Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2511.23090 · Journal of Applied Physics

Nonequilibrium Quasiparticle Dynamics in a MoRe-Based Superconducting Resonator under IR Excitation

O. A. Kalenyuk, S. I. Futimsky, I. A. Martynenko, A. P. Shapovalov, O. O. Boliasova, V. I. Shnyrkov, A. L. Kasatkin, A. A. Kordyuk

cond-mat.supr-concond-mat.mtrl-sciquant-phSubmitted Nov 28, 2025• Announced Dec 1, 2025• 0 citations• Revised Feb 20, 2026 (v2)
v1 · Nov 28, 2025v2 · Feb 20, 2026
arXivHTMLPDF

Abstract

The response of a MoRe-based superconducting resonator operating near 5 K to pulsed infrared irradiation is investigated, and the underlying physical mechanisms are analyzed. The device exhibits a pronounced nonlinear response dominated by nonequilibrium quasiparticle dynamics rather than uniform thermal heating. Infrared pulses produce strong distortions of the resonance curve and a transient decrease in the resonance frequency, consistent with increased kinetic inductance caused by quasiparticle generation. The frequency shift scales approximately linearly with absorbed power, whereas the dissipation response saturates at higher powers, indicating the formation of a nonequilibrium steady-state quasiparticle population. These observations demonstrate a transition from a linear pair-breaking regime to a saturated dissipation regime, likely associated with a quasiparticle relaxation bottleneck or partial suppression of the smaller superconducting gap in MoRe. The results highlight the relevance of nonequilibrium processes in MoRe and confirm its potential for microwave kinetic-inductance detector applications.

Journal reference
J. Appl. Phys. 139, 073905 (2026)
DOI
10.1063/5.0314771

Related papers

Nonequilibrium behaviour and quasiparticle heating in thin film superconducting microwave resonators

Tejas Guruswamy

In this thesis I describe work on developing theoretical and numerical models of supercon- ducting thin-film microwave resonators. Superconducting resonators are used in a variety of applications, one of which is as kinetic inductance detectors (KIDs). KIDs are ultra-low noise, highly sensitive, multiplexable detectors, with uses in a wide variety of fields including astrophysics, medical imaging, and particle physics. Resonators are also crucial for supercon- ducting qubit readout, superconducting mixers and parametric amplifiers, and as multiplexers for other devices. The results described in this thesis apply to all thin film resonators, but are primarily described in the context of KIDs. I develop models of how constant absorbed power affects superconducting thin films, driving them out of thermal equilibrium with the bath. Using the Chang & Scalapino equations, I calculate numerically the steady-state quasiparticle and phonon distributions for various sources of power (sub-gap and above-gap photons and phonons, single frequency and broadband). Many new results emerge, a few of which are: the quasiparticle heating effects of microwave power, explaining the experimentally measured saturation of resonator performance; the frequency dependence of the quasiparticle generation efficiency in the sub-mm wavelength range; and the importance of phonon trapping in thin films at low temperatures. I then use these nonequilibrium results in higher-level device models. Starting from a generic framework for resonators, I present and implement a model of a KID with variable thermal isolation. I calculate the effects of quasiparticle heating on both the large-signal and small-signal behaviour, highlighting the effects of electrothermal feedback caused by readout power. Electrothermal feedback is shown to be able to increase or decrease the magnitude and bandwidth of the responsivity and noise, depending on the operating point. Finally, I propose an experimental measurement of quasiparticle heating effects in a new device – a four-port ring resonator. In such a device, unlike in the standard two-port resonator, the device can be heated and read out independently. I develop detailed models for the thermal and electrical behaviour of these devices, and suggest a scheme by which the quasiparticle heating effects of microwave power, predicted in this thesis, can be measured.

•Dec 20, 2017•8 citations

Modeling the dynamics of quasiparticles in superconducting devices at low temperatures

