Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

LOSS IN SUPERCONDUCTING QUANTUM DEVICES FROM NON-EQUILIBRIUM QUASIPARTICLES AND INHOMOGENEITY IN ENERGY GAP

Rui Zhang

Published Jan 1, 2020• 1 citation
Publisher

Abstract

This dissertation describes energy dissipation and microwave loss due to non-equilibrium quasiparticles in superconducting transmon qubits and titanium nitride coplanar waveguide resonators. During the measurements of transmon T1 relaxation time and resonator quality factor QI, I observed reduced microwave loss as the temperature increased from 20 mK to approximately Tc/10 at which the loss takes on a minimum value. I argue that this effect is due to non-equilibrium quasiparticles. I measured the temperature dependence of the relaxation time T1 of the excited state of an Al/AlOx/Al transmon and found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK with a best T1 of 0.2 ms. I present an argument showing this unexpected temperature dependence occurs due to the behavior of non-equilibrium quasiparticles in devices in which one electrode in the tunnel junction has a smaller volume, and slightly smaller superconducting energy gap, than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with the smaller gap, leading to a relatively high density of quasiparticles at the junction and a short T1. Increasing the temperature gives the quasiparticles enough thermal energy to occupy the higher gap electrode, reducing the density at the junction and increasing T1. I present a model of this effect, extract the density of quasiparticles and the two superconducting energy gaps, and discuss implications for increasing the relaxation time of transmons. I also observed a similar phenomenon in low temperature microwave studies of titanium nitride coplanar waveguide resonators. I report on loss in a resonator at temperatures from 20 mK up to 1.1 K and with the application of infrared pair breaking radiation (λ=1.55 μm). With no applied IR light, the internal quality factor increased from QI = 800,000 at T < 70 mK up to QI=(2×10^6 ) at 600 mK. The resonant frequency f0 increased by 2 parts per million over the same temperature range. Above 600 mK both QI and f0 decreased rapidly, consistent with the increase in the density of thermally generated quasiparticles. With the application of IR light and for intensities below 1 aW μm^(-2) and T < 400 mK, QI increased in a similar way to increasing the temperature before beginning to decrease with larger intensities. I show that a model involving non-equilibrium quasiparticles and two regions of different superconducting gaps can explain this unexpected behavior.

DOI
10.13016/c516-gizd

Related papers

Nonequilibrium quasiparticles in superconducting circuits: Energy relaxation and charge and flux noise

José Alberto Nava Aquino, Rogério de Sousa

The quasiparticle density observed in low-temperature superconducting circuits is several orders of magnitude larger than the value expected at thermal equilibrium. The tunneling of this excess of quasiparticles across Josephson junctions is recognized as one of the main loss and decoherence mechanisms in superconducting qubits. Here we present a unified impedance theory that accounts for quasiparticle energy loss in circuit regions both far from and near to (across) junctions. Our theory leverages the recent experimental demonstration that the excess quasiparticles are in quasiequilibrium [Connolly et al., Phys. Rev. Lett. 132, 217001 (2024)] and uses a generalized fluctuation-dissipation theorem to predict the amount of charge and flux noise generated by them. We compute the resulting energy relaxation time ${T}_{1}$ in transmon qubits with and without junction asymmetric gap engineering, and show that quasiparticles residing away from junctions can play a dominant role in the former case. They also may provide an upper limit for resonator quality factors if the density of amorphous two-level systems is reduced. In addition, we show that charge noise from quasiparticles leads to flux noise that is logarithmic in frequency, giving rise to a ``nearly white'' contribution that is comparable to the flux noise observed in flux qubits. This contrasts with amorphous two-level systems, whose associated flux noise is shown to be super-Ohmic. We discuss how this quasiparticle flux noise can limit ${T}_{2}^{\ensuremath{\ast}}$ coherence times in flux-tunable qubits. The final conclusion is that asymmetric gap engineering can greatly reduce noise and increase coherence times in superconducting qubits.

