Performance of superconducting resonators suspended on SiN membranes
Trevor Chistolini, Kyunghoon Lee, Archan Banerjee, Mohammed Alghadeer, Christian Jünger, M. Virginia P. Altoé, Chengyu Song, Su-Di Chen, Feng Wang, David Santiago, Irfan A. Siddiqi
Suspending devices on thin SiN membranes can limit their interaction with the bulk substrate and reduce parasitic capacitance to ground. While suspending devices on membranes are used in many fields including radiation detection using superconducting circuits, there has been less investigation into maximum membrane aspect ratios and achievable suspended device quality, metrics important to establish the applicable scope of the technique. Here, we investigate these metrics by fabricating superconducting coplanar waveguide resonators entirely atop thin (∼110 nm) SiN membranes, where the membrane's shortest length to thickness yields an aspect ratio of approximately 7.4×103. We compare these membrane resonators to on-substrate resonators on the same chip, finding similar internal quality factors ∼105 at single photon levels. Furthermore, we confirm that these membranes do not adversely affect resonator thermalization and conduct further materials characterization. By achieving high quality superconducting circuit devices fully suspended on thin SiN membranes, our results help expand the technique's scope to potential uses including incorporating higher aspect ratio membranes for device suspension and creating larger footprint, high impedance, and high quality devices.
Suspending devices on thin SiN membranes can limit their interaction with the bulk substrate and reduce parasitic capacitance to ground. While suspending devices on membranes are used in many fields including radiation detection using superconducting circuits, there has been less investigation into maximum membrane aspect ratios and achievable suspended device quality, metrics important to establish the applicable scope of the technique. Here, we investigate these metrics by fabricating superconducting coplanar waveguide resonators entirely atop thin (∼110 nm) SiN membranes, where the membrane's shortest length to thickness yields an aspect ratio of approximately 7.4×103. We compare these membrane resonators to on-substrate resonators on the same chip, finding similar internal quality factors ∼105 at single photon levels. Furthermore, we confirm that these membranes do not adversely affect resonator thermalization and conduct further materials characterization. By achieving high quality superconducting circuit devices fully suspended on thin SiN membranes, our results help expand the technique's scope to potential uses including incorporating higher aspect ratio membranes for device suspension and creating larger footprint, high impedance, and high quality devices.
Superinductors have become a crucial component in the superconducting circuit toolbox, playing a key role in the development of more robust qubits. Enhancing the performance of these devices can be achieved by suspending the superinductors from the substrate, thereby reducing stray capacitance. Here, we present a fabrication framework for constructing superconducting circuits with suspended superinductors in planar architectures. To validate the effectiveness of this process, we systematically characterize both resonators and qubits with suspended arrays of Josephson junctions, ultimately confirming the high quality of the superinductive elements. In addition, this process is broadly compatible with other types of superinductors and circuit designs. Our results not only pave the way for scalable superconducting architectures utilizing superinductors but also provide the primitive for future investigation of loss mechanisms associated with the device substrate.
In this master's thesis, I present the design, fabrication, and characterisation of superconducting microwave resonators. These resonators are quarter-wavelength coplanar waveguide resonators, operating at resonance frequencies between 4 GHz and 8 GHz. This kind of resonator is a key component in several applications, ranging from quantum computation devices to parametric amplifiers. Minimising the losses (achieving high internal quality factors) in these resonators is important to maximise performance of the applications they are used for. During the thesis work, we have studied several possible changes to improve the resonator quality.\n\nFabrication of the resonators was done in the Nanofabrication Laboratory at Chalmers University of Technology, and consist of the following steps: cleaning a sapphire or silicon wafer, depositing a layer of superconducting niobium, photolithography, and etching the waveguide. We then measured the resonators in a cryogen-free dilution refrigerator, at a temperature of 10 mK. The measurements consisted of a power sweep, in order to quantify the quality factor at high and low excitation powers. As an example, the first resonator we fabricated had a quality factor of 4.3 x 10^4 at high power (about 10^5 photons in the resonator), and quality factor of 3.7 x 10^4 at the single-photon level.\n\nWe then investigated different loss mechanisms that we expect to negatively affect the quality factor, and how to reduce this loss. Firstly, to reduce radiation losses and magnetic vortex losses, we reduced the lateral dimensions of the resonator. Secondly, as two-level system (TLS) losses are believed to mainly reside at the surfaces of the materials and interfaces between them, we etched into the substrate to selectively move a part of the TLS away from the resonator. We also studied the effect of the meandering of the resonator on the quality factor, as well as using two different etching gasses.\n\nBy gathering all this data, we were then able to compare the different combinations to see the effect of the changing parameters. In conclusion, the reduced lateral dimensions and the removal of part of the substrate indeed reduce the losses, as expected from the theory. We also found interesting behaviour with regards to the meandering, namely that having a meandered structure negatively affects the quality factor.\n\nCombining all results, we can give a guideline for the fabrication of resonators in the future, which gave us a quality factor up to 4.9 x 10^5 at high excitation power, and 3.0 x 10^5 at the single photon level.