Fischer, Paul Benedikt

Superconducting materials are useful for a wide range of applications, ranging from particle detectors to quantum computing. The presence of excitations (quasiparticles) in the superconductor can be a resource in some devices and a disturbance in others - in kinetic inductance detectors, the generation of quasiparticles by an incoming photon can be read out and used to calculate the energy of the photon, while the tunnelling of quasiparticles is a cause of decoherence in quantum computing. While early research mostly focused on superconductors close to the critical temperature, temperatures that are far below the critical temperatures are often used for current applications. At these low temperatures, the energy exchange between quasiparticles and phonons becomes slow, and even small disturbances may drive the energy distribution of the quasiparticles out of thermal equilibrium. In fact, experiments usually show a residual number of quasiparticles even at milikelvin temperatures, for which the thermal density of quasiparticles would be negligible. This thesis consists of two parts: In the first part, I model the energy distribution of quasiparticles in superconducting resonators: Quasiparticles absorb energy by absorbing photons and release it as phonons, which drives the superconductor out of thermal equilibrium. I solve a set of rate equations, both numerical and analytical, to calculate the energy distribution of the quasiparticles. For parameters typically used in kinetic inductance detectors made of aluminum, the microwave signal used to read out the resonator dominates the energy distribution of the quasiparticles, while their density is determined by other processes. At not too low temperatures, quasiparticles are mainly produced by thermal phonons, and my calculations reproduce recently measured quality factors of resonators at temperatures above 250 mK without free parameters. I show that even a very small number of photons of higher energy, which I ascribe to noise from the microwave generator, would dominate the quasiparticle density at lower temperatures. Under this assumption, my calculations also reproduce the quality factors at lower temperatures. In the second part of this thesis, I investigate the effects of spatial fluctuations of the superconducting energy gap on the dynamics of quasiparticles. Recently, it has been proposed that such fluctuations may lead to the localization of quasiparticles in states below the energy gap, which could cause a finite quasiparticle density even at very low temperatures. Using the Keldysh-Usadel formalism, I derive rates for the different processes (recombination/(de-) localization/generation) of quasiparticles in such systems. Using these rate equations I derive new upper limits for the quasiparticle density that could result from these localized states. These upper limits show that localization caused by weak magnetic impurities in typical aluminum systems does not lead to a relevant quasiparticle density. This contradicts previous theories, which only consider the recombination between two localized quasiparticles without examining their dynamics in detail.

•Jan 1, 2025•0 citations

Nonequilibrium pulse dynamics and metastable latching in nonlinear kinetic inductance detectors

M. Rouble, C. Albert, P. Day +3 more

Microwave kinetic inductance detectors are typically operated at high readout power to raise the detector signal above system noise. At sufficiently large readout power, the current-dependent kinetic inductance couples the detector response to its readout bias. Using a nonlinear resonator framework and time-domain circuit calculations, we show that the amplitude, shape, and relaxation time of the driven detector's response depend on both the absorbed energy and on the readout bias. Strongly driven bias points produce amplified, extended, and non-exponential pulse responses. Qualitative agreement between calculated and measured pulse responses indicates that these effects are dominated by the driven nonlinear resonator dynamics rather than by altered quasiparticle dynamics. Beyond resonance bifurcation, sufficiently large pulse events drive the resonator between stable branches, resulting in a metastable latched state which persists after the quasiparticle transient has decayed. The pulse energy required for branch switching is set by the readout bias, suggesting a mode of triggered detection with an in-situ tunable threshold. Although nonlinear operation requires calibration of the bias- and energy-dependent response, the enhanced pulse amplitude and duration, together with tunable latching and the ability to select these parameters via the readout operating state, are likely to be of interest for single-photon and rare-event experiments, especially those limited by amplifier or system noise.

arXiv:2608.23902•Aug 24, 2026•0 citations

Evidence of a Nonequilibrium Distribution of Quasiparticles in the Microwave Response of a Superconducting Aluminum Resonator

Pieter de Visser, D. J. Goldie, P. Diener +3 more

In a superconductor, absorption of photons with an energy below the superconducting gap leads to redistribution of quasiparticles over energy and thus induces a strong nonequilibrium quasiparticle energy distribution. We have measured the electrodynamic response, quality factor, and resonant frequency of a superconducting aluminium microwave resonator as a function of microwave power and temperature. Below 200 mK, both the quality factor and resonant frequency decrease with increasing microwave power, consistent with the creation of excess quasiparticles due to microwave absorption. Counterintuitively, above 200 mK, the quality factor and resonant frequency increase with increasing power. We demonstrate that the effect can only be understood by a nonthermal quasiparticle distribution.

