Tantalum (Ta) is a promising material for reaching long coherence times in superconducting qubits. A detailed understanding of the underlying structure-property relationship remains elusive though. In the present study, we sputter-deposited 200 nm thick Ta films on high-resistivity silicon (100) substrates at temperatures ranging from T = 20°C to 600°C, as well as on different seed layers (Nb, TiN and TaN). Alpha-Ta thin films were readily obtained at temperatures above 500°C and on all seed layers. The films were characterized in terms of surface morphology, residual-resistance ratio, crystal phase composition and superconducting transition temperature, as well as RF-performance using coplanar waveguide resonators. Internal quality factors of up to 1.5 million were measured at 100 mK in the single-photon regime. Despite similar bulk material properties, alpha-Ta films on different seed layers exhibit markedly different RF-performance, which we attribute to dissimilar strain and structural defects at the substrate-metal interfaces. Williamson-Hall analysis of XRD data reveals a clear correlation between decreasing microstrain and increasing quality factor. Cross-sectional HR-TEM further supports this interpretation by directly resolving interfacial disorder. Our results highlight the critical role of interface engineering in optimizing superconducting thin films for low-loss quantum computing circuitry.
Tantalum (Ta) is a promising material for reaching long coherence times in superconducting qubits. A detailed understanding of the underlying structure-property relationship remains elusive though. In the present study, we sputter-deposited 200 nm thick Ta films on high-resistivity silicon (100) substrates at temperatures ranging from T = 20°C to 600°C, as well as on different seed layers (Nb, TiN and TaN). Alpha-Ta thin films were readily obtained at temperatures above 500°C and on all seed layers. The films were characterized in terms of surface morphology, residual-resistance ratio, crystal phase composition and superconducting transition temperature, as well as RF-performance using coplanar waveguide resonators. Internal quality factors of up to 1.5 million were measured at 100 mK in the single-photon regime. Despite similar bulk material properties, alpha-Ta films on different seed layers exhibit markedly different RF-performance, which we attribute to dissimilar strain and structural defects at the substrate-metal interfaces. Williamson-Hall analysis of XRD data reveals a clear correlation between decreasing microstrain and increasing quality factor. Cross-sectional HR-TEM further supports this interpretation by directly resolving interfacial disorder. Our results highlight the critical role of interface engineering in optimizing superconducting thin films for low-loss quantum computing circuitry.
Superconducting qubits are a promising platform for large-scale quantum computing. Besides the Josephson junction, most parts of a superconducting qubit are made of a planar, patterned superconducting thin films. In the past, most qubit architectures have relied on niobium (Nb) as the material of choice for the superconducting layer. However, there is also a variety of alternative materials with potentially less losses, which may thereby result in increased qubit performance. One such material is tantalum (Ta), for which high-performance qubit components have already been demonstrated. In this study, we report the sputter-deposition of Ta thin films directly on heated and unheated silicon (Si) substrates as well as onto different, nanometer-thin seed layers from tantalum nitride (TaN), titanium nitride (TiN) or aluminum nitride (AIN) that were deposited first. The thin films are characterized in terms of surface morphology, crystal structure, phase composition, critical temperature, residual resistance ratio (RRR) and RF-performance. We obtain thin films indicative of pure alpha-Ta for high temperature (600°C) sputtering directly on silicon and for Ta deposited on TaN or TiN seed layers. Coplanar waveguide (CPW) resonator measurements show that the Ta deposited directly on the heated silicon substrate performs best with internal quality factors Qi reaching 1xl06in the single-photon regime, measured at T=100 mK.
Tantalum has been demonstrated as a promising material for superconducting qubits. However, comparatively little attention has been given to its nitrides. Tantalum nitride exhibits a range of stoichiometries, resulting in a variety of material properties, including both superconducting and non-superconducting phases. Owing to this versatility, tantalum nitrides can serve multiple purposes in superconducting qubits: as seed layers for alpha-Ta growth, as a superconducting base material and as a non-superconducting barrier in the Josephson junction. In this study, we explore the performance of superconducting TaN and Ta thin film combinations on silicon substrates in terms of internal quality factor Qi. We find that standalone TaN films exhibit Qi values of about 1.5x10^5 at 100mK in the single-photon regime. Surprisingly, a resonator made from Ta grown on a few-nanometers-thick TaN seed layer yields largely the same performance. However, adding an additional, few-nanometers-thick Ta buffer layer between the Si substrate and this TaN seed layer enhances Qi significantly up to 5.9x10^5. Supporting transmission electron microscopy measurements reveal nitrogen accumulation and structural disorder at the TaN-Si interface, while this interfacial modification is suppressed when the Ta buffer layer is introduced. The observed improvement in resonator performance is consistent with a reduction of interface-related two-level system losses and strongly supports the hypothesis that controlling the substrate-metal interface is pivotal for the performance of superconducting qubit circuitry.
