Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2502.19818

Low Tc Hafnium Kinetic Inductance Device with High Internal Quality Factor

Xinran Li, Aritoki Suzuki, M. Garcia-Sciveres

Published Feb 27, 2025• 6 citations
arXivHTMLPDF

Abstract

Kinetic inductance devices (KIDs) are superconducting resonators with high kinetic inductance sensitive to external energy perturbations. KIDs made with superconductors having $T_c$ far below one Kelvin are of particular interest for sensing minuscule signals, such as light dark matter detection and millimeter wave telescopes for astronomy and cosmology. In this work, we report the promising performance of KIDs fabricated with Hafnium from heated sputter depositions. The KIDs have $T_c$ lower than 249$\pm$2 mK, the internal quality factor ($Q_i$) of the resonators exceeds $10^5$ and the temperature dependence of the resonances can be described by the generalized Mattis-Bardeen model with a disorder parameter $Γ=4\times10^{-3}Δ_0$. Post-fabrication annealing at temperatures above the deposition temperature can further reduce the $T_c$ and $Γ$ without reducing $Q_i$, leading to improvements in energy resolution.

DOI
10.48550/arxiv.2502.19818

Related papers

Design and performance of hafnium optical and near-IR kinetic inductance detectors

Nicholas Zobrist, Grégoire Coiffard, Bruce Bumble +9 more

We report on the design and performance of microwave kinetic inductance detectors (MKIDs) sensitive to single photons in the optical to near-infrared range using hafnium as the sensor material. Our test device had a superconducting transition temperature of 395 mK and a room temperature normal state resistivity of 97 μΩ cm with RRR=1.6. Resonators on the device displayed internal quality factors of around 200 000. Similar to the analysis of MKIDs made from other highly resistive superconductors, we find that modeling the temperature response of the detector requires an extra broadening parameter in the superconducting density of states. Finally, we show that this material and design is compatible with a full-array fabrication process, which resulted in pixels with decay times of about 40 μs and resolving powers of ∼9 at 800 nm.

arXiv:1911.06434•Applied Physics Letters•Nov 18, 2019•30 citations

Characterization of sputtered hafnium thin films for high quality factor microwave kinetic inductance detectors

Grégoire Coiffard, M. Daal, Nicholas Zobrist +4 more

Abstract Hafnium is an elemental superconductor which crystallizes in a hexagonal close packed structure, has a transition temperature T C ≃ 400 mK, and has a high normal state resistivity around 90 µ ω cm. In Microwave Kinetic Inductance Detectors (MKIDs), these properties are advantageous since they allow for creating detectors sensitive to optical and near infra-red radiation. In this work, we study how sputter conditions and especially the power applied to the target during the deposition, affect the hafnium T C , resistivity, stress, texture and preferred crystal orientation. We find that the position of the target with respect to the substrate strongly affects the orientation of the crystallites in the films and the internal quality factor, Q i , of MKIDs fabricated from the films. In particular, we demonstrate that a DC magnetron sputter deposition at a normal angle of incidence, low pressure, and low plasma power promotes the growth of compressive (002)-oriented films and that such films can be used to make high quality factor MKIDs with Q i up to 600,000.

arXiv:2004.00736•Superconductor Science and Technology•Apr 27, 2020•21 citations

Ultra high quality factor resonators for kinetic inductance detectors

G. Hammer, S. Wünsch, K. Ilin +1 more

The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.

Journal of Physics Conference Series•Feb 1, 2008•12 citations

Strongly Nonlinear Superconducting Silicon Resonators

P. Bonnet, F. Chiodi, D. Flanigan +4 more

Superconducting boron-doped silicon is a promising material for integrated silicon quantum devices. In particular, its low electronic density and moderate disorder make it a suitable candidate for the fabrication of large inductances with low losses at microwave frequencies. We study experimentally the electrodynamics of superconducting silicon thin layers using coplanar waveguide resonators, focusing on the kinetic inductance, the internal losses, and the variation of these quantities with the resonator readout power. We report the observation in a doped semiconductor of microwave resonances with internal quality factors of a few thousand. As expected in the BCS framework, superconducting silicon presents a large sheet kinetic inductance in the 50--500-pH range, comparable to that of strongly disordered superconductors. The temperature dependence of the kinetic inductance is well described by the Mattis-Bardeen theory. However, we find an unexpectedly strong nonlinearity in the complex surface impedance that cannot be satisfactorily explained either by depairing or by quasiparticle heating.

arXiv:2101.11125•Physical Review Applied•Mar 23, 2022•13 citations

Kinetic inductance detectors for 200μm astronomy

Simon M. Doyle, Jack Alexander Naylon, James Cox +2 more

Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 14, 2006•4 citations

Magnetic field dependence of the internal quality factor and noise performance of lumped-element kinetic inductance detectors

D. Flanigan, B. R. Johnson, M. H. Abitbol +8 more

We present a technique for increasing the internal quality factor of kinetic inductance detectors (KIDs) by nulling ambient magnetic fields with a properly applied magnetic field. The KIDs used in this study are made from thin-film aluminum, they are mounted inside a light-tight package made from bulk aluminum, and they are operated near 150 mK. Since the thin-film aluminum has a slightly elevated critical temperature (Tc = 1.4 K), it therefore transitions before the package (Tc = 1.2 K), which also serves as a magnetic shield. On cooldown, ambient magnetic fields as small as approximately 30 µT can produce vortices in the thin-film aluminum as it transitions because the bulk aluminum package has not yet transitioned and therefore is not yet shielding. These vortices become trapped inside the aluminum package below 1.2 K and ultimately produce low internal quality factors in the thin-film superconducting resonators. We show that by controlling the strength of the magnetic field present when the thin film transitions, we can control the internal quality factor of the resonators. We also compare the noise performance with and without vortices present, and find no evidence for excess noise beyond the increase in amplifier noise, which is expected with increasing loss.