arXiv:1306.4992•Physical Review Letters•Jan 28, 2014•146 citations

LOSS IN SUPERCONDUCTING QUANTUM DEVICES FROM NON-EQUILIBRIUM QUASIPARTICLES AND INHOMOGENEITY IN ENERGY GAP

Rui Zhang

This dissertation describes energy dissipation and microwave loss due to non-equilibrium quasiparticles in superconducting transmon qubits and titanium nitride coplanar waveguide resonators. During the measurements of transmon T1 relaxation time and resonator quality factor QI, I observed reduced microwave loss as the temperature increased from 20 mK to approximately Tc/10 at which the loss takes on a minimum value. I argue that this effect is due to non-equilibrium quasiparticles. I measured the temperature dependence of the relaxation time T1 of the excited state of an Al/AlOx/Al transmon and found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK with a best T1 of 0.2 ms. I present an argument showing this unexpected temperature dependence occurs due to the behavior of non-equilibrium quasiparticles in devices in which one electrode in the tunnel junction has a smaller volume, and slightly smaller superconducting energy gap, than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with the smaller gap, leading to a relatively high density of quasiparticles at the junction and a short T1. Increasing the temperature gives the quasiparticles enough thermal energy to occupy the higher gap electrode, reducing the density at the junction and increasing T1. I present a model of this effect, extract the density of quasiparticles and the two superconducting energy gaps, and discuss implications for increasing the relaxation time of transmons. I also observed a similar phenomenon in low temperature microwave studies of titanium nitride coplanar waveguide resonators. I report on loss in a resonator at temperatures from 20 mK up to 1.1 K and with the application of infrared pair breaking radiation (λ=1.55 μm). With no applied IR light, the internal quality factor increased from QI = 800,000 at T < 70 mK up to QI=(2×10^6 ) at 600 mK. The resonant frequency f0 increased by 2 parts per million over the same temperature range. Above 600 mK both QI and f0 decreased rapidly, consistent with the increase in the density of thermally generated quasiparticles. With the application of IR light and for intensities below 1 aW μm^(-2) and T < 400 mK, QI increased in a similar way to increasing the temperature before beginning to decrease with larger intensities. I show that a model involving non-equilibrium quasiparticles and two regions of different superconducting gaps can explain this unexpected behavior.

•Jan 1, 2020•2 citations

Electrothermal feedback in kinetic inductance detectors

Tejas Guruswamy, Christopher N. Thomas, S Withington +1 more

Abstract In kinetic inductance detectors (KIDs) and other similar applications of superconducting microresonators, both the large and small-signal behaviour of the device may be affected by electrothermal feedback. Microwave power applied to read out the device is absorbed by and heats the superconductor quasiparticles, changing the superconductor conductivity and hence the readout power absorbed in a positive or negative feedback loop. In this work, we explore numerically the implications of an extensible theoretical model of a generic superconducting microresonator device for a typical KID, incorporating recent work on the power flow between superconductor quasiparticles and phonons. This model calculates the large-signal (changes in operating point) and small-signal behaviour of a device, allowing us to determine the effect of electrothermal feedback on device responsivity and noise characteristics under various operating conditions. We also investigate how thermally isolating the device from the bath, for example by designing the device on a membrane only connected to the bulk substrate by thin legs, affects device performance. We find that at a typical device operating point, positive electrothermal feedback reduces the effective thermal conductance from the superconductor quasiparticles to the bath, and so increases responsivity to signal (pair-breaking) power, increases noise from temperature fluctuations, and decreases the noise equivalent power (NEP). Similarly, increasing the thermal isolation of the device while keeping the quasiparticle temperature constant decreases the NEP, but also decreases the device response bandwidth.