arXiv:2407.21177•Physical Review Applied•Sep 18, 2025•2 citations

Power and temperature dependent model for high Q superconductor resonators

Ashish Alexander, Christopher Weddle, Christopher J. K. Richardson

Measuring the internal quality factor of coplanar waveguide superconducting resonators is an established method of determining small losses in superconducting devices. Often, resonator losses are attributed to two-level system (TLS) defects using a power dependent model for the quality factor. However, excess non-equilibrium quasiparticles can also limit the quality factor of superconducting resonators. Here, a two-temperature, power and temperature dependent model is used to evaluate resonator losses for titanium nitride and aluminum coplanar waveguide resonators with loss tangents of 10−5–10−6. This model enables a set of parameters to describe both the internal quality factor and fractional frequency shift of the resonator across a broad range of average cavity photon numbers, from 1 to 106, and temperatures between those limited by the experimental apparatus near 50 mK and thermal quasiparticle dominated. The presented model also offers potential insight into observing the temperature and power dependence of TLS–TLS interactions in these resonators.

arXiv:2205.06291•APL Quantum•Jul 23, 2025•4 citations

Non-equilibrium superconductivity in quantum-sensing superconducting resonators

D J Goldie, S Withington

Low temperature microwave superconducting resonators (SRs) are attractive candidates for producing quantum-sensitive, arrayable energy or power detectors for astrophysical and other precision measurement applications. Their readout uses a microwave probe signal with quanta of energy well below the threshold for pair-breaking in the superconductor. We have calculated the non-equilibrium quasiparticle and phonon distributions generated by the photons of the probe signal of a resonator operating well below its superconducting transition temperature T c as the absorbed probe power was changed using the coupled kinetic equations described by Chang and Scalapino. The calculations give insight into a rate equation estimate which suggests that the quasiparticle distributions can be driven far from their thermal equilibrium value for typical readout powers. From the driven quasiparticle distribution functions, the driven quasiparticle number densities and lifetimes were calculated. An effective temperature to describe the driven quasiparticles was defined. The non-equilibrium lifetimes were compared to the distribution-averaged thermal lifetimes at the effective temperature and good agreement was found typically within a few per cent. We used the non-equilibrium quasiparticle distribution to model a representative SR. The complex conductivity and hence the frequency dependence of the experimentally measured forward scattering parameter S 21 of the SR as a function of absorbed power were found. The non-equilibrium S 21 cannot be accurately modeled by a thermal distribution even at its own elevated temperature, having a higher quality factor in all cases studied, although for low absorbed powers the two effective temperatures are similar. From the non-equilibrium lifetimes and number densities we determined the achievable noise equivalent power (NEP) of the resonator used as a power detector as a function of absorbed microwave power. Simpler expressions to evaluate the effective quasiparticle temperature as a function of absorbed power have also been derived. We conclude that multiple photon absorption from the microwave probe increases the quasiparticle number above the thermal background and ultimately limits the achievable NEP of the resonator at temperatures well below T c .

arXiv:1208.0685•Superconductor Science and Technology•Nov 8, 2012•60 citations

Modeling the dynamics of quasiparticles in superconducting devices at low temperatures

Fischer, Paul Benedikt

Superconducting materials are useful for a wide range of applications, ranging from particle detectors to quantum computing. The presence of excitations (quasiparticles) in the superconductor can be a resource in some devices and a disturbance in others - in kinetic inductance detectors, the generation of quasiparticles by an incoming photon can be read out and used to calculate the energy of the photon, while the tunnelling of quasiparticles is a cause of decoherence in quantum computing. While early research mostly focused on superconductors close to the critical temperature, temperatures that are far below the critical temperatures are often used for current applications. At these low temperatures, the energy exchange between quasiparticles and phonons becomes slow, and even small disturbances may drive the energy distribution of the quasiparticles out of thermal equilibrium. In fact, experiments usually show a residual number of quasiparticles even at milikelvin temperatures, for which the thermal density of quasiparticles would be negligible. This thesis consists of two parts: In the first part, I model the energy distribution of quasiparticles in superconducting resonators: Quasiparticles absorb energy by absorbing photons and release it as phonons, which drives the superconductor out of thermal equilibrium. I solve a set of rate equations, both numerical and analytical, to calculate the energy distribution of the quasiparticles. For parameters typically used in kinetic inductance detectors made of aluminum, the microwave signal used to read out the resonator dominates the energy distribution of the quasiparticles, while their density is determined by other processes. At not too low temperatures, quasiparticles are mainly produced by thermal phonons, and my calculations reproduce recently measured quality factors of resonators at temperatures above 250 mK without free parameters. I show that even a very small number of photons of higher energy, which I ascribe to noise from the microwave generator, would dominate the quasiparticle density at lower temperatures. Under this assumption, my calculations also reproduce the quality factors at lower temperatures. In the second part of this thesis, I investigate the effects of spatial fluctuations of the superconducting energy gap on the dynamics of quasiparticles. Recently, it has been proposed that such fluctuations may lead to the localization of quasiparticles in states below the energy gap, which could cause a finite quasiparticle density even at very low temperatures. Using the Keldysh-Usadel formalism, I derive rates for the different processes (recombination/(de-) localization/generation) of quasiparticles in such systems. Using these rate equations I derive new upper limits for the quasiparticle density that could result from these localized states. These upper limits show that localization caused by weak magnetic impurities in typical aluminum systems does not lead to a relevant quasiparticle density. This contradicts previous theories, which only consider the recombination between two localized quasiparticles without examining their dynamics in detail.