arXiv:1609.06352•Applied Physics Letters•Oct 3, 2016•21 citations
Kinetic inductance devices (KIDs) are superconducting resonators with high kinetic inductance sensitive to external energy perturbations. KIDs made with superconductors having TcT_cTc​ far below one Kelvin are of particular interest for sensing minuscule signals, such as light dark matter detection and millimeter wave telescopes for astronomy and cosmology. In this work, we report the promising performance of KIDs fabricated with Hafnium from heated sputter depositions. The KIDs have TcT_cTc​ lower than 249±\pm±2 mK, the internal quality factor (QiQ_iQi​) of the resonators exceeds 10510^5105 and the temperature dependence of the resonances can be described by the generalized Mattis-Bardeen model with a disorder parameter Γ=4×10−3Δ0Γ=4\times10^{-3}Δ_0Γ=4×10−3Δ0​. Post-fabrication annealing at temperatures above the deposition temperature can further reduce the TcT_cTc​ and ΓΓΓ without reducing QiQ_iQi​, leading to improvements in energy resolution.
We report on the design and performance of microwave kinetic inductance detectors (MKIDs) sensitive to single photons in the optical to near-infrared range using hafnium as the sensor material. Our test device had a superconducting transition temperature of 395 mK and a room temperature normal state resistivity of 97 μΩ cm with RRR=1.6. Resonators on the device displayed internal quality factors of around 200 000. Similar to the analysis of MKIDs made from other highly resistive superconductors, we find that modeling the temperature response of the detector requires an extra broadening parameter in the superconducting density of states. Finally, we show that this material and design is compatible with a full-array fabrication process, which resulted in pixels with decay times of about 40 μs and resolving powers of ∼9 at 800 nm.
Abstract Hafnium is an elemental superconductor which crystallizes in a hexagonal close packed structure, has a transition temperature T C ≃ 400 mK, and has a high normal state resistivity around 90 µ ω cm. In Microwave Kinetic Inductance Detectors (MKIDs), these properties are advantageous since they allow for creating detectors sensitive to optical and near infra-red radiation. In this work, we study how sputter conditions and especially the power applied to the target during the deposition, affect the hafnium T C , resistivity, stress, texture and preferred crystal orientation. We find that the position of the target with respect to the substrate strongly affects the orientation of the crystallites in the films and the internal quality factor, Q i , of MKIDs fabricated from the films. In particular, we demonstrate that a DC magnetron sputter deposition at a normal angle of incidence, low pressure, and low plasma power promotes the growth of compressive (002)-oriented films and that such films can be used to make high quality factor MKIDs with Q i up to 600,000.
The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.
Superconducting boron-doped silicon is a promising material for integrated silicon quantum devices. In particular, its low electronic density and moderate disorder make it a suitable candidate for the fabrication of large inductances with low losses at microwave frequencies. We study experimentally the electrodynamics of superconducting silicon thin layers using coplanar waveguide resonators, focusing on the kinetic inductance, the internal losses, and the variation of these quantities with the resonator readout power. We report the observation in a doped semiconductor of microwave resonances with internal quality factors of a few thousand. As expected in the BCS framework, superconducting silicon presents a large sheet kinetic inductance in the 50--500-pH range, comparable to that of strongly disordered superconductors. The temperature dependence of the kinetic inductance is well described by the Mattis-Bardeen theory. However, we find an unexpectedly strong nonlinearity in the complex surface impedance that cannot be satisfactorily explained either by depairing or by quasiparticle heating.
Kinetic inductance detectors (KIDs) provide an attractive solution to the production of large detector arrays for use in ground and space based 200μm astronomy. KIDs work by measuring the change in quasi-particle density upon photon absorption in a high Q superconducting resonator. A change in quasi-particle density is measured by a shift in phase of a microwave probe signal of frequency equal to that of the resonant frequency of the KID. Such detectors have a fundamental noise limit owing to the quasi-particle recombination rate, which, in a KID fabricated from a high quality Niobium film can give sensitivities of 10-18W√Hz at 1K. Constructing KIDs of varying resonant frequencies coupled to a single transmission line provides a multiplexed detector array with simple low temperature electronics. Here we discuss the theoretical requirements for both ground and space based 200μm cameras with various radiation coupling schemes for this wavelength range using distributed and lumped element high Q resonators.
We present a technique for increasing the internal quality factor of kinetic inductance detectors (KIDs) by nulling ambient magnetic fields with a properly applied magnetic field. The KIDs used in this study are made from thin-film aluminum, they are mounted inside a light-tight package made from bulk aluminum, and they are operated near 150 mK. Since the thin-film aluminum has a slightly elevated critical temperature (Tc = 1.4 K), it therefore transitions before the package (Tc = 1.2 K), which also serves as a magnetic shield. On cooldown, ambient magnetic fields as small as approximately 30 µT can produce vortices in the thin-film aluminum as it transitions because the bulk aluminum package has not yet transitioned and therefore is not yet shielding. These vortices become trapped inside the aluminum package below 1.2 K and ultimately produce low internal quality factors in the thin-film superconducting resonators. We show that by controlling the strength of the magnetic field present when the thin film transitions, we can control the internal quality factor of the resonators. We also compare the noise performance with and without vortices present, and find no evidence for excess noise beyond the increase in amplifier noise, which is expected with increasing loss.