arXiv:1701.09145•Superconductor Science and Technology•Mar 23, 2017•5 citations
The response of a MoRe-based superconducting resonator operating near 5 K to pulsed infrared irradiation is investigated, and the underlying physical mechanisms are analyzed. The device exhibits a pronounced nonlinear response dominated by nonequilibrium quasiparticle dynamics rather than uniform thermal heating. Infrared pulses produce strong distortions of the resonance curve and a transient decrease in the resonance frequency, consistent with increased kinetic inductance caused by quasiparticle generation. The frequency shift scales approximately linearly with absorbed power, whereas the dissipation response saturates at higher powers, indicating the formation of a nonequilibrium steady-state quasiparticle population. These observations demonstrate a transition from a linear pair-breaking regime to a saturated dissipation regime, likely associated with a quasiparticle relaxation bottleneck or partial suppression of the smaller superconducting gap in MoRe. The results highlight the relevance of nonequilibrium processes in MoRe and confirm its potential for microwave kinetic-inductance detector applications.
In this thesis I describe work on developing theoretical and numerical models of supercon- ducting thin-film microwave resonators. Superconducting resonators are used in a variety of applications, one of which is as kinetic inductance detectors (KIDs). KIDs are ultra-low noise, highly sensitive, multiplexable detectors, with uses in a wide variety of fields including astrophysics, medical imaging, and particle physics. Resonators are also crucial for supercon- ducting qubit readout, superconducting mixers and parametric amplifiers, and as multiplexers for other devices. The results described in this thesis apply to all thin film resonators, but are primarily described in the context of KIDs. I develop models of how constant absorbed power affects superconducting thin films, driving them out of thermal equilibrium with the bath. Using the Chang & Scalapino equations, I calculate numerically the steady-state quasiparticle and phonon distributions for various sources of power (sub-gap and above-gap photons and phonons, single frequency and broadband). Many new results emerge, a few of which are: the quasiparticle heating effects of microwave power, explaining the experimentally measured saturation of resonator performance; the frequency dependence of the quasiparticle generation efficiency in the sub-mm wavelength range; and the importance of phonon trapping in thin films at low temperatures. I then use these nonequilibrium results in higher-level device models. Starting from a generic framework for resonators, I present and implement a model of a KID with variable thermal isolation. I calculate the effects of quasiparticle heating on both the large-signal and small-signal behaviour, highlighting the effects of electrothermal feedback caused by readout power. Electrothermal feedback is shown to be able to increase or decrease the magnitude and bandwidth of the responsivity and noise, depending on the operating point. Finally, I propose an experimental measurement of quasiparticle heating effects in a new device – a four-port ring resonator. In such a device, unlike in the standard two-port resonator, the device can be heated and read out independently. I develop detailed models for the thermal and electrical behaviour of these devices, and suggest a scheme by which the quasiparticle heating effects of microwave power, predicted in this thesis, can be measured.
Superconducting materials are useful for a wide range of applications, ranging from particle detectors to quantum computing. The presence of excitations (quasiparticles) in the superconductor can be a resource in some devices and a disturbance in others - in kinetic inductance detectors, the generation of quasiparticles by an incoming photon can be read out and used to calculate the energy of the photon, while the tunnelling of quasiparticles is a cause of decoherence in quantum computing. While early research mostly focused on superconductors close to the critical temperature, temperatures that are far below the critical temperatures are often used for current applications. At these low temperatures, the energy exchange between quasiparticles and phonons becomes slow, and even small disturbances may drive the energy distribution of the quasiparticles out of thermal equilibrium. In fact, experiments usually show a residual number of quasiparticles even at milikelvin temperatures, for which the thermal density of quasiparticles would be negligible. This thesis consists of two parts: In the first part, I model the energy distribution of quasiparticles in superconducting resonators: Quasiparticles absorb energy by absorbing photons and release it as phonons, which drives the superconductor out of thermal equilibrium. I solve a set of rate equations, both numerical and analytical, to calculate the energy distribution of the quasiparticles. For parameters typically used in kinetic inductance detectors made of aluminum, the microwave signal used to read out the resonator dominates the energy distribution of the quasiparticles, while their density is determined by other processes. At not too low temperatures, quasiparticles are mainly produced by thermal phonons, and my calculations reproduce recently measured quality factors of resonators at temperatures above 250 mK without free parameters. I show that even a very small number of photons of higher energy, which I ascribe to noise from the microwave generator, would dominate the quasiparticle density at lower temperatures. Under this assumption, my calculations also reproduce the quality factors at lower temperatures. In the second part of this thesis, I investigate the effects of spatial fluctuations of the superconducting energy gap on the dynamics of quasiparticles. Recently, it has been proposed that such fluctuations may lead to the localization of quasiparticles in states below the energy gap, which could cause a finite quasiparticle density even at very low temperatures. Using the Keldysh-Usadel formalism, I derive rates for the different processes (recombination/(de-) localization/generation) of quasiparticles in such systems. Using these rate equations I derive new upper limits for the quasiparticle density that could result from these localized states. These upper limits show that localization caused by weak magnetic impurities in typical aluminum systems does not lead to a relevant quasiparticle density. This contradicts previous theories, which only consider the recombination between two localized quasiparticles without examining their dynamics in detail.