•Jan 1, 2025•0 citations

Effects of Optical Illumination on Superconducting Quantum Devices

Rangga P. Budoyo

I report measurements of two different types of superconducting devices illuminated by 780 nm light, one of the wavelengths needed in a proposed atom-superconductor hybrid quantum system. I illuminated a thin-film Al lumped-element resonator and observed the resonator quality factor and resonance frequency as a function of illumination intensity, microwave power, and temperature. The resonator was mounted in a 3d aluminum cavity. The variation in optically-induced loss due to microwave power was similar to the behavior expected for loss from a distribution of two-level systems. Although this behavior may suggest the presence of optically activated two-level systems, I found that the loss is better explained by the presence of nonequilibrium quasiparticles generated by the illumination and excited by the microwave drive. I described a model of the system where optical absorption creates an effective source of phonons and solved the coupled quasiparticle-phonon rate equations. I found good agreement between the simulation and the measured resonator quality factor and frequency shift as a function of temperature, microwave power, and optical illumination. I fabricated a transmon qubit and studied the qubit transition frequency and relaxation time as a function of illumination intensity and temperature. The qubit was mounted in a 3d aluminum cavity and coupled to the cavity forming a Jaynes-Cummings system. Qubit relaxation showed non-exponential behavior that I fit to a quasiparticle fluctuation model with two characteristic times. The transition frequency and both characteristic times decreased with increasing illumination intensity. For comparison, I described a nonequilibrium quasiparticle model for the expected frequency shift and relaxation time due to quasiparticle tunneling through the Josephson junction. While the quasiparticle simulation predicted the general qualitative behavior of the frequency shift and relaxation time, there were some significant discrepancies with the data. This suggests the model needs to be extended, for example by including a different gap in the two superconductor layers forming the junction, and by taking into account other possible sources of loss and decoherence.

•Jan 1, 2015•2 citations

SPECTROSCOPY OF TWO LEVEL DEFECTS & QUASIPARTICLES IN SUPERCONDUCTING RESONATORS

Timothy Kohler

Superconducting films are inherently limited by losses due to two-level system (TLS) defects within the amorphous oxide layers surrounding them and from quasiparticles in the film. In this thesis I will discuss novel theoretical and experimental methods toward understanding superconducting resonator loss from deleterious surface TLS defects as well as a loss transition from non-equilibrium quasiparticles in granular TiN. I will show using finite element solver software that a resonator with submicron linewidth and linespacing can be used to better characterize and simulate surface TLS as part of a circuit QED system. I have observed individual surface TLS and found coupling values in the range of g/2π =50 kHz -280 kHz with a maximum dipole moment pz-max = 4.5 Debye (.93 eÅ). I have found in in simulation of experiment that over 80% of the strongly coupled TLS reside within 50 nm of the corner between the Metal-Substrate (MS) and Substrate-Air (SA) interface. Additionally I have studied a loss transition from non-equilibrium quasiparticles in TiN films. These films exhibit an anomalous loss dependence on substrate treatment and film thickness. The films of interest are ones grown thin on oxidized substrates, which exhibit an order of magnitude decrease in internal quality factor (Qi) relative to either thicker ˝films or films grown without the oxidized substrate. These films additionally exhibit a grain size on average of 7.5 nm, a higher inhomogeneous gap, a transition to lower stress and a preference for the [111] crystal growth. The temperature dependence of the conductivity is fit and a factor of two difference in quasiparticle lifetime is found between the two films where the thinner film has a shorter lifetime. A two gap quasiparticle trapping model is fit to the temperature dependent loss data. The data is consistent with a model where non-equilibrium quasi-particles are trapped in low gapped grains on the inside of the films. From these works and others presented in my thesis the understanding of TLSs on surfaces and non-equilibrium quasiparticles in TiN has improved. This will help illuminate some of the most important absorption mechanisms plaguing superconducting qubits and resonators.

