Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2310.07195 · Quantum Science and Technology

Bilayer ion trap design for 2D arrays

Gavin Nop, Jonathan D. H. Smith, Daniel Stick, Durga Paudyal

Published Apr 16, 2024• 2 citations
arXivHTMLPDF

Abstract

Abstract Junctions are fundamental elements that support qubit locomotion in two-dimensional ion trap arrays and enhance connectivity in emerging trapped-ion quantum computers. In surface ion traps they have typically been implemented by shaping radio frequency (RF) electrodes in a single plane to minimize the disturbance to the pseudopotential. However, this method introduces issues related to RF lead routing that can increase power dissipation and the likelihood of voltage breakdown. Here, we propose and simulate a novel two-layer junction design incorporating two perpendicularly rotoreflected (rotated, then reflected) linear ion traps. The traps are vertically separated, and create a trapping potential between their respective planes. The orthogonal orientation of the RF electrodes of each trap relative to the other provides perpendicular axes of confinement that can be used to realize transport in two dimensions. While this design introduces manufacturing and operating challenges, as now two separate structures have to be precisely positioned relative to each other in the vertical direction and optical access from the top is obscured, it obviates the need to route RF leads below the top surface of the trap and eliminates the pseudopotential bumps that occur in typical junctions. In this paper the stability of idealized ion transfer in the new configuration is demonstrated, both by solving the Mathieu equation analytically to identify the stable regions and by numerically modeling ion dynamics. Our novel junction layout has the potential to enhance the flexibility of microfabricated ion trap control to enable large-scale trapped-ion quantum computing.

DOI
10.1088/2058-9565/ad3f43

Related papers

Multi-junction surface ion trap for quantum computing

Jonathan David Sterk, Matthew G. Blain, Delaney, M. +11 more

Surface ion traps with two-dimensional layouts of trapping regions are natural architectures for storing large numbers of ions and supporting the connectivity needed to implement quantum algorithms. Many of the components and operations needed to fully exploit this architecture have already been demonstrated, including operation at cryogenic temperatures with low heating, low excitation transport, and ion control and detection with integrated photonics. Here we demonstrate a trap that addresses the scaling challenge of increasing power dissipation as the RF electrode increases in size. By raising the RF electrode and removing most of the insulating dielectric layer below it we reduce both ohmic and dielectric power dissipation. We also measure heating rates across a range of motional frequencies and for different voltage sources in a trap with a raised RF electrode but solid dielectric.

arXiv:2403.00208•Mar 1, 2024•1 citation

Feasibility Study of 3D-Printed Micro Junction Array for Ion Trap Quantum Processor

Kento Taniguchi, Ke Sun, Shuqi Xu +6 more

We introduce an ion trap platform based on a 3D-printed micro-junction array, designed to implement quantum charge-coupled device (QCCD) architectures for large-scale quantum information processing (QIP). The integration of three-dimensionally structured micro Radio-Frequency (RF) electrodes above a surface-electrode trap enables flexible control of electric field profiles across both linear and junction regions. Through simulations, we demonstrate that the linear region exhibits deeper and more harmonic ion confinement with reduced RF drive power compared to conventional planar traps. Crucially, we identify a junction geometry that maintains uniform ion confinement during transport while substantially reducing the pseudopotential barrier. This reduction facilitates low-heating, high-fidelity transport of single- and multi-species ion crystals. Our results establish a viable route toward fault-tolerant quantum computing by enabling modular and scalable QCCD systems based on the state-of-the-art 3D-printing technologies.

