Frontiers in Guided Wave Optics and Optoelectronics 84 absorption is much too high to render the group effect useful.An exciting breakthrough happened in the early nineties when it was shown that group velocities of few tens of meters per second were possible with nonlinear resonance interactions (Hau et al., 1999).Two important features of nonlinear resonances make this possible: substantially reduced absorption, or even amplification, of radiation at a resonance, and sharpness of such resonances; the sharper a resonance, the higher dn/dω and so the stronger the enhancement of group index, and hence the greater the pulse is delayed.Widely ranging applications for slow light have been proposed, of which those for telecommunication systems and devices (optical delay lines, optical buffers, optical equalizers and signal processors) are currently of most interest (Gauthier, 2005).The essential demand of such devices is compatibility with existing telecommunication systems, that is they must be of wide enough bandwidth (≥10 GHz) and able to be integrated seamlessly into such systems.Of the various nonlinear resonance mechanisms and media, which allow sufficiently long induced delays, stimulated Brillouin and Raman scattering (SBS and SRS) in optical fiber are deemed to be among the best candidates.Currently SBS is the most actively investigated and many experimental and theoretical papers on pulse delaying via SBS in optical fiber have been published in the last few years, see the review paper (Thevenaz, 2008) and references therein.In this process the pulse to be delayed is a frequency down-shifted (Stokes) pulse.This is transmitted through an optical fiber through which continuous wave (CW) pump radiation is sent in the opposite direction to prime the delay process.It is supposed that the Stokes pulse is amplified by parametric coupling with the pump wave and a material (acoustic) wave in the medium (Kroll, 1965), and the amplification is characterised by a resonant-type gain profile.The dispersion of refractive index associated with this profile (which is similar to that in Fig. 1) can then be used to increase the group index for optical pulses at the Stokes frequency (Zeldovich, 1972).Along with obvious device compatibility, there are several other advantages of the SL via SBS approach for optical communications systems: slow-light resonance can be created at any wavelength by changing the pump wavelength; use of optical fibre allows for long interaction lengths and thus low powers for the pump radiation, the process runs at room temperature, it uses off the shelf telecom equipment, and SBS works in the entire transparency range of fibers and in all types of fiber.Currently a main obstacle to applications of this approach is the narrow SBS gain spectral bandwidth, (Thevenaz, 2008), which is typically ≈ 120-200 MHz in silica fiber in the spectral range of telecom optical radiation (~1.3-1.6 μm) (Agrawal, 2006).This chapter reviews our ongoing work on the physical mechanisms that give rise to pulse delay in SBS.In section 2 the theoretical background of the SBS phenomenon is given and the main working equations describing this nonlinear interaction are presented.In section 3 ways by which the SBS spectral bandwidth may be increased are addressed.Waveguide induced spectral broadening of SBS in optical fibre is considered as a means of increasing the bandwidth to the multi-GHz range.An alternative way widely discussed in the literature, (Thevenaz, 2008), is based on spectral broadening of the pump radiation.However it is shown through analytic analysis of the SBS equations converted to the frequency domain that pump radiation broadening by any reasonable amount has only a negligible effect on increasing the SBS bandwidth.Importantly in this section we show that, irrespective of the nature of the broadening considered, the SBS gain bandwidth remains www.intechopen.