•Jan 1, 2021•0 citations
This dissertation describes energy dissipation and microwave loss due to non-equilibrium quasiparticles in superconducting transmon qubits and titanium nitride coplanar waveguide resonators. During the measurements of transmon T1 relaxation time and resonator quality factor QI, I observed reduced microwave loss as the temperature increased from 20 mK to approximately Tc/10 at which the loss takes on a minimum value. I argue that this effect is due to non-equilibrium quasiparticles. I measured the temperature dependence of the relaxation time T1 of the excited state of an Al/AlOx/Al transmon and found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK with a best T1 of 0.2 ms. I present an argument showing this unexpected temperature dependence occurs due to the behavior of non-equilibrium quasiparticles in devices in which one electrode in the tunnel junction has a smaller volume, and slightly smaller superconducting energy gap, than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with the smaller gap, leading to a relatively high density of quasiparticles at the junction and a short T1. Increasing the temperature gives the quasiparticles enough thermal energy to occupy the higher gap electrode, reducing the density at the junction and increasing T1. I present a model of this effect, extract the density of quasiparticles and the two superconducting energy gaps, and discuss implications for increasing the relaxation time of transmons. I also observed a similar phenomenon in low temperature microwave studies of titanium nitride coplanar waveguide resonators. I report on loss in a resonator at temperatures from 20 mK up to 1.1 K and with the application of infrared pair breaking radiation (λ=1.55 μm). With no applied IR light, the internal quality factor increased from QI = 800,000 at T < 70 mK up to QI=(2×10^6 ) at 600 mK. The resonant frequency f0 increased by 2 parts per million over the same temperature range. Above 600 mK both QI and f0 decreased rapidly, consistent with the increase in the density of thermally generated quasiparticles. With the application of IR light and for intensities below 1 aW μm^(-2) and T < 400 mK, QI increased in a similar way to increasing the temperature before beginning to decrease with larger intensities. I show that a model involving non-equilibrium quasiparticles and two regions of different superconducting gaps can explain this unexpected behavior.
The quasiparticle density observed in low-temperature superconducting circuits is several orders of magnitude larger than the value expected at thermal equilibrium. The tunneling of this excess of quasiparticles across Josephson junctions is recognized as one of the main loss and decoherence mechanisms in superconducting qubits. Here we present a unified impedance theory that accounts for quasiparticle energy loss in circuit regions both far from and near to (across) junctions. Our theory leverages the recent experimental demonstration that the excess quasiparticles are in quasiequilibrium [Connolly et al., Phys. Rev. Lett. 132, 217001 (2024)] and uses a generalized fluctuation-dissipation theorem to predict the amount of charge and flux noise generated by them. We compute the resulting energy relaxation time T1{T}_{1}T1​ in transmon qubits with and without junction asymmetric gap engineering, and show that quasiparticles residing away from junctions can play a dominant role in the former case. They also may provide an upper limit for resonator quality factors if the density of amorphous two-level systems is reduced. In addition, we show that charge noise from quasiparticles leads to flux noise that is logarithmic in frequency, giving rise to a ``nearly white'' contribution that is comparable to the flux noise observed in flux qubits. This contrasts with amorphous two-level systems, whose associated flux noise is shown to be super-Ohmic. We discuss how this quasiparticle flux noise can limit ${T}_{2}^{\ensuremath{\ast}}$ coherence times in flux-tunable qubits. The final conclusion is that asymmetric gap engineering can greatly reduce noise and increase coherence times in superconducting qubits.
Measuring the internal quality factor of coplanar waveguide superconducting resonators is an established method of determining small losses in superconducting devices. Often, resonator losses are attributed to two-level system (TLS) defects using a power dependent model for the quality factor. However, excess non-equilibrium quasiparticles can also limit the quality factor of superconducting resonators. Here, a two-temperature, power and temperature dependent model is used to evaluate resonator losses for titanium nitride and aluminum coplanar waveguide resonators with loss tangents of 10−5–10−6. This model enables a set of parameters to describe both the internal quality factor and fractional frequency shift of the resonator across a broad range of average cavity photon numbers, from 1 to 106, and temperatures between those limited by the experimental apparatus near 50 mK and thermal quasiparticle dominated. The presented model also offers potential insight into observing the temperature and power dependence of TLS–TLS interactions in these resonators.