arXiv:2509.17275•Sep 21, 2025•0 citations

Ytterbium ion trapping and microfabrication of ion trap arrays

R. C. Sterling

Over the past 15 years ion traps have demonstrated all the building blocks required of a quantum computer. Despite this success, trapping ions remains a challenging task, with the requirement for extensive laser systems and vacuum systems to perform operations on only a handful of qubits. To scale these proof of principle experiments into something that can outperform a classical computer requires an advancement in the trap technologies that will allow multiple trapping zones, junctions and utilize scalable fabrication technologies. I will discuss the construction of an ion trapping experiment, focussing on my work towards the laser stabilization and ion trap design but also covering the experimental setup as a whole. The vacuum system that I designed allows the mounting and testing of a variety of ion trap chips, with versatile optical access and a fast turn around time. I will also present the design and fabrication of a microfabricated Y junction and a 2- dimensional ion trap lattice. I achieve a suppression of barrier height and small variation of secular frequency through the Y junction, aiding to the junctions applicability to adiabatic shuttling operations. I also report the design and fabrication of a 2-D ion trap lattice. Such structures have been proposed as a means to implement quantum simulators and to my knowledge is the first microfabricated lattice trap. Electrical testing of the trap structures was undertaken to investigate the breakdown voltage of microfabricated structures with both static and radio frequency voltages. The results from these tests negate the concern over reduced rf voltage breakdown and in fact demonstrates breakdown voltages significantly above that typically required for ion trapping. This may allow ion traps to be designed to operate with higher voltages and greater ion-electrode separations, reducing anomalous heating. Lastly I present my work towards the implementation of magnetic fields gradients and microwaves on chip. This may allow coupling of the ions internal state to its motion using microwaves, thus reducing the requirements for the use of laser systems.

•Jun 11, 2012•2 citations

Reliable transport through a microfabricated X -junction surface-electrode ion trap

Kenneth Wright, Jason Amini, Daniel L. Faircloth +9 more

We report the design, fabrication and characterization of a microfabricated surface-electrode ion trap that supports controlled transport through the two-dimensional intersection of linear trapping zones arranged in a 90° cross. The trap is fabricated with very large scalable integration techniques which are compatible with scaling to a large quantum information processor. The shape of the radio-frequency electrodes is optimized with a genetic algorithm to reduce axial pseudopotential barriers and minimize ion heating during transport. Seventy-eight independent dc control electrodes enable fine control of the trapping potentials. We demonstrate reliable ion transport between junction legs and determine the rate of ion loss due to transport. Doppler-cooled ions survive more than 10 5 round-trip transits between junction legs without loss and more than 65 consecutive round trips without laser cooling.

arXiv:1210.3655•New Journal of Physics•Mar 4, 2013•87 citations

Optimization and implementation of a surface-electrode ion trap junction

Chi Zhang, Karan K. Mehta, Jonathan Home

Abstract We describe the design of a surface-electrode ion trap junction, which is a key element for large-scale ion trap arrays. A bi-objective optimization method is used for designing the electrodes, which maintains the total pseudo-potential curvature while minimizing the axial pseudo-potential gradient along the ion transport path. To facilitate the laser beam delivery for parallel operations in multiple trap zones, we implemented integrated optics on each arm of this X-junction trap. The layout of the trap chip for commercial foundry fabrication is presented. This work suggests routes to improving ion trap junction performance in scalable implementations. Together with integrated optical addressing, this contributes to modular trapped-ion quantum computing in interconnected two-dimensional arrays.

arXiv:2201.12579•New Journal of Physics•Jul 1, 2022•10 citations

The development of microfabricated ion traps towards quantum information and simulation

Marcus Hughes

Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.

