses obtained using a conventional eye-opening(EO) metric. Using these information-theoretic and/or conventional metrics, we present the quantifying performance of gain-based stimulated Brillouin scattering (SBS) system in optical fibers as well as optical passive devices such as Fabry-Perot, fiber Bragg gratings, and ring resonators. It is shown that combining the SBS gain medium with these passive devices can compensate their respective disadvantages and thus increase delay performance without using additional resource of SBS pump power. The results show the possibility of achieving a fractional delay up to 10 at a signal bandwidth up to tens of GHz.
We use an information-theoretic method developed by Neifeld and Lee [J. Opt. Soc. Am. A 25, C31 (2008)] to analyze the performance of a slow-light system. Slow-light is realized in this system via stimulated Brillouin scattering in a 2 km-long, room-temperature, highly nonlinear fiber pumped by a laser whose spectrum is tailored and broadened to 5 GHz. We compute the information throughput (IT), which quantifies the fraction of information transferred from the source to the receiver and the information delay (ID), which quantifies the delay of a data stream at which the information transfer is largest, for a range of experimental parameters. We also measure the eye-opening (EO) and signal-to-noise ratio (SNR) of the transmitted data stream and find that they scale in a similar fashion to the information-theoretic method. Our experimental findings are compared to a model of the slow-light system that accounts for all pertinent noise sources in the system as well as data-pulse distortion due to the filtering effect of the SBS process. The agreement between our observations and the predictions of our model is very good. Furthermore, we compare measurements of the IT for an optimal flattop gain profile and for a Gaussian-shaped gain profile. For a given pump-beam power, we find that the optimal profile gives a 36% larger ID and somewhat higher IT compared to the Gaussian profile. Specifically, the optimal (Gaussian) profile produces a fractional slow-light ID of 0.94 (0.69) and an IT of 0.86 (0.86) at a pump-beam power of 450 mW and a data rate of 2.5 Gbps. Thus, the optimal profile better utilizes the available pump-beam power, which is often a valuable resource in a system design.
Dynamic control of the speed of a light signal, based on stimulated Brillouin scattering in optical fibers, was theoretically studied and also experimentally demonstrated as the core object of this thesis. To date, slow light based on stimulated Brillouin scattering has shown the unmatched flexibility to offer an efficient timing tool for the development of all-optical future router. Nevertheless, the seeming perfect Brillouin slow light suffered from three major obstacles: naturally narrow signal bandwidth, strong change of signal amplitude, and significant signal distortion. The essential contribution of this work has been mostly dedicated to resolve all those impairments so as to make Brillouin slow light a completely operating all-optical delay line for practical applications. Actually, high capability of tailoring the spectral distribution of the effective Brillouin resonance makes possible to resolve partially or completely all those problems. First of all, a broadband spectral window was passively obtained in between two Brillouin gain/loss resonances by simply appending two segments of fibers showing different Brillouin frequency shifts. The global Brillouin gain of the concatenated fibers manifests a gain/loss doublet resonance showing a broad window in between gain/loss peaks. In practice, this configuration has a crucial advantage that it removes the need of the pump modulation, generally used to create a polychromatic pump source. Therefore, a broadband Brillouin slow and fast light was simple realized with a reduced distortion. Secondly, the signal amplification or attenuation associated to the signal delay was completely compensated by superposing Brillouin gain and loss resonances with identical depth but different width. As a result, the Brillouin gain led to effectively a spectral hole in the center of the broadband absorption and opened a transparent window while the sharp change in the refractive index was preserve. This way it makes possible to realize zero-gain Brillouin slow light. This configuration was also exploited to produce Brillouin fast light with a total absence of signal loss, simply by swapping the spectral position of the two pumps. At last, a signal was continuously delayed through a Brillouin fiber delay line without any distortion. Due to the strong induced dispersion, pulse broadening is a major difficulty in all slow light systems and it is impossible to compensate such broadening using a linear system. Therefore, a conventional Brillouin slow light system was combined with a nonlinear optical fiber loop mirror that gives a nonlinear quadratic transmission. Using this configuration, the inevitable pulse broadening was completely compensated at the output of the loop and a signal was delayed up to one symbol without any distortion. Brillouin slow light systems were further studied in the spectral domain. For a given Brillouin resonance the spectrum of a light pulse was optimized to better match the Brillouin bandwidth. When