Low temperature microwave superconducting resonators (SRs) are attractive candidates for producing quantum-sensitive, arrayable energy or power detectors for astrophysical and other precision measurement applications. Their readout uses a microwave probe signal with quanta of energy well below the threshold for pair-breaking in the superconductor. We have calculated the non-equilibrium quasiparticle and phonon distributions generated by the photons of the probe signal of a resonator operating well below its superconducting transition temperature T c as the absorbed probe power was changed using the coupled kinetic equations described by Chang and Scalapino. The calculations give insight into a rate equation estimate which suggests that the quasiparticle distributions can be driven far from their thermal equilibrium value for typical readout powers. From the driven quasiparticle distribution functions, the driven quasiparticle number densities and lifetimes were calculated. An effective temperature to describe the driven quasiparticles was defined. The non-equilibrium lifetimes were compared to the distribution-averaged thermal lifetimes at the effective temperature and good agreement was found typically within a few per cent. We used the non-equilibrium quasiparticle distribution to model a representative SR. The complex conductivity and hence the frequency dependence of the experimentally measured forward scattering parameter S 21 of the SR as a function of absorbed power were found. The non-equilibrium S 21 cannot be accurately modeled by a thermal distribution even at its own elevated temperature, having a higher quality factor in all cases studied, although for low absorbed powers the two effective temperatures are similar. From the non-equilibrium lifetimes and number densities we determined the achievable noise equivalent power (NEP) of the resonator used as a power detector as a function of absorbed microwave power. Simpler expressions to evaluate the effective quasiparticle temperature as a function of absorbed power have also been derived. We conclude that multiple photon absorption from the microwave probe increases the quasiparticle number above the thermal background and ultimately limits the achievable NEP of the resonator at temperatures well below T c .
Superconducting materials are useful for a wide range of applications, ranging from particle detectors to quantum computing. The presence of excitations (quasiparticles) in the superconductor can be a resource in some devices and a disturbance in others - in kinetic inductance detectors, the generation of quasiparticles by an incoming photon can be read out and used to calculate the energy of the photon, while the tunnelling of quasiparticles is a cause of decoherence in quantum computing. While early research mostly focused on superconductors close to the critical temperature, temperatures that are far below the critical temperatures are often used for current applications. At these low temperatures, the energy exchange between quasiparticles and phonons becomes slow, and even small disturbances may drive the energy distribution of the quasiparticles out of thermal equilibrium. In fact, experiments usually show a residual number of quasiparticles even at milikelvin temperatures, for which the thermal density of quasiparticles would be negligible. This thesis consists of two parts: In the first part, I model the energy distribution of quasiparticles in superconducting resonators: Quasiparticles absorb energy by absorbing photons and release it as phonons, which drives the superconductor out of thermal equilibrium. I solve a set of rate equations, both numerical and analytical, to calculate the energy distribution of the quasiparticles. For parameters typically used in kinetic inductance detectors made of aluminum, the microwave signal used to read out the resonator dominates the energy distribution of the quasiparticles, while their density is determined by other processes. At not too low temperatures, quasiparticles are mainly produced by thermal phonons, and my calculations reproduce recently measured quality factors of resonators at temperatures above 250 mK without free parameters. I show that even a very small number of photons of higher energy, which I ascribe to noise from the microwave generator, would dominate the quasiparticle density at lower temperatures. Under this assumption, my calculations also reproduce the quality factors at lower temperatures. In the second part of this thesis, I investigate the effects of spatial fluctuations of the superconducting energy gap on the dynamics of quasiparticles. Recently, it has been proposed that such fluctuations may lead to the localization of quasiparticles in states below the energy gap, which could cause a finite quasiparticle density even at very low temperatures. Using the Keldysh-Usadel formalism, I derive rates for the different processes (recombination/(de-) localization/generation) of quasiparticles in such systems. Using these rate equations I derive new upper limits for the quasiparticle density that could result from these localized states. These upper limits show that localization caused by weak magnetic impurities in typical aluminum systems does not lead to a relevant quasiparticle density. This contradicts previous theories, which only consider the recombination between two localized quasiparticles without examining their dynamics in detail.
