Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2606.17866

Experimental Characterization and Modeling of Measurement-Induced State-Transitions in a Fluxonium Superconducting Qubit

Martijn F. S. Zwanenburg, Jinlun Hu, Eugene Y. Huang, Figen Yilmaz, Siddharth Singh, Christian Kraglund Andersen

quant-phSubmitted Jun 16, 2026• Announced Jun 17, 2026• 0 citations
arXivHTMLPDF

Abstract

Superconducting qubits are most often measured using dispersive readout, which, ideally, implements a projective quantum non-demolition (QND) measurement. While a larger readout drive can increase the signal and, thus, reduce discrimination errors in the readout, strong microwave drives may also cause non-QND errors by driving the qubit to a state outside the computational subspace. In this work, we experimentally characterize measurement-induced state transitions (MIST) in a fluxonium qubit over its full external flux range. We further numerically calculate the MIST errors, and find that the theory accurately predicts eleven experimentally identified regions with increased MIST. In addition to transitions to higher fluxonium levels, we also find that, at certain flux points, MIST errors are dominated by transitions that include the transmission-line-like array modes of the fluxonium's superinductor. The excellent match between theory and experiment validates that the models accurately predict the occurrence of MIST in these systems, and further highlights the influence of array modes in fluxonium readout.

Comments
11 pages, 6 figures

Related papers

Impact of Josephson-Junction Array Modes on Fluxonium Readout

Shraddha Singh, Gil Refael, Aashish A. Clerk +1 more

Dispersive readout of superconducting qubits is often limited by readout-drive-induced transitions between qubit levels. While there is a growing understanding of such effects in transmon qubits, the case of highly nonlinear fluxonium qubits is more complex. We theoretically analyze measurement-induced state transitions (MISTs) during the dispersive readout of a fluxonium qubit. We focus on a new mechanism: a simultaneous transition/excitation involving the qubit and an internal mode of the Josephson-junction array in the fluxonium circuit. Using an adiabatic Floquet approach, we show that these new kinds of MIST processes can be relevant when using realistic circuit parameters and relatively low readout drive powers. They also contribute to excess qubit dephasing even after a measurement is complete. In addition to outlining basic mechanisms, we also investigate the dependence of such transitions on the circuit parameters. We find that with a judicious choice of frequency allocations or coupling strengths, these parasitic processes can most likely be avoided.

arXiv:2412.14788•PRX Quantum•Aug 26, 2025•10 citations

Readout-induced leakage of the fluxonium qubit

Aayam Bista, Matthew Thibodeau, Ke Nie +3 more

Dispersive readout is widely used to perform high-fidelity measurement of superconducting qubits. Much work has been focused on the qubit readout fidelity, which depends on the achievable signal-to-noise ratio and the qubit relaxation time. As groups have pushed to increase readout fidelity by increasing readout photon number, dispersive readout has been shown to strongly affect the postmeasurement qubit state. Such effects hinder the effectiveness of quantum error correction, which requires measurements that both have high readout fidelity and are quantum nondemolition (QND). Here, we experimentally investigate non-QND effects in the fluxonium. We map out the state evolution of fluxonium qubits in the presence of resonator photons and observe that these photons induce transitions in the fluxonium both within and outside the qubit subspace. We numerically model our system and find that transitions to higher-excited states and coupling to an external spurious mode are necessary to explain observed non-QND effects.

arXiv:2501.17807•Physical Review Applied•Feb 9, 2026•5 citations

Measurement-induced state transitions across the fluxonium qubit landscape

Alex A. Chapple, Boris M. Varbanov, Alexander McDonald +1 more

Understanding the mechanisms that limit high-fidelity readout in circuit quantum electrodynamics is essential for its optimization. Multi-photon resonances are understood to be a limiting factor, causing population transfer from the computational states to higher-energy states under drive. This effect, known as measurement-induced state transitions, has been extensively studied for the transmon qubit. While this exploration has begun for the fluxonium qubit, a systematic study of this effect is lacking. Here, we bridge this gap by theoretically studying measurement-induced state transitions in the fluxonium qubit over a wide range of parameters, comprising essentially all experimentally explored ranges. We find that lighter fluxoniums are less susceptible to these state transitions when compared to their heavier counterparts. We attribute this effect to the combination of lower density of multi-photon resonances, a smaller requisite coupling for a given dispersive shift, and a more harmonic-like structure of the charge operator. We confirm the validity of our analysis by performing time-dependent readout simulations. Finally, we consider the impact of the superinductor's array modes on measurement-induced state transitions over a large range of parameters.

