Scaling quantum computers to large sizes requires the implementation of many parallel qubit readouts. Here we present an ultrastable superconducting-qubit readout method using the multi-tone self-phase-referenced Pound-Drever-Hall (PDH) technique, originally developed for use with optical cavities. In this work, we benchmark PDH readout of a single transmon qubit, using room-temperature heterodyne detection of all tones to reconstruct the PDH signal. We demonstrate that PDH qubit readout is insensitive to microwave phase drift, displaying $0.73^\circ$ phase stability over 2 hours, and capable of single-shot readout in the presence of phase errors exceeding the phase shift induced by the qubit state. We show that the PDH sideband tones do not cause unwanted measurement-induced state transitions for a transmon qubit, leading to a potential signal enhancement of at least $14$~dB over traditional heterodyne readout.
Scaling quantum computers to large sizes requires the implementation of many parallel qubit readouts. Here we present an ultrastable superconducting-qubit readout method using the multi-tone self-phase-referenced Pound-Drever-Hall (PDH) technique, originally developed for use with optical cavities. In this work, we benchmark PDH readout of a single transmon qubit, using room-temperature heterodyne detection of all tones to reconstruct the PDH signal. We demonstrate that PDH qubit readout is insensitive to microwave phase drift, displaying 0.73∘ phase stability over 2 hours, and capable of single-shot readout in the presence of phase errors exceeding the phase shift induced by the qubit state. We show that the PDH sideband tones do not cause unwanted measurement-induced state transitions for a transmon qubit, leading to a potential signal enhancement of at least 14~dB over traditional heterodyne readout.
We present a cavity-enhanced optical absorption measurement technique based on high-bandwidth Pound-Drever-Hall (PDH) sideband locking, which naturally provides a real-time, resonant amplitude quadrature readout that can be mapped onto the cavity’s internal loss rate. Cavity-enhancement is widely used in the detection of small signals -- an optical cavity traps photons between two highly reflective mirrors, thereby enhancing the effective path length through the absorber [Romanini et al., 2014]. Most of the available techniques, however, probe transmission signals and/or do not provide the stability required for the detection of fast signals.To ensure optimal enhancement of absorption sensitivity, probe light must be locked on resonance with the cavity. PDH locking relies on phase modulation of a laser beam, creating two sidebands on the original carrier frequency [Black, 2001]. Upon reflection from a cavity, this modulated light produces a heterodyne signal (beat note) that can be detected and demodulated. We use the phase quadrature of the beat note to lock the cavity on resonance with one of the sidebands, achieving a locking bandwidth in the MHz range that keeps cavity and probe light resonant for hours [Reinhardt et al., 2017]. Simultaneously, we monitor the amplitude quadrature, which provides a continuous, real-time, heterodyne-amplified readout of the cavity’s internal absorption. Our PDH sideband cavity-enhanced absorption readout technique (SideCAR) ensures high sensitivity without reaching saturation limits in the intracavity medium by keeping a relatively low intracavity power, since only one of the sidebands is allowed to enter the cavity, but the signal is boosted above the detector noise by heterodyne detection (using the carrier as a local oscillator).This thesis presents the theoretical formulation of the sensing technique together with the expressions for the sensitivity limit (ultimately given by the laser quantum noise), and the experimental results from a test cavity setup. Probing a proof-of-concept 5-cm-long Fabry-Perot cavity with a coupled power of 160 uW, we measure an absorption sensitivity of 7*10^(-11) cm^(-1)/sqrt(Hz) at 100 kHz (roughly the cavity bandwidth), a factor of 11 from the shot-noise limit. This technique allows the detection of small, transient signals against absorptive backgrounds with sensitivity close to the shot noise limit using a reflection-based measurement in a fairly simple setup, opening the possibility of developing new microscopic single-port real-world sensors for transients, for example using micron-scale optical fiber cavities
Abstract High-fidelity and rapid readout of a qubit state is key to quantum computing and communication, and it is a prerequisite for quantum error correction. We present a readout scheme for superconducting qubits that combines two microwave techniques: applying a shelving technique to the qubit that effectively increases the energy-relaxation time, and a two-tone excitation of the readout resonator to distinguish among qubit populations in higher energy levels. Using a machine-learning algorithm to post-process the two-tone measurement results further improves the qubit-state assignment fidelity. We perform single-shot frequency-multiplexed qubit readout, with a 140 ns readout time, and demonstrate 99.5% assignment fidelity for two-state readout and 96.9% for three-state readout—without using a quantum-limited amplifier.