the time envelope of a pulse was properly shaped, it was clearly observed that the spectral width of the pulse became minimized while preserving the pulse duration. This way the maximum time delay through Brillouin slow light could be enhanced for a fixed pulse width. Brillouin fast light was even realized in total absence of any pump source, which is a plain requirement for the generation of Brillouin slow or fast light. This self-generated delay line, key contribution of this thesis, relies on both spontaneous and stimulated Brillouin scattering in optical fibers. In this implementation, a light signal was strongly boosted above the so-called Brillouin threshold, so that most power of the signal was transferred to a backward propagating wave, namely the generation of amplified spontaneous Stokes wave. Since the center frequency of the intense Stokes wave is below the signal frequency by exactly Brillouin shift of the fiber used, this wave led to a Brillouin loss band centered at the signal frequency. Consequently, the signal experienced fast light propagation and the propagation velocity of the signal was self-controlled, simply by varying the signal input power. This technique has many practical advantages such as its high simplicity of the configuration and an invariant signal power in the output of this delay line. Additionally, this system self-adapts the signal bandwidth as the spectrum of the amplified Stokes wave matches the spectral distribution of the signal. An alternative method to generate all-optical delay line was proposed instead of slow light. This scheme makes use of the combination of wavelength conversion and group velocity dispersion. This type of delay line was mainly aimed at improving the storage capability of delaying element. The wavelength of a signal was simply and efficiently converted at a desired wavelength using cross gain modulation in semiconductor optical amplifiers. Then the converted signal was delivered to a high dispersive medium and arrived at the end of the medium with relative time delay due to the group velocity dispersion. A fractional delay of 140 was continuously produced through this delay line for a signal with a duration of 100 ps, preserving signal bandwidth and wavelength. The effect of slow light on linear interactions between light and matter was experimentally investigated to clarify the current scientific argument regarding slow light-enhanced Beer-Lambert absorption. It was predicted that real slowing of the light group velocity could enhance the molecular linear absorptions so as to improve the sensitivity of this type of sensing. However, the experimental results unambiguously show that material slow light (slow light in traveling wave media) does not enhance the Beer-Lambert absorption.
High-speed optical networks will require all-optical signalprocessing to avoid bottleneck due to optical-to-electrical (O/E)and electrical-to-optical (E/O) conversion. Enabling of opticalprocessing tasks such as optical buffering and data synchronizationwill require large tunable delay. Recently, slow-light physics gotwide attention to generate tunable delay. However, for a slow-lightsystem large delay comes at the expense of increased distortion.This dissertation presents a study of the slow-light systems andquantifies the limitations imposed on delay due to distortion andsystem resource constraints. Optimal designs for two- and three-lineBrillouin slow-light systems showed fractional pulse delay of up to1.7 compared to a single-line gain system. Optimal designs forbroadband Brillouin gain system showed upto 100\% delay improvementcompared to the Gaussian pump. Wavelength conversion and dispersionbased tunable delay systems showed bit delay of 15 bits. An opticalbuffer based on photorefractive medium for real-time data storagewas demonstrated by storing and retrieving a 7-bit data sequence.
The manipulation of the group velocity of optical signals (slow and fast light) has many possible applications in telecommunications, sensing, nonlinear optics, and so on. The exploitation of the effect of stimulated Brillouin scattering (SBS) is of special interest for the alteration of the group velocity in optical fibers, since it just requires standard telecom equipment and low-to-moderate optical power. However, each delay in one single, low-gain SBS-based slow-light system is accompanied by a pulse broadening. This is a result of the inherent Kramers–Kronig relations among the gain, the phase change, and the accompanied group velocity. For an ideal flat gain, the phase change is nonideal, and for an ideal phase change the gain curve leads to a broadening. Furthermore, if the gain bandwidth is adapted to the signal by broadening, the delay will be reduced. Thus the signal broadening can be reduced by several methods for one single low-gain slow-light system, but it cannot be zero. Here, we will show how a zero-broadening SBS-based slow light can be achieved with several methods. The basic idea is a reshaping of the original pulse in a second stage by saturation of the SBS system, or by the superposition of two gains. As will be shown, all of these systems show an almost ideal overall gain and phase function over the bandwidth of the pulses. Thus, SBS-based slow light with a delay bandwidth product of 1 bit and zero distortion is possible.
