Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2508.03434 · APL Quantum

Characterizing and mitigating flux crosstalk in superconducting qubits–couplers system

Myrron Albert Callera Aguila, N. Li, Chen-Hsun Ma, Li-Chieh Hsiao, Yi-Shiang Huang, Yen-Chun Chen, Teik‐Hui Lee, C. F. Chang, Jyh-Yang Wang, S. Y. Huang, Hsi‐Sheng Goan, Chiao-Hsuan Wang, Cen-Shawn Wu, Chii-Dong Chen, Chung-Ting Ke

Published Feb 18, 2026• 5 citations
arXivHTMLPDF

Abstract

Superconducting qubits have achieved exceptional gate fidelities, exceeding the error-correction threshold in recent years. One key ingredient of such improvement is the introduction of tunable couplers to control the qubit-to-qubit coupling through frequency tuning. Moving toward fault-tolerant quantum computation, increasing the number of physical qubits is another step toward effective error correction codes. Under a multiqubit architecture, flux control (Z) lines are crucial in tuning the frequency of the qubits and couplers. However, dense flux lines result in magnetic flux crosstalk, wherein magnetic flux applied to one element inadvertently affects neighboring qubits or couplers. This crosstalk obscures the idle frequency of the qubit when flux bias is applied, which degrades gate performance and calibration accuracy. In this study, we characterize flux crosstalk and suppress it in a multiqubit-coupler chip with multi-Z lines without adding additional readout for couplers. By quantifying the mutual flux-induced frequency shifts of qubits and couplers, we construct a cancellation matrix that enables precise compensation of non-local flux, demonstrating a substantial reduction in Z-line crosstalk from 56.5‰ to 0.13‰, which is close to statistical error. Flux compensation corrects the CZ SWAP measurement, leading to a symmetric map with respect to flux bias. Compared with a crosstalk-free calculated CZ SWAP map, the measured map indicates that our approach provides a near-zero crosstalk for the coupler-transmon system. These results highlight the effectiveness of our approach in enhancing flux crosstalk-free control and supporting its potential for scaling superconducting quantum processors.

DOI
10.1063/5.0295174

Related papers

Flux Crosstalk Calibration from Zero Knowledge to High Precision in Fully Tunable Superconducting Circuits

Y. Gao, Asier Galicia, J. R. Guimarães +9 more

Precise and independent flux control is essential for scalable superconducting processors built from frequency-tunable qubits and couplers, but flux crosstalk undermines it. Conventional calibration methods rely either on dedicated readout channels, which tunable couplers typically lack, or on readout schemes requiring extensive prior spectroscopy of the qubit and coupler. We demonstrate two independent methods that characterize coupler flux crosstalk without directly driving or measuring the couplers. The first method is zero-knowledge characterization, which exploits intrinsic coupler-resonator coupling to yield rapid and accurate estimates with no prior qubit or coupler spectroscopy, accelerating large scale bring-up. The second method is symmetric branch cancellation, which isolates crosstalk from other dispersive effects allowing for quantifying with high precision. Combined with an improved iterative procedure, these methods suppress residual coupler crosstalk below $5\times10^{-5}$, providing a complete route from zero-knowledge initialization to high-precision crosstalk characterization in fully tunable architectures.

arXiv:2611.06656•Nov 4, 2026•0 citations

Learning-Based Calibration of Flux Crosstalk in Transmon Qubit Arrays

Cora N. Barrett, Amir H. Karamlou, Sarah E. Muschinske +13 more

Superconducting quantum processors comprising flux-tunable data and coupler qubits are a promising platform for quantum computation. However, magnetic flux crosstalk between the flux-control lines and the constituent qubits impedes precision control of qubit frequencies, presenting a challenge to scaling this platform. In order to implement high-fidelity digital and analog quantum operations, one must characterize the flux crosstalk and compensate for it. In this work, we introduce a learning-based calibration protocol and demonstrate its experimental performance by calibrating an array of 16 flux-tunable transmon qubits. To demonstrate the extensibility of our protocol, we simulate the crosstalk matrix learning procedure for larger arrays of transmon qubits. We observe an empirically linear scaling in calibration time with system size while maintaining a median qubit frequency error below 300 kHz.

arXiv:2303.03347•Physical Review Applied•Aug 28, 2023•25 citations

Inherent flux crosstalk and coupler-driven single-qubit gates in superconducting circuits