quant-pharXiv:2604.08515•Apr 10, 2026•0 citations

Full characterization of measurement-induced transitions of a superconducting qubit

Connolly, Thomas, Pavel D. Kurilovich, Vladislav D. Kurilovich +12 more

Repeated quantum non-demolition measurement is a cornerstone of quantum error correction protocols. In superconducting qubits, the speed of dispersive state readout can be enhanced by increasing the power of the readout tone. However, such an increase has been found to result in additional qubit state transitions that violate the desired quantum non-demolition character of the measurement. Recently, the readout of a transmon superconducting qubit was improved by using a tone with frequency much larger than the qubit frequency. Here, we experimentally identify the mechanisms of readout-induced transitions in this regime. In the dominant mechanism, the energy of an incoming readout photon is partially absorbed by the transmon and partially returned to the transmission line as a photon with lower frequency. Other mechanisms involve the excitation of unwanted package modes, decay via material defects, and, at higher qubit frequencies, the activation of undesired resonances in the transmon spectrum. Our work provides a comprehensive characterization of superconducting qubit state transitions caused by a strong drive.

arXiv:2506.05306•Jun 5, 2025•0 citations

Measurement-Induced State transitions in Inductively-Shunted Transmons

Nicholas Zobrist, John Mark Kreikebaum, Mostafa Khezri +6 more

Fast and high-fidelity qubit measurement plays a key role in quantum error correction. In superconducting qubits, measurement is typically performed using a resonant microwave drive on a readout resonator dispersively coupled to the qubit. Shorter measurement times require larger numbers of photons populating the readout resonator, which ultimately leads to undesired measurementinduced state transitions (MIST) of the qubit. MIST can be particularly problematic because these transitions often leave the qubit in a high energy state, and the MIST locations in readout parameter space drift as a function of qubit offset charge. In transmon qubits, these drifts have been avoided using very large qubit-resonator detunings or dedicated offset charge biases. In this work, we take an alternative approach and add an inductive shunt to the transmon to eliminate the offset charge dependence and stabilize the MIST. We experimentally characterize MIST in several different inductively-shunted transmons, in agreement with quantum and semiclassical models for MIST. These results extend to other inductively-shunted qubits.

quant-pharXiv:2603.12114•Mar 13, 2026•0 citations

Measurement-induced state transitions in dispersive qubit-readout schemes

Konstantin Nesterov, Ivan Pechenezhskiy

The dispersive-readout scheme enables quantum nondemolition measurement of superconducting qubits. An increased readout power can shorten the readout time and reduce the state-discrimination error but can promote qubit transitions into higher noncomputational states. The ability to predict the onset of these measurement-induced state transitions can aid the optimization of qubit circuits and provide means for comparing the readout performance of different qubit types. Building upon the concept of dressed coherent states, we consider two straightforward metrics for determining the maximum number of photons that can be used for dispersive readout without causing state transitions. We focus on the fluxonium readout to demonstrate the independence of the metrics from any qubit-type-specific approximations. The dispersive readout of transmons and other superconducting qubits can be treated universally in the same fashion.