Frontiers in Guided Wave Optics and Optoelectronics 84 absorption is much too high to render the group effect useful.An exciting breakthrough happened in the early nineties when it was shown that group velocities of few tens of meters per second were possible with nonlinear resonance interactions (Hau et al., 1999).Two important features of nonlinear resonances make this possible: substantially reduced absorption, or even amplification, of radiation at a resonance, and sharpness of such resonances; the sharper a resonance, the higher dn/dω and so the stronger the enhancement of group index, and hence the greater the pulse is delayed.Widely ranging applications for slow light have been proposed, of which those for telecommunication systems and devices (optical delay lines, optical buffers, optical equalizers and signal processors) are currently of most interest (Gauthier, 2005).The essential demand of such devices is compatibility with existing telecommunication systems, that is they must be of wide enough bandwidth (≥10 GHz) and able to be integrated seamlessly into such systems.Of the various nonlinear resonance mechanisms and media, which allow sufficiently long induced delays, stimulated Brillouin and Raman scattering (SBS and SRS) in optical fiber are deemed to be among the best candidates.Currently SBS is the most actively investigated and many experimental and theoretical papers on pulse delaying via SBS in optical fiber have been published in the last few years, see the review paper (Thevenaz, 2008) and references therein.In this process the pulse to be delayed is a frequency down-shifted (Stokes) pulse.This is transmitted through an optical fiber through which continuous wave (CW) pump radiation is sent in the opposite direction to prime the delay process.It is supposed that the Stokes pulse is amplified by parametric coupling with the pump wave and a material (acoustic) wave in the medium (Kroll, 1965), and the amplification is characterised by a resonant-type gain profile.The dispersion of refractive index associated with this profile (which is similar to that in Fig. 1) can then be used to increase the group index for optical pulses at the Stokes frequency (Zeldovich, 1972).Along with obvious device compatibility, there are several other advantages of the SL via SBS approach for optical communications systems: slow-light resonance can be created at any wavelength by changing the pump wavelength; use of optical fibre allows for long interaction lengths and thus low powers for the pump radiation, the process runs at room temperature, it uses off the shelf telecom equipment, and SBS works in the entire transparency range of fibers and in all types of fiber.Currently a main obstacle to applications of this approach is the narrow SBS gain spectral bandwidth, (Thevenaz, 2008), which is typically ≈ 120-200 MHz in silica fiber in the spectral range of telecom optical radiation (~1.3-1.6 μm) (Agrawal, 2006).This chapter reviews our ongoing work on the physical mechanisms that give rise to pulse delay in SBS.In section 2 the theoretical background of the SBS phenomenon is given and the main working equations describing this nonlinear interaction are presented.In section 3 ways by which the SBS spectral bandwidth may be increased are addressed.Waveguide induced spectral broadening of SBS in optical fibre is considered as a means of increasing the bandwidth to the multi-GHz range.An alternative way widely discussed in the literature, (Thevenaz, 2008), is based on spectral broadening of the pump radiation.However it is shown through analytic analysis of the SBS equations converted to the frequency domain that pump radiation broadening by any reasonable amount has only a negligible effect on increasing the SBS bandwidth.Importantly in this section we show that, irrespective of the nature of the broadening considered, the SBS gain bandwidth remains www.intechopen.
The manipulation of the group velocity of optical signals (slow and fast light) has many possible applications in telecommunications, sensing, nonlinear optics, and so on. The exploitation of the effect of stimulated Brillouin scattering (SBS) is of special interest for the alteration of the group velocity in optical fibers, since it just requires standard telecom equipment and low-to-moderate optical power. However, each delay in one single, low-gain SBS-based slow-light system is accompanied by a pulse broadening. This is a result of the inherent Kramers–Kronig relations among the gain, the phase change, and the accompanied group velocity. For an ideal flat gain, the phase change is nonideal, and for an ideal phase change the gain curve leads to a broadening. Furthermore, if the gain bandwidth is adapted to the signal by broadening, the delay will be reduced. Thus the signal broadening can be reduced by several methods for one single low-gain slow-light system, but it cannot be zero. Here, we will show how a zero-broadening SBS-based slow light can be achieved with several methods. The basic idea is a reshaping of the original pulse in a second stage by saturation of the SBS system, or by the superposition of two gains. As will be shown, all of these systems show an almost ideal overall gain and phase function over the bandwidth of the pulses. Thus, SBS-based slow light with a delay bandwidth product of 1 bit and zero distortion is possible.