Suppressing high-frequency laser phase noise, particularly at frequencies near and beyond typical feedback bandwidths of a few MHz, is a critical yet challenging task in many advanced applications. Feedforward-based methods generally outperform feedback in high-frequency range, but their performances are more susceptible to perturbations. In this work, we focus on the Pound-Drever-Hall (PDH)-feedforward method we demonstrated recently [Yu-Xin Chao et al., Optica 11(7), 945-950 (2024)] and analyze the factors that affect its long-term stability. By constructing a simple circuit allowing for adaptive control of the feedforward gain in response to power fluctuations of cavity transmission, we demonstrate a robust ≥40 dB suppression of laser phase noise around 2 MHz and a noise suppression bandwidth up to 50 MHz. In comparison, when using normal PDH feedback, robust noise suppression of over 40 dB can only occur for frequencies below tens of kHz in most setups. Our findings may pave the way for general usage of PDH feedforward and allow for simple construction of low-noise lasers for precise quantum controls and precision metrology.
In the quest to build a fault-tolerant quantum computer, superconducting circuits based on Josephson junctions have emerged as a leading architecture. Coherence times have increased significantly over the last two decades, and processors with ∼ 50 qubits have been experimentally demonstrated. These systems traditionally utilize microwave frequency control signals, and heterodyne based detection schemes for measurement. Both of these techniques rely heavily on room temperature microwave generators, high-bandwidth lines from room temperature to millikelvin temperatures, and bulky non-reciprocal elements such as cryogenic microwave isolators. Reliance on these elements makes it impractical to scale existing devices up a single order of magnitude, let alone the 5-6 orders of magnitude needed for performing fault-tolerant quantum algorithms. Here, I present results that suggesting superconducting digital logic, namely Single Flux Quantum (SFQ) logic, can replace analog control and measurement techniques, avoiding the significant overhead involved. I describe a scheme for measuring qubits with a device known as a Josephson Photomultiplier (JPM), which crucially stores the result of a qubit measurement in a classical circulating supercurrent within the device and allows for integration with SFQ detection circuitry. This technique is experimentally demonstrated, with single-shot measurement fidelity of 92%. Two methods for accessing this measurement result are presented, one utilizing ballistic fluxons, and another utilizing flux comparison. Initial experimental results of the latter are presented. In addition, I describe a scheme for controlling qubits with sequences of digital SFQ pulses. This method is then used to control a qubit without a microwave signal generator, with results of an average single-qubit gate fidelity of around 95%. When combined, these techniques form a nearly fully digital interface to superconducting qubits, which could allow these systems to scale much more easily.
The Pound--Drever--Hall (PDH) technique is routinely used to stabilize the frequency of a laser to a reference cavity. Electronic sideband (ESB) locking, a PDH variant, bridges the frequency gap between the discrete cavity resonances and a desired laser frequency. Here we use quadrature amplitude modulation (QAM), a standard technique in digital communications, to generate the high-quality phase-modulated radio-frequency (rf) drive required for ESB locking. We develop a theoretical framework to analyze how in-phase/quadrature-phase (I/Q) impairments distort the ESB error signal and induce frequency offsets relevant to ultranarrow-linewidth lasers. We then design and implement a direct software-defined radio (SDR) on an UltraScale+ RFSoC platform, frequently adopted across modern quantum-computing systems, to digitally compensate QAM I/Q impairments. Using this device, we generate phase-modulated rf signals with a large phase-modulation index of 1.01 rad and root-mean-square I/Q errors below 0.3% over a carrier-frequency range of 350MHz to 1.75GHz. Finally, we lock a laser to an ultralow expansion (ULE) reference cavity and demonstrate continuous laser-frequency tuning by ramping the carrier frequency while maintaining lock, validating the continuous tunability of our ESB locking instrument.
As superconducting quantum processors increase in size and complexity, the scalability of standard techniques for qubit control and readout becomes a limiting factor. Replacing room temperature analog components with cryogenic digital components could allow for the realization of systems well beyond the current state-of-the-art qubit arrays with tens of qubits. The standard technique for performing a qubit measurement with heterodyne readout uses a quantum-limited cryogenic amplifier chain and requires bulky microwave components inside the refrigerator with multiple control lines and pump signals. Additionally, the result is only accessible in software at room temperature. An alternative method for measuring qubits involves mapping the qubit state onto the photon occupation in a microwave cavity, followed by subsequent photon detection using a Josephson photomultiplier (JPM). The JPM measures the qubit and stores the result in a classical circulating current. To make use of this result, we can leverage existing single flux quantum (SFQ) circuitry. An underdamped Josephson transmission line (JTL) can be coupled to the JPM and fluxons traveling along the JTL are accelerated or delayed, depending on the circulating current state of the JPM. This fluxon delay can then be converted to an SFQ logic signal resulting in a digital qubit readout with a proximal microfabricated device, paving the way for cryogenic digital feedback necessary for error-correcting codes.