arXiv:2402.07360•Physical Review Applied•Dec 10, 2024•15 citations
Superconducting qubits are most often measured using dispersive readout, which, ideally, implements a projective quantum non-demolition (QND) measurement. While a larger readout drive can increase the signal and, thus, reduce discrimination errors in the readout, strong microwave drives may also cause non-QND errors by driving the qubit to a state outside the computational subspace. In this work, we experimentally characterize measurement-induced state transitions (MIST) in a fluxonium qubit over its full external flux range. We further numerically calculate the MIST errors, and find that the theory accurately predicts eleven experimentally identified regions with increased MIST. In addition to transitions to higher fluxonium levels, we also find that, at certain flux points, MIST errors are dominated by transitions that include the transmission-line-like array modes of the fluxonium's superinductor. The excellent match between theory and experiment validates that the models accurately predict the occurrence of MIST in these systems, and further highlights the influence of array modes in fluxonium readout.
Dispersive readout of superconducting qubits is often limited by readout-drive-induced transitions between qubit levels. While there is a growing understanding of such effects in transmon qubits, the case of highly nonlinear fluxonium qubits is more complex. We theoretically analyze measurement-induced state transitions (MISTs) during the dispersive readout of a fluxonium qubit. We focus on a new mechanism: a simultaneous transition/excitation involving the qubit and an internal mode of the Josephson-junction array in the fluxonium circuit. Using an adiabatic Floquet approach, we show that these new kinds of MIST processes can be relevant when using realistic circuit parameters and relatively low readout drive powers. They also contribute to excess qubit dephasing even after a measurement is complete. In addition to outlining basic mechanisms, we also investigate the dependence of such transitions on the circuit parameters. We find that with a judicious choice of frequency allocations or coupling strengths, these parasitic processes can most likely be avoided.
Dispersive readout is widely used to perform high-fidelity measurement of superconducting qubits. Much work has been focused on the qubit readout fidelity, which depends on the achievable signal-to-noise ratio and the qubit relaxation time. As groups have pushed to increase readout fidelity by increasing readout photon number, dispersive readout has been shown to strongly affect the postmeasurement qubit state. Such effects hinder the effectiveness of quantum error correction, which requires measurements that both have high readout fidelity and are quantum nondemolition (QND). Here, we experimentally investigate non-QND effects in the fluxonium. We map out the state evolution of fluxonium qubits in the presence of resonator photons and observe that these photons induce transitions in the fluxonium both within and outside the qubit subspace. We numerically model our system and find that transitions to higher-excited states and coupling to an external spurious mode are necessary to explain observed non-QND effects.
Understanding the mechanisms that limit high-fidelity readout in circuit quantum electrodynamics is essential for its optimization. Multi-photon resonances are understood to be a limiting factor, causing population transfer from the computational states to higher-energy states under drive. This effect, known as measurement-induced state transitions, has been extensively studied for the transmon qubit. While this exploration has begun for the fluxonium qubit, a systematic study of this effect is lacking. Here, we bridge this gap by theoretically studying measurement-induced state transitions in the fluxonium qubit over a wide range of parameters, comprising essentially all experimentally explored ranges. We find that lighter fluxoniums are less susceptible to these state transitions when compared to their heavier counterparts. We attribute this effect to the combination of lower density of multi-photon resonances, a smaller requisite coupling for a given dispersive shift, and a more harmonic-like structure of the charge operator. We confirm the validity of our analysis by performing time-dependent readout simulations. Finally, we consider the impact of the superinductor's array modes on measurement-induced state transitions over a large range of parameters.
Repeated quantum non-demolition measurement is a cornerstone of quantum error correction protocols. In superconducting qubits, the speed of dispersive state readout can be enhanced by increasing the power of the readout tone. However, such an increase has been found to result in additional qubit state transitions that violate the desired quantum non-demolition character of the measurement. Recently, the readout of a transmon superconducting qubit was improved by using a tone with frequency much larger than the qubit frequency. Here, we experimentally identify the mechanisms of readout-induced transitions in this regime. In the dominant mechanism, the energy of an incoming readout photon is partially absorbed by the transmon and partially returned to the transmission line as a photon with lower frequency. Other mechanisms involve the excitation of unwanted package modes, decay via material defects, and, at higher qubit frequencies, the activation of undesired resonances in the transmon spectrum. Our work provides a comprehensive characterization of superconducting qubit state transitions caused by a strong drive.
Fast and high-fidelity qubit measurement plays a key role in quantum error correction. In superconducting qubits, measurement is typically performed using a resonant microwave drive on a readout resonator dispersively coupled to the qubit. Shorter measurement times require larger numbers of photons populating the readout resonator, which ultimately leads to undesired measurementinduced state transitions (MIST) of the qubit. MIST can be particularly problematic because these transitions often leave the qubit in a high energy state, and the MIST locations in readout parameter space drift as a function of qubit offset charge. In transmon qubits, these drifts have been avoided using very large qubit-resonator detunings or dedicated offset charge biases. In this work, we take an alternative approach and add an inductive shunt to the transmon to eliminate the offset charge dependence and stabilize the MIST. We experimentally characterize MIST in several different inductively-shunted transmons, in agreement with quantum and semiclassical models for MIST. These results extend to other inductively-shunted qubits.
The dispersive-readout scheme enables quantum nondemolition measurement of superconducting qubits. An increased readout power can shorten the readout time and reduce the state-discrimination error but can promote qubit transitions into higher noncomputational states. The ability to predict the onset of these measurement-induced state transitions can aid the optimization of qubit circuits and provide means for comparing the readout performance of different qubit types. Building upon the concept of dressed coherent states, we consider two straightforward metrics for determining the maximum number of photons that can be used for dispersive readout without causing state transitions. We focus on the fluxonium readout to demonstrate the independence of the metrics from any qubit-type-specific approximations. The dispersive readout of transmons and other superconducting qubits can be treated universally in the same fashion.