The measurement of a superconducting qubit is implemented by coupling it to a resonator. The common choice is transverse coupling, which, in the dispersive approximation, introduces an interaction term that enables the measurement. This cross-Kerr term provides a qubit-state dependent dispersive shift in the resonator frequency with the device parameters chosen carefully to get sufficient signal while minimizing Purcell decay of the qubit. We introduce a two-mode circuit, nicknamed quantromon, with two orthogonal modes implementing a qubit and a resonator. Unlike before, where the coupling term emerges as a perturbative expansion, the quantromon has intrinsic cross-Kerr coupling by design. Our experiments implemented in a hybrid 2D–3D circuit QED architecture demonstrate some unique features of the quantromon like weak dependence of the dispersive shift on the qubit-resonator detuning and intrinsic Purcell protection. In a tunable qubit-frequency device, we show that the dispersive shift (2χ/2π) changes by only 0.8 MHz, while the qubit-resonator detuning (Δ/2π) is varied between 0.398 and 3.288 GHz. We also demonstrate Purcell protection in a second device where we tune the orthogonality between the two modes. Finally, we demonstrate a single-shot readout fidelity of 98.3%, which is comparable to the state-of-the-art measurements without the use of a parametric amplifier and suggests a potential simplification of the measurement circuitry for scaling up quantum processors.
The measurement of a superconducting qubit is implemented by coupling it to a resonator. The common choice is transverse coupling, which, in the dispersive approximation, introduces an interaction term that enables the measurement. This cross-Kerr term provides a qubit-state dependent dispersive shift in the resonator frequency with the device parameters chosen carefully to get sufficient signal while minimizing Purcell decay of the qubit. We introduce a two-mode circuit, nicknamed quantromon, with two orthogonal modes implementing a qubit and a resonator. Unlike before, where the coupling term emerges as a perturbative expansion, the quantromon has intrinsic cross-Kerr coupling by design. Our experiments implemented in a hybrid 2D–3D circuit QED architecture demonstrate some unique features of the quantromon like weak dependence of the dispersive shift on the qubit-resonator detuning and intrinsic Purcell protection. In a tunable qubit-frequency device, we show that the dispersive shift (2χ/2π) changes by only 0.8 MHz, while the qubit-resonator detuning (Δ/2π) is varied between 0.398 and 3.288 GHz. We also demonstrate Purcell protection in a second device where we tune the orthogonality between the two modes. Finally, we demonstrate a single-shot readout fidelity of 98.3%, which is comparable to the state-of-the-art measurements without the use of a parametric amplifier and suggests a potential simplification of the measurement circuitry for scaling up quantum processors.
Dispersive readout of superconducting qubits relies on a transverse capacitive coupling that hybridizes the qubit with the readout resonator, subjecting the qubit to Purcell decay and measurement-induced state transitions (MIST). Despite the widespread use of Purcell filters to suppress qubit decay and near-quantum-limited amplifiers, dispersive readout often lags behind single- and two-qubit gates in both speed and fidelity. Here, we experimentally demonstrate junction readout, a simple readout architecture that realizes a strong qubit-resonator cross-Kerr interaction without relying on a transverse coupling. This interaction is achieved by coupling a transmon qubit to its readout resonator through both a capacitance and a Josephson junction. By varying the qubit frequency, we show that this hybrid coupling provides intrinsic Purcell protection and enhanced resilience to MIST, enabling readout at high photon numbers. While junction readout is compatible with conventional linear measurement, in this work we exploit the nonlinear coupling to intentionally engineer a large Kerr nonlinearity in the resonator, enabling bifurcation-based readout. Using this approach, we achieve a 99.4 % assignment fidelity with a 68 ns integration time and a 98.4 % QND fidelity without an external Purcell filter or a near-quantum-limited amplifier. These results establish the junction readout architecture with bifurcation-based readout as a scalable and practical alternative to dispersive readout, enabling fast, high-fidelity qubit measurement with reduced hardware overhead.
We present a superconducting qubit for the circuit quantum electrodynamics architecture that has a tunable qubit-resonator coupling strength g. This coupling can be tuned from zero to values that are comparable with other superconducting qubits. At g = 0, the qubit is in a decoherence-free subspace with respect to spontaneous emission induced by the Purcell effect. Furthermore, we show that in this decoherence-free subspace, the state of the qubit can still be measured by either a dispersive shift on the resonance frequency of the resonator or by a cycling-type measurement.