Balázs Gulácsi, Guido Burkard

Crosstalk refers to unwanted qubit addressing. This is particularly detrimental when scaling up quantum information systems because unintended interactions limit their overall performance. For superconducting qubits, tunable couplings and frequency tunability achieved through externally applied magnetic fluxes enable high-fidelity entangling gates; however, they also introduce crosstalk through unintended flux coupling. In this work, we investigate the impact of time-dependent external magnetic fluxes in quantized circuits on superconducting qubit couplings. We find that non-trivial cross-voltage driving emerges between capacitively linked qubits when the magnetic flux threading the SQUID loop of a qubit varies in time, in a manner analogous to Faraday's law of induction. Crucially, we show that this effect enables fast single qubit control through the coupler element in standard tunable-coupler architectures, potentially eliminating the need for individual microwave $XY$ control lines.

quant-pharXiv:2606.10970•Physical Review Applied•Jun 10, 2026•0 citations

Quantum Crosstalk Analysis for Simultaneous Gate Operations on Superconducting Qubits

Peng Zhao, Kehuan Linghu, Zhiyuan Li +5 more

Maintaining or even improving gate performance with growing numbers of parallel controlled qubits is a vital requirement for fault-tolerant quantum computing.For superconducting quantum processors, though isolated one-or two-qubit gates have been demonstrated with high fidelity, implementing these gates in parallel commonly shows worse performance.Generally, this degradation is attributed to various crosstalks between qubits, such as quantum crosstalk due to residual inter-qubit coupling.An understanding of the exact nature of these crosstalks is critical to figuring out respective mitigation schemes and improved qubit architecture designs with low crosstalk.Here we give a theoretical analysis of quantum crosstalk impact on simultaneous gate operations in a qubit architecture, where fixed-frequency transmon qubits are coupled via a tunable bus, and sub-100-ns controlled-Z (CZ) gates can be realized by applying a baseband flux pulse on the bus.Our analysis shows that for microwave-driven single-qubit gates, the dressing from the qubit-qubit coupling can cause non-negligible cross-driving errors when qubits operate near frequency collision regions.During CZ gate operations, although unwanted nearest-neighbor interactions are nominally turned off, sub-MHz parasitic next-nearest-neighbor interactions involving spectator qubits can still exist, causing considerable leakage or control error when one operates qubit systems around these parasitic resonance points.To ensure high-fidelity simultaneous operations, a request could be raised to figure out a better way to balance the gate error from target qubit systems themselves and the error from nonparticipating spectator qubits.Overall, our analysis suggests that towards useful quantum processors, the qubit architecture should be examined carefully in the context of high-fidelity simultaneous gate operations in a scalable qubit lattice.

arXiv:2110.12570•PRX Quantum•Apr 1, 2022•133 citations

High-precision pulse calibration of tunable couplers for high-fidelity two-qubit gates in superconducting quantum processors

Tian-Ming Li, Jiachi Zhang, Bing-Jie Chen +23 more

For superconducting quantum processors, stable high-fidelity two-qubit operations depend on precise flux control of the tunable coupler. However, the pulse distortion poses a significant challenge to the control precision. Current calibration methods, which often rely on microwave crosstalk or additional readout resonators for coupler excitation and readout, tend to be cumbersome and inefficient, especially when couplers only have flux control. Here, we introduce and experimentally validate a pulse calibration scheme that exploits the strong coupling between qubits and couplers, eliminating the need for extra coupler readout and excitation. Our method directly measures the short-time and long-time step responses of the coupler flux pulse transient, enabling us to apply predistortion to subsequent signals using fast Fourier transformation and deconvolution. This approach not only simplifies the calibration process, but also significantly improves the precision and stability of the flux control. We demonstrate the efficacy of our method through the implementation of diabatic controlled-$Z$ (cz) and $i$swap gates with fidelities of $99.61\mathrm{%}\ifmmode\pm\else\textpm\fi{}0.04\mathrm{%}$ and $99.82\mathrm{%}\ifmmode\pm\else\textpm\fi{}0.02\mathrm{%}$, respectively, as well as a series of diabatic controlled-phase gates with high fidelities characterized by cross-entropy benchmarking. The consistency and robustness of our technique are further validated by the reduction in pulse distortion and phase error observed across multilayer cz gates. These results underscore the potential of our calibration and predistortion method to enhance the performance of two-qubit gates in superconducting quantum processors.