•Jun 16, 2013•0 citations
Abstract Junctions are fundamental elements that support qubit locomotion in two-dimensional ion trap arrays and enhance connectivity in emerging trapped-ion quantum computers. In surface ion traps they have typically been implemented by shaping radio frequency (RF) electrodes in a single plane to minimize the disturbance to the pseudopotential. However, this method introduces issues related to RF lead routing that can increase power dissipation and the likelihood of voltage breakdown. Here, we propose and simulate a novel two-layer junction design incorporating two perpendicularly rotoreflected (rotated, then reflected) linear ion traps. The traps are vertically separated, and create a trapping potential between their respective planes. The orthogonal orientation of the RF electrodes of each trap relative to the other provides perpendicular axes of confinement that can be used to realize transport in two dimensions. While this design introduces manufacturing and operating challenges, as now two separate structures have to be precisely positioned relative to each other in the vertical direction and optical access from the top is obscured, it obviates the need to route RF leads below the top surface of the trap and eliminates the pseudopotential bumps that occur in typical junctions. In this paper the stability of idealized ion transfer in the new configuration is demonstrated, both by solving the Mathieu equation analytically to identify the stable regions and by numerically modeling ion dynamics. Our novel junction layout has the potential to enhance the flexibility of microfabricated ion trap control to enable large-scale trapped-ion quantum computing.
Surface ion traps with two-dimensional layouts of trapping regions are natural architectures for storing large numbers of ions and supporting the connectivity needed to implement quantum algorithms. Many of the components and operations needed to fully exploit this architecture have already been demonstrated, including operation at cryogenic temperatures with low heating, low excitation transport, and ion control and detection with integrated photonics. Here we demonstrate a trap that addresses the scaling challenge of increasing power dissipation as the RF electrode increases in size. By raising the RF electrode and removing most of the insulating dielectric layer below it we reduce both ohmic and dielectric power dissipation. We also measure heating rates across a range of motional frequencies and for different voltage sources in a trap with a raised RF electrode but solid dielectric.
We introduce an ion trap platform based on a 3D-printed micro-junction array, designed to implement quantum charge-coupled device (QCCD) architectures for large-scale quantum information processing (QIP). The integration of three-dimensionally structured micro Radio-Frequency (RF) electrodes above a surface-electrode trap enables flexible control of electric field profiles across both linear and junction regions. Through simulations, we demonstrate that the linear region exhibits deeper and more harmonic ion confinement with reduced RF drive power compared to conventional planar traps. Crucially, we identify a junction geometry that maintains uniform ion confinement during transport while substantially reducing the pseudopotential barrier. This reduction facilitates low-heating, high-fidelity transport of single- and multi-species ion crystals. Our results establish a viable route toward fault-tolerant quantum computing by enabling modular and scalable QCCD systems based on the state-of-the-art 3D-printing technologies.
Over the past 15 years ion traps have demonstrated all the building blocks required of a quantum computer. Despite this success, trapping ions remains a challenging task, with the requirement for extensive laser systems and vacuum systems to perform operations on only a handful of qubits. To scale these proof of principle experiments into something that can outperform a classical computer requires an advancement in the trap technologies that will allow multiple trapping zones, junctions and utilize scalable fabrication technologies. I will discuss the construction of an ion trapping experiment, focussing on my work towards the laser stabilization and ion trap design but also covering the experimental setup as a whole. The vacuum system that I designed allows the mounting and testing of a variety of ion trap chips, with versatile optical access and a fast turn around time. I will also present the design and fabrication of a microfabricated Y junction and a 2- dimensional ion trap lattice. I achieve a suppression of barrier height and small variation of secular frequency through the Y junction, aiding to the junctions applicability to adiabatic shuttling operations. I also report the design and fabrication of a 2-D ion trap lattice. Such structures have been proposed as a means to implement quantum simulators and to my knowledge is the first microfabricated lattice trap. Electrical testing of the trap structures was undertaken to investigate the breakdown voltage of microfabricated structures with both static and radio frequency voltages. The results from these tests negate the concern over reduced rf voltage breakdown and in fact demonstrates breakdown voltages significantly above that typically required for ion trapping. This may allow ion traps to be designed to operate with higher voltages and greater ion-electrode separations, reducing anomalous heating. Lastly I present my work towards the implementation of magnetic fields gradients and microwaves on chip. This may allow coupling of the ions internal state to its motion using microwaves, thus reducing the requirements for the use of laser systems.
We report the design, fabrication and characterization of a microfabricated surface-electrode ion trap that supports controlled transport through the two-dimensional intersection of linear trapping zones arranged in a 90° cross. The trap is fabricated with very large scalable integration techniques which are compatible with scaling to a large quantum information processor. The shape of the radio-frequency electrodes is optimized with a genetic algorithm to reduce axial pseudopotential barriers and minimize ion heating during transport. Seventy-eight independent dc control electrodes enable fine control of the trapping potentials. We demonstrate reliable ion transport between junction legs and determine the rate of ion loss due to transport. Doppler-cooled ions survive more than 10 5 round-trip transits between junction legs without loss and more than 65 consecutive round trips without laser cooling.
Abstract We describe the design of a surface-electrode ion trap junction, which is a key element for large-scale ion trap arrays. A bi-objective optimization method is used for designing the electrodes, which maintains the total pseudo-potential curvature while minimizing the axial pseudo-potential gradient along the ion transport path. To facilitate the laser beam delivery for parallel operations in multiple trap zones, we implemented integrated optics on each arm of this X-junction trap. The layout of the trap chip for commercial foundry fabrication is presented. This work suggests routes to improving ion trap junction performance in scalable implementations. Together with integrated optical addressing, this contributes to modular trapped-ion quantum computing in interconnected two-dimensional arrays.
Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.