The performance of a wide range of quantum computing algorithms and protocols depends critically on the fidelity and speed of the employed qubit readout. Examples include gate sequences benefiting from midcircuit real-time measurement-based feedback, such as qubit initialization, entanglement generation, teleportation, and, perhaps most importantly, quantum error correction. A prominent and widely used readout approach is based on the dispersive interaction of a superconducting qubit strongly coupled to a large-bandwidth readout resonator, frequently combined with a dedicated or shared Purcell filter protecting qubits from decay. By dynamically reducing the qubit-resonator detuning and thus increasing the dispersive shift, we demonstrate a beyond-state-of-the-art two-state-readout error of only 0.25% in 100-ns integration time. Maintaining low-readout-drive strength, we nearly quadruple the signal-to-noise ratio of the readout by doubling the readout-mode line width, which we quantify by considering the hybridization of the readout resonator and its dedicated Purcell filter. We find excellent agreement between our experimental data and our theoretical model. The presented results are expected to further boost the performance of new and existing algorithms and protocols critically depending on high-fidelity fast midcircuit measurements. Published by the American Physical Society 2024
Josephson junctions are a fundamental building block of superconducting quantum circuits. They provide the nonlinearity required to realize quantum bits and enable a wide range of nonlinear phenomena central to quantum technologies. This thesis explores two superconducting systems in which this nonlinearity plays a central role. In the first part, we investigate a superconducting resonator terminated by a superconducting quantum interference device (SQUID), an arrangement of two Josephson junctions connected in parallel. The SQUID provides a tunable Kerr nonlinearity and allows the resonator to be driven parametrically. Under the combined action of the parametric drive, Kerr nonlinearity, and dissipation to the environment, the state of the resonator can undergo abrupt changes as the pump frequency or amplitude is varied. We interpret these changes within the framework of dissipative phase transitions (DPTs). By implementing a finite-component thermodynamic limit, we experimentally and theoretically investigate both first- and second-order DPTs in this system. We characterize their steady-state and dynamical signatures, including squeezing below vacuum, phase coexistence, hysteresis, spontaneous symmetry breaking, and critical slowing down. Finally, we exploit the enhanced susceptibility near the second-order critical point to implement a frequency-estimation protocol. We show that the estimation precision scales quadratically with the effective system size, demonstrating that finite-component DPTs can provide a quantum advantage in a sensing protocol. In the second part, we investigate a novel architecture for the readout of superconducting qubits. Conventional dispersive readout relies on a transverse interaction between a transmon and a resonator, which can lead to Purcell decay and measurement-induced state transitions, ultimately limiting the readout fidelity. To overcome these limitations, we implement a nonlinear coupling by galvanically connecting the transmon and resonator through a Josephson junction. This interaction provides a strong cross-Kerr coupling for clear state discrimination, but also introduces a detrimental transverse interaction. We experimentally show that the exchange part of the transverse interaction can be suppressed by adding a capacitor in parallel with the coupling junction while preserving the strong cross-Kerr coupling. In addition, we show that the same circuit acts as an intrinsic Purcell filter, protecting the qubit against Purcell decay. The coupling junction also induces a Kerr nonlinearity in the resonator, which we exploit to implement a bifurcation readout with a 99.4 % fidelity in a 68 ns integration time. This performance is achieved without a dedicated Purcell filter or a near-quantum-limited amplifier. Overall, this thesis demonstrates the engineering of nonlinear superconducting circuits to investigate dissipative phase transitions, exploit criticality for enhanced quantum sensing, and develop a novel qubit readout architecture enabling fast, high-fidelity measurement.
This dissertation examines the design, fabrication, and characterization of a superconducting lumped-element tunable LC resonator that is used to vary the coupling between two superconducting qubits. Some level of qubit-qubit coupling is needed to perform gating operations. However, with fixed coupling, single qubit operations become considerably more difficult due to dispersive shifts in their energy levels transitions that depend on the state of the other qubit. Ideally, one wants a system in which the qubit-qubit coupling can be turned off to allow for single qubit operations, and then turned back on to allow for multi-qubit gate operations. I present results on a device that has two fixed-frequency transmon qubits capacitively coupled to a tunable thin-film LC resonator. The resonator can be tuned in situ over a range of 4.14 GHz to 4.94 GHz by applying an external magnetic flux to two single-Josephson junction loops, which are incorporated into the resonator’s inductance. The qubits have 0-to-1 transition frequencies of 5.10 GHz and 4.74 GHz. To isolate the system and provide a means for reading out the state of the qubit readout, the device was mounted in a 3D Al microwave cavity with a TE101 mode resonance frequency of about 6.1 GHz. The flux-dependent transition frequencies of the system were measured and fit to results from a coupled Hamiltonian model. With the LC resonator tuned to its minimum resonance frequency, I observed a qubit-qubit dispersive shift of 2χ_qq≈ 0.1 MHz, which was less than the linewidth of the qubit transitions. This dispersive shift was sufficiently small to consider the coupling “off”, allowing single qubit operations. The qubit-qubit dispersive shift varied with the applied flux up to a maximum dispersive shift of 2χ_qq≈ 6 MHz. As a proof-of-principle, I present preliminary results on performing a CNOT gate operation on the qubits when the coupling was “on” with 2χ_qq≈ 4 MHz. This dissertation also includes observations of the temperature dependence of the relaxation time T1 of three Al/AlOx/Al transmons. We found that, in some cases, T1 increased by almost a factor of two as the temperature increased from 30 mK to 100 mK. We found that this anomalous behavior was consistent with loss due to non-equilibrium quasiparticles in a transmon where one electrode in the tunnel junction had a smaller volume and slightly smaller superconducting energy gap than the other electrode. At sufficiently low temperatures, non-equilibrium quasiparticles accumulate in the electrode with a smaller gap, leading to an increased density of quasiparticles at the junction and a corresponding decrease in the relaxation time. I present a model of this effect, use the model to extract the density of non-equilibrium quasiparticles in the device, and find the values of the two superconducting energy gaps.
Efficient qubit reset and leakage reduction are essential for scalable superconducting quantum computing, particularly in the context of quantum error correction. However, such operations often require additional on-chip components. Here, we propose and experimentally demonstrate a hardware-efficient approach to qubit reset and readout using a multi-mode Purcell filter in a superconducting quantum circuit. We exploit the inherent multi-mode structure of a coplanar waveguide resonator, using its fundamental and second-order modes for qubit reset and readout, respectively, thereby avoiding additional components. Implemented in a flip-chip architecture, our device achieves unconditional reset with residual excitation below 1\% in 220 ns, and a leakage reduction unit that selectively resets the second excited state within 62 ns with a residual ∣f⟩ population of 6.1\%, accounting for the readout error. Despite the qubits being directly coupled to the filter in our configuration, the measured relaxation times are not degraded owing to intrinsic Purcell protection provided by an auxiliary mode. To our knowledge, this is the first experimental trial that exploits different-order modes of a microwave resonator for distinct qubit operations, representing a new direction toward scalable, hardware-efficient quantum processor design.