Frontiers in Guided Wave Optics and Optoelectronics 84 absorption is much too high to render the group effect useful.An exciting breakthrough happened in the early nineties when it was shown that group velocities of few tens of meters per second were possible with nonlinear resonance interactions (Hau et al., 1999).Two important features of nonlinear resonances make this possible: substantially reduced absorption, or even amplification, of radiation at a resonance, and sharpness of such resonances; the sharper a resonance, the higher dn/dω and so the stronger the enhancement of group index, and hence the greater the pulse is delayed.Widely ranging applications for slow light have been proposed, of which those for telecommunication systems and devices (optical delay lines, optical buffers, optical equalizers and signal processors) are currently of most interest (Gauthier, 2005).The essential demand of such devices is compatibility with existing telecommunication systems, that is they must be of wide enough bandwidth (≥10 GHz) and able to be integrated seamlessly into such systems.Of the various nonlinear resonance mechanisms and media, which allow sufficiently long induced delays, stimulated Brillouin and Raman scattering (SBS and SRS) in optical fiber are deemed to be among the best candidates.Currently SBS is the most actively investigated and many experimental and theoretical papers on pulse delaying via SBS in optical fiber have been published in the last few years, see the review paper (Thevenaz, 2008) and references therein.In this process the pulse to be delayed is a frequency down-shifted (Stokes) pulse.This is transmitted through an optical fiber through which continuous wave (CW) pump radiation is sent in the opposite direction to prime the delay process.It is supposed that the Stokes pulse is amplified by parametric coupling with the pump wave and a material (acoustic) wave in the medium (Kroll, 1965), and the amplification is characterised by a resonant-type gain profile.The dispersion of refractive index associated with this profile (which is similar to that in Fig. 1) can then be used to increase the group index for optical pulses at the Stokes frequency (Zeldovich, 1972).Along with obvious device compatibility, there are several other advantages of the SL via SBS approach for optical communications systems: slow-light resonance can be created at any wavelength by changing the pump wavelength; use of optical fibre allows for long interaction lengths and thus low powers for the pump radiation, the process runs at room temperature, it uses off the shelf telecom equipment, and SBS works in the entire transparency range of fibers and in all types of fiber.Currently a main obstacle to applications of this approach is the narrow SBS gain spectral bandwidth, (Thevenaz, 2008), which is typically ≈ 120-200 MHz in silica fiber in the spectral range of telecom optical radiation (~1.3-1.6 μm) (Agrawal, 2006).This chapter reviews our ongoing work on the physical mechanisms that give rise to pulse delay in SBS.In section 2 the theoretical background of the SBS phenomenon is given and the main working equations describing this nonlinear interaction are presented.In section 3 ways by which the SBS spectral bandwidth may be increased are addressed.Waveguide induced spectral broadening of SBS in optical fibre is considered as a means of increasing the bandwidth to the multi-GHz range.An alternative way widely discussed in the literature, (Thevenaz, 2008), is based on spectral broadening of the pump radiation.However it is shown through analytic analysis of the SBS equations converted to the frequency domain that pump radiation broadening by any reasonable amount has only a negligible effect on increasing the SBS bandwidth.Importantly in this section we show that, irrespective of the nature of the broadening considered, the SBS gain bandwidth remains www.intechopen.
This Thesis lies within the field of Slow and Fast Light (SFL) technologies, which are currently receiving much attention because of their interesting applications, ranging from optical information processing to enhanced precision sensing and interferometry. These technologies are based on systems that exhibit steep positive dispersion to propagate a light pulse at group velocity well below the speed of light in vacuum (slow light) or steep negative dispersion to achieve pulse propagation at superluminal or even at negative group velocity (fast light). SFL effects thus arise in a myriad of materials exhibiting spectral resonances. Current efforts in this field are mainly focused on the manipulation of material gain or absorption resonances by nonlinear optical processes (material SFL) or on the optimization of photonic band-gap structures, without substantial material dispersion, but where structural dispersion comes as a result of the coupling between the light wavelength and the characteristic length of the system (structural SFL). This Thesis focuses on the theoretical and experimental analysis of electromagnetic pulse propagation with abnormal group velocities in two kind of linear and passive devices. In the first part of the Thesis a new system exhibiting structural SFL is demonstrated. It deals with multiple-beam interferometers and provides a comprehensive study of the arising of SFL in this system devoid of photonic band gaps. A theoretical model that fully describes the allowed pulse propagation regimes and its performance in terms of both the interferometer's and the pulse characteristics is developed. Considering amplitude modulated pulses, the capabilities and limitations of SFL effects in this kind of system are retrieved by quantifying typical figures of merit like fractional delay, pulse distortion and Delay-Bandwidth Product. The theoretical framework is valid for any frequency region and the model predictions are probed by performing experiments in the radiofrequency range and through exact numerical simulations in the optical range. The simplest interferometer, with only two branches, is first considered since it is widely used in actual communication systems. It is analytically demonstrated that slow light cannot possibly be sustained and that the total attenuation drives the changes in the pulse propagation regimes. By increasing the number of branches, group delay tuning from slow to fast light regimes occurs if the optical length of one of the branches is slightly changed. In the second part of the Thesis, the ability of mono- and multilayer structures to speed up or slow down electromagnetic pulses is investigated, with special emphasis on their reflection properties. Namely, Distributed Bragg Reflectors (DBRs) and Fabry-Perot filters, common in today's communication systems, are examined. These structures were fabricated to operate in the microwave and in the radiofrequency range with the aim of confirming theoretical predictions. Experimental results of their frequency- and time-domain characterization are compared with simulations. An advantage of operating in these frequency ranges is that the transmission and reflection phase function can be measured with a two port vector network analyzer. Such a simple measurement of this key function that determines the pulse propagation regime cannot be directly performed in the optical range. Moreover, microstrip DBRs were designed and their potential application as a negative group-delay circuit to improve the efficiency of feedforward amplifiers, which are commonly used for cancelling inherent distortion in microwave amplifiers, is explored.