arXiv:2410.15041•Physical Review Applied•Feb 21, 2025•22 citations

Crosstalk in Multi-Qubit Fluxonium Architectures with Transmon Couplers

Martijn F. S. Zwanenburg, Christian Kraglund Andersen

In recent years, several architectures have been proposed for implementing two-qubit operations on fluxonium superconducting qubits. A particularly promising approach, which was demonstrated experimentally by Refs. [1,2], employs a transmon superconducting qubit as a tunable coupler between the fluxonium qubits. These experiments have shown that the transmon coupler enables fast, high-fidelity two-qubit operations while suppressing unwanted ZZ crosstalk between the fluxonium qubits. In this work, we numerically study the scalability of this architecture. We find that, when trivially scaling this architecture, crosstalk from spectator qubits limits the gate fidelity to below 90%. We show that these spectator errors can be reduced to below $10^{-4}$ by reducing the coupling strength and by dynamically tuning transmons that are not used for a two-qubit operation to an off position. We further investigate the resilience of the operation to direct capacitive coupling between the transmon couplers and to microwave crosstalk.

quant-pharXiv:2603.09870•Physical Review Applied•Mar 11, 2026•7 citations
Superconducting qubits have achieved exceptional gate fidelities, exceeding the error-correction threshold in recent years. One key ingredient of such improvement is the introduction of tunable couplers to control the qubit-to-qubit coupling through frequency tuning. Moving toward fault-tolerant quantum computation, increasing the number of physical qubits is another step toward effective error correction codes. Under a multiqubit architecture, flux control (Z) lines are crucial in tuning the frequency of the qubits and couplers. However, dense flux lines result in magnetic flux crosstalk, wherein magnetic flux applied to one element inadvertently affects neighboring qubits or couplers. This crosstalk obscures the idle frequency of the qubit when flux bias is applied, which degrades gate performance and calibration accuracy. In this study, we characterize flux crosstalk and suppress it in a multiqubit-coupler chip with multi-Z lines without adding additional readout for couplers. By quantifying the mutual flux-induced frequency shifts of qubits and couplers, we construct a cancellation matrix that enables precise compensation of non-local flux, demonstrating a substantial reduction in Z-line crosstalk from 56.5‰ to 0.13‰, which is close to statistical error. Flux compensation corrects the CZ SWAP measurement, leading to a symmetric map with respect to flux bias. Compared with a crosstalk-free calculated CZ SWAP map, the measured map indicates that our approach provides a near-zero crosstalk for the coupler-transmon system. These results highlight the effectiveness of our approach in enhancing flux crosstalk-free control and supporting its potential for scaling superconducting quantum processors.
Precise and independent flux control is essential for scalable superconducting processors built from frequency-tunable qubits and couplers, but flux crosstalk undermines it. Conventional calibration methods rely either on dedicated readout channels, which tunable couplers typically lack, or on readout schemes requiring extensive prior spectroscopy of the qubit and coupler. We demonstrate two independent methods that characterize coupler flux crosstalk without directly driving or measuring the couplers. The first method is zero-knowledge characterization, which exploits intrinsic coupler-resonator coupling to yield rapid and accurate estimates with no prior qubit or coupler spectroscopy, accelerating large scale bring-up. The second method is symmetric branch cancellation, which isolates crosstalk from other dispersive effects allowing for quantifying with high precision. Combined with an improved iterative procedure, these methods suppress residual coupler crosstalk below 5×10−55\times10^{-5}5×10−5, providing a complete route from zero-knowledge initialization to high-precision crosstalk characterization in fully tunable architectures.
Superconducting quantum processors comprising flux-tunable data and coupler qubits are a promising platform for quantum computation. However, magnetic flux crosstalk between the flux-control lines and the constituent qubits impedes precision control of qubit frequencies, presenting a challenge to scaling this platform. In order to implement high-fidelity digital and analog quantum operations, one must characterize the flux crosstalk and compensate for it. In this work, we introduce a learning-based calibration protocol and demonstrate its experimental performance by calibrating an array of 16 flux-tunable transmon qubits. To demonstrate the extensibility of our protocol, we simulate the crosstalk matrix learning procedure for larger arrays of transmon qubits. We observe an empirically linear scaling in calibration time with system size while maintaining a median qubit frequency error below 300 kHz.