Superconducting coplanar waveguide (CPW) microwave resonators are crucial elements in Photon detectors, Quantum-limited parametric amplifiers, Narrow-band filters, Read-out, interconnect in quantum processors and Hybrid devices, connecting solid-state spins with superconducting circuits [1-3]. In the quantum regime, the dominant loss mechanism for high-Q superconducting resonators can be attributed to parasitic two-level systems (TLSs) in the dielectrics. Interface TLSs are common by products of the fabrication process, often introduced by impurities associated with Si surfaces [3]. To reduce intrinsic losses, we employ isotropic deep reactive-ion etching (DRIE) of Si substrate to create suspended NbN superconducting resonators (SSR).In this study, thin films of niobium (Nb) and niobium nitride (NbN) are deposited on Si substrate by a DC magnetron sputtering system. The influence of the N2/Ar gas ratio, the deposition current, the substrate bias potential on the superconducting critical temperature of the films are investigated. Plasma etching of Nb and NbN in a SF6 and Cl2-BCl3 gas plasma is studied using an inductively coupled plasma (icp) reactor. Parametric studies on the effects of total gas flow rate and chamber pressure on the edge angles and etch rates are reported. Finally, the suspended NbN superconducting resonator is fabricated and will be tested. This could be applied to the fabrication of superconducting qubits in integrated circuits, offering a path towards longer qubit coherence times.Reference:[1] Landig et al. Coherent spin–photon coupling using a resonant exchange qubit. Nature 560, 179–184 (2018)[2] Tosi et al. Silicon quantum processor with robust long-distance qubit couplings. Nat Commun 8, 450 (2017)[3] Bruno et al. Reducing intrinsic loss in superconducting resonators by surface treatment and deep etching of silicon substrates, Appl. Phys. Lett. 106, 182601 (2015)[4] Kennedy et al. Tunable Nb Superconducting Resonator Based on a Constriction Nano-SQUID Fabricated with a Ne Focused Ion Beam, Phys. Rev. Applied 11, 014006 (2019).
We report on the design, fabrication, and characterization of superconducting coplanar waveguide resonators with nanoscopic constrictions. By reducing the size of the center line down to 50 nm, the radio frequency currents are concentrated and the magnetic field in its vicinity is increased. The device characteristics are only slightly modified by the constrictions, with changes in resonance frequency lower than 1% and internal quality factors of the same order of magnitude as the original ones. These devices could enable the achievement of higher couplings to small magnetic samples or even to single molecular spins and have applications in circuit quantum electrodynamics, quantum computing, and electron paramagnetic resonance.
Abstract The performance of state-of-the-art superconducting quantum devices is currently limited by microwave dielectric loss at different interfaces. α -tantalum is a superconductor that has proven effective in reducing dielectric loss and improving device performance due to its thin low-loss oxide. Here, we demonstrate the fabrication of high-quality factor α -tantalum coplanar-waveguide resonators directly on pristine 300 mm silicon wafers over a variety of metal deposition conditions and perform a comprehensive material and electrical characterization study. Additionally, we apply a surface treatment based on hydrofluoric acid that allows us to modify different resonators surfaces, leading to a reduction in two-level system loss in the devices by a factor of three. This loss reduction can be entirely attributed to the removal of surface oxides. Our study indicates that large scale manufacturing of low-loss superconducting circuits should indeed be feasible and suggests a viable avenue to materials-driven advancements in superconducting circuit performance.
Niobium and aluminum have been widely used to realize superconducting resonators and qubits. However, the native oxide at the metal air interface limits the devices results. This layer is highly disordered, and it induces losses limiting the performances of the resonators or qubits. Recently, tantalum led to great improvement in qubit relaxation time. This improvement has been attributed to a thinner and less disordered oxide layer compared to Nb and Al. This study is aimed to limit the formation of the oxide layer, by the introduction of novel superconducting materials such as rhenium or by encapsulating the Nb surface with other superconducting materials such as Ta, Al, Re or other non-superconducting materials such as Au. To better understand the results, we are realizing these studies on coplanar waveguide resonators where the relation between surface losses and quality factor is clear. We are also analyzing different fabrication techniques to completely characterize our devices, linking material properties to the performances. In this work we are also varying the participation ratio of the devices in order to extract with higher fidelity and precision the losses introduced by the involved interfaces.