The group velocity at which light pulses propagate through a dispersive material system is very different from the vacuum speed of light c, One refers to light as being "slow" for v g << c (Boyd & Gauthier, 2009) or "fast" for v g > c or v g <0 (Stenner et al, 2003 ).For v g <0, the pulse envelope appears to travel backward in the material (Gehring et al, 2006), and hence it is sometimes referred to as "backward light."The subject of slow light has caused keen interest in the past decade or more, and it is possible to control the group velocity of light pulses in the dispersive materials.Interest in slow and fast light dates back to the early days of the 20th century.Sommerfeld and Brillouin (Sommerfeld & Brillouin, 1960) were intrigued by the fact that theory predicts that v g can exceed c, which leads to apparent inconsistencies with Einstein's special theory of relativity.Experimental investigations of extreme propagation velocities were performed soon after the invention of the laser (Faxvog and et al, 1970).In 1999, Harris's group research work greatly stimulated researchers' interests, which showed that light could be slowed down to 17m/s.The result was obtained in ultra cold atom clouds with the use of electromagnetically induced transparency (EIT), which induces transparency in a material while allowing it to retain strong linear and nonlinear optical properties (Hau et al, 1999).Slow light can also be obtained through the use of the optical response of hot atomic vapors (Philips et al, 2001).These early research works require hard conditions and the slow light cannot operate in room temperature.Recently, researchers found ways to realize slow light operating in room temperature and solid-state materials, which are more suited for many practical applications, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.In this chapter, we describe some of the physical mechanisms that can be used to induce slow and fast light effects in room-temperature solids (Bigelow et al, 2003) and some of the exotic propagation effects that can thereby be observed.We also survey some applications of slow and fast light within the fields of quantum electronics and photonics. Fundamentals of slow and fast lightSlow and fast light refer to the group velocity of a light wave.The group velocity is the velocity most closely related to the velocity at which the peak of a light pulse moves through an optical dispersive material (Milonni, 2005), and is given by the standard result www.intechopen.comRecent Progress in Optical Fiber Research 82where n is the refractive (phase) index and ω is the angular frequency of the carrier wave of the light field.One refers to light as being slow light for v g << c, fast light for for v g > c, and backwards light for v g <0 or v g is negative.Extreme values of the group velocity invariably rely on the dominance of the second contribution to the group index of Equation ( 1).This contribution of course results from the frequency dependence of the refractive index, and for this reason extreme values of the group velocity are usually associated with the resonant or near-resonant response of material systems.According to this theory, slow light is expected in the wings of an absorption line and fast light is expected near line center, and the spatial dispersion, that is, the non-locality in space of the medium response, is another mechanism that can lead to slow light, as has been predicted (Kocharovskaya et al,2001) and observed (Strekalov et al, 2001).We catalogue the main methods to realize slow light in room temperature solid, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.We will describe CPO and SBS slow light in more details.
Slow- and Fast-Light has been investigated during the last years as a powerful tool to reduce and increase the group velocity of light pulses by light. It has enjoyed much recent interest because of the practical applications for telecommunication and information systems. Among these are optical signal processing, radio frequency-photonics, nonlinear optics and time domain spectroscopy. Furthermore, it can be seen as a key technology for optical delay lines, buffers, equalizers and synchronizers in packet switched networks. For a realization, there are different methods and material systems possible. Among them the nonlinear effect of stimulated Brillouin scattering (SBS) is of special interest. This article gives an overview about the fundamentals and some experimental results of the Slow- and Fast-Light effect based on the SBS in optical fibers.
Dynamic control of the speed of a light signal, based on stimulated Brillouin scattering in optical fibers, was theoretically studied and also experimentally demonstrated as the core object of this thesis. To date, slow light based on stimulated Brillouin scattering has shown the unmatched flexibility to offer an efficient timing tool for the development of all-optical future router. Nevertheless, the seeming perfect Brillouin slow light suffered from three major obstacles: naturally narrow signal bandwidth, strong change of signal amplitude, and significant signal distortion. The essential contribution of this work has been mostly dedicated to resolve all those impairments so as to make Brillouin slow light a completely operating all-optical delay line for practical applications. Actually, high capability of tailoring the spectral distribution of the effective Brillouin resonance makes possible to resolve partially or completely all those problems. First of all, a broadband spectral window was passively obtained in between two Brillouin gain/loss resonances by simply appending two segments of fibers showing different Brillouin frequency shifts. The global Brillouin gain of the concatenated fibers manifests a gain/loss doublet resonance showing a broad window in between gain/loss peaks. In practice, this configuration has a crucial advantage that it removes the need of the pump modulation, generally used to create a polychromatic pump