Microwave kinetic inductance detectors are typically operated at high readout power to raise the detector signal above system noise. At sufficiently large readout power, the current-dependent kinetic inductance couples the detector response to its readout bias. Using a nonlinear resonator framework and time-domain circuit calculations, we show that the amplitude, shape, and relaxation time of the driven detector's response depend on both the absorbed energy and on the readout bias. Strongly driven bias points produce amplified, extended, and non-exponential pulse responses. Qualitative agreement between calculated and measured pulse responses indicates that these effects are dominated by the driven nonlinear resonator dynamics rather than by altered quasiparticle dynamics. Beyond resonance bifurcation, sufficiently large pulse events drive the resonator between stable branches, resulting in a metastable latched state which persists after the quasiparticle transient has decayed. The pulse energy required for branch switching is set by the readout bias, suggesting a mode of triggered detection with an in-situ tunable threshold. Although nonlinear operation requires calibration of the bias- and energy-dependent response, the enhanced pulse amplitude and duration, together with tunable latching and the ability to select these parameters via the readout operating state, are likely to be of interest for single-photon and rare-event experiments, especially those limited by amplifier or system noise.
In a superconductor, absorption of photons with an energy below the superconducting gap leads to redistribution of quasiparticles over energy and thus induces a strong nonequilibrium quasiparticle energy distribution. We have measured the electrodynamic response, quality factor, and resonant frequency of a superconducting aluminium microwave resonator as a function of microwave power and temperature. Below 200 mK, both the quality factor and resonant frequency decrease with increasing microwave power, consistent with the creation of excess quasiparticles due to microwave absorption. Counterintuitively, above 200 mK, the quality factor and resonant frequency increase with increasing power. We demonstrate that the effect can only be understood by a nonthermal quasiparticle distribution.
This dissertation describes energy dissipation and microwave loss due to non-equilibrium quasiparticles in superconducting transmon qubits and titanium nitride coplanar waveguide resonators. During the measurements of transmon T1 relaxation time and resonator quality factor QI, I observed reduced microwave loss as the temperature increased from 20 mK to approximately Tc/10 at which the loss takes on a minimum value. I argue that this effect is due to non-equilibrium quasiparticles. I measured the temperature dependence of the relaxation time T1 of the excited state of an Al/AlOx/Al transmon and found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK with a best T1 of 0.2 ms. I present an argument showing this unexpected temperature dependence occurs due to the behavior of non-equilibrium quasiparticles in devices in which one electrode in the tunnel junction has a smaller volume, and slightly smaller superconducting energy gap, than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with the smaller gap, leading to a relatively high density of quasiparticles at the junction and a short T1. Increasing the temperature gives the quasiparticles enough thermal energy to occupy the higher gap electrode, reducing the density at the junction and increasing T1. I present a model of this effect, extract the density of quasiparticles and the two superconducting energy gaps, and discuss implications for increasing the relaxation time of transmons. I also observed a similar phenomenon in low temperature microwave studies of titanium nitride coplanar waveguide resonators. I report on loss in a resonator at temperatures from 20 mK up to 1.1 K and with the application of infrared pair breaking radiation (λ=1.55 μm). With no applied IR light, the internal quality factor increased from QI = 800,000 at T < 70 mK up to QI=(2×10^6 ) at 600 mK. The resonant frequency f0 increased by 2 parts per million over the same temperature range. Above 600 mK both QI and f0 decreased rapidly, consistent with the increase in the density of thermally generated quasiparticles. With the application of IR light and for intensities below 1 aW μm^(-2) and T < 400 mK, QI increased in a similar way to increasing the temperature before beginning to decrease with larger intensities. I show that a model involving non-equilibrium quasiparticles and two regions of different superconducting gaps can explain this unexpected behavior.
Abstract In kinetic inductance detectors (KIDs) and other similar applications of superconducting microresonators, both the large and small-signal behaviour of the device may be affected by electrothermal feedback. Microwave power applied to read out the device is absorbed by and heats the superconductor quasiparticles, changing the superconductor conductivity and hence the readout power absorbed in a positive or negative feedback loop. In this work, we explore numerically the implications of an extensible theoretical model of a generic superconducting microresonator device for a typical KID, incorporating recent work on the power flow between superconductor quasiparticles and phonons. This model calculates the large-signal (changes in operating point) and small-signal behaviour of a device, allowing us to determine the effect of electrothermal feedback on device responsivity and noise characteristics under various operating conditions. We also investigate how thermally isolating the device from the bath, for example by designing the device on a membrane only connected to the bulk substrate by thin legs, affects device performance. We find that at a typical device operating point, positive electrothermal feedback reduces the effective thermal conductance from the superconductor quasiparticles to the bath, and so increases responsivity to signal (pair-breaking) power, increases noise from temperature fluctuations, and decreases the noise equivalent power (NEP). Similarly, increasing the thermal isolation of the device while keeping the quasiparticle temperature constant decreases the NEP, but also decreases the device response bandwidth.