I report measurements of two different types of superconducting devices illuminated by 780 nm light, one of the wavelengths needed in a proposed atom-superconductor hybrid quantum system. I illuminated a thin-film Al lumped-element resonator and observed the resonator quality factor and resonance frequency as a function of illumination intensity, microwave power, and temperature. The resonator was mounted in a 3d aluminum cavity. The variation in optically-induced loss due to microwave power was similar to the behavior expected for loss from a distribution of two-level systems. Although this behavior may suggest the presence of optically activated two-level systems, I found that the loss is better explained by the presence of nonequilibrium quasiparticles generated by the illumination and excited by the microwave drive. I described a model of the system where optical absorption creates an effective source of phonons and solved the coupled quasiparticle-phonon rate equations. I found good agreement between the simulation and the measured resonator quality factor and frequency shift as a function of temperature, microwave power, and optical illumination. I fabricated a transmon qubit and studied the qubit transition frequency and relaxation time as a function of illumination intensity and temperature. The qubit was mounted in a 3d aluminum cavity and coupled to the cavity forming a Jaynes-Cummings system. Qubit relaxation showed non-exponential behavior that I fit to a quasiparticle fluctuation model with two characteristic times. The transition frequency and both characteristic times decreased with increasing illumination intensity. For comparison, I described a nonequilibrium quasiparticle model for the expected frequency shift and relaxation time due to quasiparticle tunneling through the Josephson junction. While the quasiparticle simulation predicted the general qualitative behavior of the frequency shift and relaxation time, there were some significant discrepancies with the data. This suggests the model needs to be extended, for example by including a different gap in the two superconductor layers forming the junction, and by taking into account other possible sources of loss and decoherence.
Superconducting films are inherently limited by losses due to two-level system (TLS) defects within the amorphous oxide layers surrounding them and from quasiparticles in the film. In this thesis I will discuss novel theoretical and experimental methods toward understanding superconducting resonator loss from deleterious surface TLS defects as well as a loss transition from non-equilibrium quasiparticles in granular TiN. I will show using finite element solver software that a resonator with submicron linewidth and linespacing can be used to better characterize and simulate surface TLS as part of a circuit QED system. I have observed individual surface TLS and found coupling values in the range of g/2π =50 kHz -280 kHz with a maximum dipole moment pz-max = 4.5 Debye (.93 eÅ). I have found in in simulation of experiment that over 80% of the strongly coupled TLS reside within 50 nm of the corner between the Metal-Substrate (MS) and Substrate-Air (SA) interface. Additionally I have studied a loss transition from non-equilibrium quasiparticles in TiN films. These films exhibit an anomalous loss dependence on substrate treatment and film thickness. The films of interest are ones grown thin on oxidized substrates, which exhibit an order of magnitude decrease in internal quality factor (Qi) relative to either thicker ˝films or films grown without the oxidized substrate. These films additionally exhibit a grain size on average of 7.5 nm, a higher inhomogeneous gap, a transition to lower stress and a preference for the [111] crystal growth. The temperature dependence of the conductivity is fit and a factor of two difference in quasiparticle lifetime is found between the two films where the thinner film has a shorter lifetime. A two gap quasiparticle trapping model is fit to the temperature dependent loss data. The data is consistent with a model where non-equilibrium quasi-particles are trapped in low gapped grains on the inside of the films. From these works and others presented in my thesis the understanding of TLSs on surfaces and non-equilibrium quasiparticles in TiN has improved. This will help illuminate some of the most important absorption mechanisms plaguing superconducting qubits and resonators.