source. Therefore, a broadband Brillouin slow and fast light was simple realized with a reduced distortion. Secondly, the signal amplification or attenuation associated to the signal delay was completely compensated by superposing Brillouin gain and loss resonances with identical depth but different width. As a result, the Brillouin gain led to effectively a spectral hole in the center of the broadband absorption and opened a transparent window while the sharp change in the refractive index was preserve. This way it makes possible to realize zero-gain Brillouin slow light. This configuration was also exploited to produce Brillouin fast light with a total absence of signal loss, simply by swapping the spectral position of the two pumps. At last, a signal was continuously delayed through a Brillouin fiber delay line without any distortion. Due to the strong induced dispersion, pulse broadening is a major difficulty in all slow light systems and it is impossible to compensate such broadening using a linear system. Therefore, a conventional Brillouin slow light system was combined with a nonlinear optical fiber loop mirror that gives a nonlinear quadratic transmission. Using this configuration, the inevitable pulse broadening was completely compensated at the output of the loop and a signal was delayed up to one symbol without any distortion. Brillouin slow light systems were further studied in the spectral domain. For a given Brillouin resonance the spectrum of a light pulse was optimized to better match the Brillouin bandwidth. When the time envelope of a pulse was properly shaped, it was clearly observed that the spectral width of the pulse became minimized while preserving the pulse duration. This way the maximum time delay through Brillouin slow light could be enhanced for a fixed pulse width. Brillouin fast light was even realized in total absence of any pump source, which is a plain requirement for the generation of Brillouin slow or fast light. This self-generated delay line, key contribution of this thesis, relies on both spontaneous and stimulated Brillouin scattering in optical fibers. In this implementation, a light signal was strongly boosted above the so-called Brillouin threshold, so that most power of the signal was transferred to a backward propagating wave, namely the generation of amplified spontaneous Stokes wave. Since the center frequency of the intense Stokes wave is below the signal frequency by exactly Brillouin shift of the fiber used, this wave led to a Brillouin loss band centered at the signal frequency. Consequently, the signal experienced fast light propagation and the propagation velocity of the signal was self-controlled, simply by varying the signal input power. This technique has many practical advantages such as its high simplicity of the configuration and an invariant signal power in the output of this delay line. Additionally, this system self-adapts the signal bandwidth as the spectrum of the amplified Stokes wave matches the spectral distribution of the signal. An alternative method to generate all-optical delay line was proposed instead of slow light. This scheme makes use of the combination of wavelength conversion and group velocity dispersion. This type of delay line was mainly aimed at improving the storage capability of delaying element. The wavelength of a signal was simply and efficiently converted at a desired wavelength using cross gain modulation in semiconductor optical amplifiers. Then the converted signal was delivered to a high dispersive medium and arrived at the end of the medium with relative time delay due to the group velocity dispersion. A fractional delay of 140 was continuously produced through this delay line for a signal with a duration of 100 ps, preserving signal bandwidth and wavelength. The effect of slow light on linear interactions between light and matter was experimentally investigated to clarify the current scientific argument regarding slow light-enhanced Beer-Lambert absorption. It was predicted that real slowing of the light group velocity could enhance the molecular linear absorptions so as to improve the sensitivity of this type of sensing. However, the experimental results unambiguously show that material slow light (slow light in traveling wave media) does not enhance the Beer-Lambert absorption.
In this paper, we investigate slow light via stimulated Brillouin scattering (SBS) in a room temperature optical fiber that is pumped by a spectrally broadened laser. Broadening the spectrum of the pump field increases the linewidth Deltaomegapof the Stokes amplifying resonance, thereby increasing the slow-light bandwidth. One physical bandwidth limitation occurs when the linewidth becomes several times larger than the Brillouin frequency shift OmegaBso that the anti-Stokes absorbing resonance substantially cancels out the Stokes amplifying resonance and, hence, the slow-light effect. We find that partial overlap of the Stokes and anti-Stokes resonances can actually lead to an enhancement of the slow-light delay-bandwidth product when Deltaomegapsime1.3OmegaB. Using this general approach, we increase the Brillouin slow-light bandwidth to over 12 GHz from its nominal linewidth of ~30 MHz obtained for monochromatic pumping. We controllably delay 75-ps-long pulses by up to 47 ps and study the data-pattern dependence of the broadband SBS slow-light system
Slow-light delay via stimulated Brillouin scattering (SBS) in optical fibers is usually achieved with delay-dependent amplification that degrades system performance. To address this problem, we propose a SBS slow-light method that makes use of two widely separated anti-Stokes absorption resonances, and achieve nearly transparent slow light in an optical fiber. We demonstrate the method in a highly nonlinear optical fiber, and achieve a slow-light bandwidth of approximately 150 MHz and a relative of delay of approximately 0.3 for approximately 9-ns pulses with a signal attenuation of approximately 4.8 dB.