Crosstalk refers to unwanted qubit addressing. This is particularly detrimental when scaling up quantum information systems because unintended interactions limit their overall performance. For superconducting qubits, tunable couplings and frequency tunability achieved through externally applied magnetic fluxes enable high-fidelity entangling gates; however, they also introduce crosstalk through unintended flux coupling. In this work, we investigate the impact of time-dependent external magnetic fluxes in quantized circuits on superconducting qubit couplings. We find that non-trivial cross-voltage driving emerges between capacitively linked qubits when the magnetic flux threading the SQUID loop of a qubit varies in time, in a manner analogous to Faraday's law of induction. Crucially, we show that this effect enables fast single qubit control through the coupler element in standard tunable-coupler architectures, potentially eliminating the need for individual microwave XYXYXY control lines.
Maintaining or even improving gate performance with growing numbers of parallel controlled qubits is a vital requirement for fault-tolerant quantum computing.For superconducting quantum processors, though isolated one-or two-qubit gates have been demonstrated with high fidelity, implementing these gates in parallel commonly shows worse performance.Generally, this degradation is attributed to various crosstalks between qubits, such as quantum crosstalk due to residual inter-qubit coupling.An understanding of the exact nature of these crosstalks is critical to figuring out respective mitigation schemes and improved qubit architecture designs with low crosstalk.Here we give a theoretical analysis of quantum crosstalk impact on simultaneous gate operations in a qubit architecture, where fixed-frequency transmon qubits are coupled via a tunable bus, and sub-100-ns controlled-Z (CZ) gates can be realized by applying a baseband flux pulse on the bus.Our analysis shows that for microwave-driven single-qubit gates, the dressing from the qubit-qubit coupling can cause non-negligible cross-driving errors when qubits operate near frequency collision regions.During CZ gate operations, although unwanted nearest-neighbor interactions are nominally turned off, sub-MHz parasitic next-nearest-neighbor interactions involving spectator qubits can still exist, causing considerable leakage or control error when one operates qubit systems around these parasitic resonance points.To ensure high-fidelity simultaneous operations, a request could be raised to figure out a better way to balance the gate error from target qubit systems themselves and the error from nonparticipating spectator qubits.Overall, our analysis suggests that towards useful quantum processors, the qubit architecture should be examined carefully in the context of high-fidelity simultaneous gate operations in a scalable qubit lattice.
For superconducting quantum processors, stable high-fidelity two-qubit operations depend on precise flux control of the tunable coupler. However, the pulse distortion poses a significant challenge to the control precision. Current calibration methods, which often rely on microwave crosstalk or additional readout resonators for coupler excitation and readout, tend to be cumbersome and inefficient, especially when couplers only have flux control. Here, we introduce and experimentally validate a pulse calibration scheme that exploits the strong coupling between qubits and couplers, eliminating the need for extra coupler readout and excitation. Our method directly measures the short-time and long-time step responses of the coupler flux pulse transient, enabling us to apply predistortion to subsequent signals using fast Fourier transformation and deconvolution. This approach not only simplifies the calibration process, but also significantly improves the precision and stability of the flux control. We demonstrate the efficacy of our method through the implementation of diabatic controlled-ZZZ (cz) and iiiswap gates with fidelities of $99.61\mathrm{%}\ifmmode\pm\else\textpm\fi{}0.04\mathrm{%}$ and $99.82\mathrm{%}\ifmmode\pm\else\textpm\fi{}0.02\mathrm{%}$, respectively, as well as a series of diabatic controlled-phase gates with high fidelities characterized by cross-entropy benchmarking. The consistency and robustness of our technique are further validated by the reduction in pulse distortion and phase error observed across multilayer cz gates. These results underscore the potential of our calibration and predistortion method to enhance the performance of two-qubit gates in superconducting quantum processors.
In recent years, several architectures have been proposed for implementing two-qubit operations on fluxonium superconducting qubits. A particularly promising approach, which was demonstrated experimentally by Refs. [1,2], employs a transmon superconducting qubit as a tunable coupler between the fluxonium qubits. These experiments have shown that the transmon coupler enables fast, high-fidelity two-qubit operations while suppressing unwanted ZZ crosstalk between the fluxonium qubits. In this work, we numerically study the scalability of this architecture. We find that, when trivially scaling this architecture, crosstalk from spectator qubits limits the gate fidelity to below 90%. We show that these spectator errors can be reduced to below 10−410^{-4}10−4 by reducing the coupling strength and by dynamically tuning transmons that are not used for a two-qubit operation to an off position. We further investigate the resilience of the operation to direct capacitive coupling between the transmon couplers and to microwave crosstalk.