Tantalum thin films sputtered on unheated silicon substrates are characterized with microwaves at around 10 GHz in a 10 mK environment. We show that the phase of tantalum with a body-centered cubic lattice (α-Ta) can be grown selectively by depositing a niobium buffer layer prior to a tantalum film. The physical properties of the films, such as superconducting transition temperature and crystallinity, change markedly with the addition of the buffer layer. Coplanar waveguide resonators based on the composite film exhibit significantly enhanced internal quality factors compared with a film without the buffer layer. The internal quality factor approaches 2 × 107 at a large-photon-number limit. While the quality factor decreases at the single-photon level owing to two-level system (TLS) loss, we have deduced that one of the causes of TLS loss is the amorphous silicon layer at the film–substrate interface, which originates from the substrate cleaning before the film deposition rather than the film itself. The temperature dependence of the internal quality factors shows a marked rise below 200 mK, suggesting the presence of TLS–TLS interactions. The present low-loss tantalum films can be deposited without substrate heating and thus have various potential applications in superconducting quantum electronics.
Superconducting qubits based on tantalum (Ta) thin films have demonstrated the highest-performing microwave resonators and qubits. This makes Ta an attractive material for superconducting quantum computing applications, but, so far, direct deposition has largely relied on high substrate temperatures exceeding \SI{400}{\celsius} to achieve the body-centered cubic phase, BCC (\textalpha-Ta). This leads to compatibility issues for scalable fabrication leveraging standard semiconductor fabrication lines. Here, we show that changing the sputter gas from argon (Ar) to krypton (Kr) promotes BCC Ta synthesis on silicon (Si) at temperatures as low as \SI{200}{\celsius}, providing a wide process window compatible with back-end-of-the-line fabrication standards. Furthermore, we find these films to have substantially higher electronic conductivity, consistent with clean-limit superconductivity. We validated the microwave performance through coplanar waveguide resonator measurements, finding that films deposited at \SI{250}{\celsius} and \SI{350}{\celsius} exhibit a tight performance distribution at the state of the art. Higher temperature-grown films exhibit higher losses, in correlation with the degree of Ta/Si intermixing revealed by cross-sectional transmission electron microscopy. Finally, with these films, we demonstrate transmon qubits with a relatively compact, \SI{20}{\micro\meter} capacitor gap, achieving a median quality factor up to 14 million.
Tantalum films incorporated into superconducting circuits have exhibited low surface losses, resulting in long-lived qubit states. The remaining loss pathways originate in microscopic defects that manifest as two level systems (TLSs) at low temperatures. These defects limit performance, so careful attention to tantalum film structures is critical for optimal use in quantum devices. In this work, we investigate the growth of tantalum using magnetron sputtering on sapphire, Si, and photoresist substrates. In the case of sapphire, we present procedures for the growth of fully-oriented films with α-Ta [1 1 1]//Al2O3 [0 0 0 1] and α-Ta [1 −1 0]//Al2O3 [1 0 −1 0] orientational relationships and having residual resistivity ratio (RRR) ∼ 60 for 220 nm thick films. On Si, we find a complex grain texturing with Ta [1 1 0] normal to the substrate and RRR ∼ 30. We further demonstrate airbridge fabrication using Nb to nucleate α-Ta on photoresist surfaces. For the films on sapphire, resonators show TLS-limited quality factors of 1.3 ± 0.3 × 106 at 10 mK (for a waveguide gap and conductor width of 3 and 6 μm, respectively). Structural characterization using scanning electron microscopy, x-ray diffraction, low temperature transport, secondary ion mass spectrometry, and transmission electron microscopy reveal the dependence of residual impurities and screw dislocation density on processing conditions. The results provide practical insights into the fabrication of advanced superconducting devices including qubit arrays and guide future works on crystallographically deterministic qubit fabrication.
Abstract Tantalum (Ta) has recently received considerable attention in manufacturing robust superconducting quantum circuits. Ta offers low microwave loss, high kinetic inductance compared to aluminium (Al) and niobium (Nb), and good compatibility with complementary metal-oxide-semiconductor (CMOS) technology, which is essential for quantum computing applications. Here we demonstrate the fabrication engineering of thickness-dependent high-quality-factor (high- Qi ) Ta superconducting microwave coplanar waveguide resonators. All films are deposited on high-resistivity silicon substrates at room temperature without additional substrate heating. Before Ta deposition, a niobium (Nb) seed layer is used to promote a body-centred cubic lattice ( α -Ta) formation. We further engineer the kinetic inductance ( LK ) of the resonators by varying Ta film thicknesses. High LK is a key advantage for applications because it facilitates the realisation of high-impedance, compact quantum circuits with enhanced coupling to qubits. The maximum internal quality factor Qi of ∼ 3.6 × 10 6 in the high power regime and Qi of ∼ 4.5 × 10 5 in the single-photon regime is achieved for 100 nm Ta which represents an improvement over previous room-temperature deposited Ta resonators on silicon substrates in the single photon regime, while the highest kinetic inductance of 0.6 pH/sq is obtained for the thinnest film, which is 40 nm. This combination of high Qi and high LK highlights the potential of Ta microwave circuits for high-fidelity operation of compact quantum circuits.