We experimentally demonstrate a virtual two-qubit gate and characterize it using quantum process tomography (QPT). The virtual two-qubit gate decomposes an actual two-qubit gate into single-qubit unitary gates and projection gates in quantum circuits for expectation-value estimation. We implement projection gates via midcircuit measurements. The deterministic sampling scheme reduces the number of experimental circuit evaluations required for decomposing a virtual two-qubit gate. We also apply quantum error mitigation to suppress the effect of measurement errors and improve the average gate fidelity of a virtual controlled- Z (CZ) gate to fav=0.9938±0.0002 . Our results highlight a practical approach to implement virtual two-qubit gates with high fidelities, which are useful for simulating quantum circuits using fewer qubits and implementing two-qubit gates on a distant pair of qubits. Published by the American Physical Society 2024
We experimentally demonstrate a virtual two-qubit gate and characterize it using quantum process tomography (QPT). The virtual two-qubit gate decomposes an actual two-qubit gate into single-qubit unitary gates and projection gates in quantum circuits for expectation-value estimation. We implement projection gates via midcircuit measurements. The deterministic sampling scheme reduces the number of experimental circuit evaluations required for decomposing a virtual two-qubit gate. We also apply quantum error mitigation to suppress the effect of measurement errors and improve the average gate fidelity of a virtual controlled- Z (CZ) gate to fav=0.9938±0.0002 . Our results highlight a practical approach to implement virtual two-qubit gates with high fidelities, which are useful for simulating quantum circuits using fewer qubits and implementing two-qubit gates on a distant pair of qubits. Published by the American Physical Society 2024
Abstract We show a certain kind of non-local operations can be simulated by sampling a set of local operations with a quasi-probability distribution when the task of a quantum circuit is to evaluate an expectation value of observables. Utilizing the result, we describe a strategy to decompose a two-qubit gate to a sequence of single-qubit operations. Required operations are projective measurement of a qubit in Pauli basis, and π/2 rotation around x, y, and z axes. The required number of sampling to get an expectation value of a target observable within an error of ϵ is roughly O(9 k /ϵ 2), where k is the number of ‘cuts’ performed. The proposed technique enables to perform ‘virtual’ gates between a distant pair of qubits, where there is no direct interaction and thus a number of swap gates are inevitable otherwise. It can also be utilized to improve the simulation of a large quantum computer with a small-sized quantum device, which is an idea put forward by Peng et al (2019 arXiv: 1904.00102 ). This work can enhance the connectivity of qubits on near-term, noisy quantum computers.
High-quality two-qubit gate operations are crucial for scalable quantum information processing. Often, the gate fidelity is compromised when the system becomes more integrated. Therefore, a low-error-rate, easy-to-scale two-qubit gate scheme is highly desirable. Here, we experimentally demonstrate a new two-qubit gate scheme that exploits fixed-frequency qubits and a tunable coupler in a superconducting quantum circuit. The scheme requires less control lines, reduces cross talk effect, and simplifies calibration procedures, yet produces a controlled-Z gate in 30 ns with a high fidelity of 99.5%, derived from the interleaved randomized benchmarking method. Error analysis shows that gate errors are mostly coherence limited. Our demonstration paves the way for large-scale implementation of high-fidelity quantum operations.
As quantum devices make steady progress towards intermediate scale and fault-tolerant quantum computing, it is essential to develop rigorous and efficient measurement protocols that account for known sources of noise. Most existing quantum characterization protocols such as gate-set tomography and randomized benchmarking assume the noise acting on the qubits is Markovian. However, this assumption is often not valid, as for the case of 1/f charge noise or hyperfine nuclear spin noise. Here, we present a general framework for quantum process tomography (QPT) in the presence of time-correlated noise. We further introduce fidelity benchmarks that quantify the relative strength of different sources of Markovian and non-Markovian noise. As an application of our method, we perform a comparative theoretical and experimental analysis of silicon spin qubits. We first develop a detailed noise model that accounts for the dominant sources of noise and validate the model against experimental data. Applying our framework for time-correlated QPT, we find that the number of independent parameters needed to characterize one- and two-qubit gates can be compressed by 10× and 100× , respectively, when compared to the fully generic case. These compressions reduce the amount of tomographic measurements needed in experiment, while also significantly speeding up numerical simulations of noisy quantum circuit dynamics compared to time-dependent Hamiltonian simulation. Using this compressed noise model, we find good agreement between our theoretically predicted process fidelities and two-qubit interleaved randomized benchmarking fidelities of 99.8% measured in recent experiments on silicon spin qubits. More broadly, our formalism can be directly extended to develop efficient and scalable tuning protocols for high-fidelity control of large arrays of quantum devices with non-Markovian noise. Published by the American Physical Society 2024
In circuit-based quantum computing the available gate set typically consists of single-qubit gates acting on each individual qubit and at least one entangling gate between pairs of qubits.In certain physical architectures, however, some qubits may be "hidden" and lacking direct addressability through dedicated control and readout lines, for instance, because of limited on-chip routing capabilities, or because the number of control lines becomes a limiting factor for many-qubit systems.In this case, no single-qubit operations can be applied to the hidden qubits and their state cannot be measured directly.Instead, they may be controlled and read out only via single-qubit operations on connected "control" qubits and a suitable set of two-qubit gates.We first discuss the impact of such restricted control capabilities on the performance of specific qubit coupling networks.We then experimentally demonstrate full control and measurement capabilities in a superconducting two-qubit device with local single-qubit control and iSWAP and controlledphase two-qubit interactions enabled by a tunable coupler.We further introduce an iterative tune-up process required to completely characterize the gate set used for quantum process tomography and evaluate the resulting gate fidelities.
The Berkeley gate is a high-performance, two-qubit entangling operation with particular potential for quantum error correction and fault-tolerant protocols. However, harnessing this potential on current noisy intermediate-scale quantum (NISQ) processors, requires efficient compilation and robust performance under realistic noise conditions. In this work, we demonstrate a hardware-efficient implementation of the Berkeley gate on a superconducting quantum processor. Using quantum process tomography (QPT), we experimentally characterize its performance and benchmark it against a noiseless quantum simulator to evaluate its practical reliability in the NISQ era. Experimental measurements confirm the gate's correct logical action, producing the target partially entangled state with a subspace confinement probability of [Formula: see text] on real quantum hardware compared to 100% in quantum simulation. Results from QPT experiments show a simulated process fidelity of [Formula: see text], while the experimental process fidelity on hardware is [Formula: see text]. The observed discrepancy is analyzed in the context of device-specific noise sources, including qubit relaxation, dephasing, and state preparation and measurement (SPAM) errors. Our work provides a concrete fidelity benchmark for the Berkeley gate on superconducting hardware and quantify the impact of realistic noise on a non-trivial two-qubit operation, supporting its use in near-term algorithmic and error-correction applications.
While the common practice of decomposing general quantum algorithms into a collection of single- and two-qubit gates is conceptually simple, in many cases it is possible to have more efficient solutions where quantum gates engaging multiple qubits are used. In the noisy intermediate-scale quantum (NISQ) era where a universal error correction is still unavailable, this strategy is particularly appealing since it can significantly reduce the computational resources required for executing quantum algorithms. In this work, we experimentally investigate a three-qubit Controlled-CPHASE-SWAP (CCZS) gate on superconducting quantum circuits. By exploiting the higher energy levels of superconducting qubits, we are able to realize a Fredkin-like CCZS gate with a duration of 40 ns, which is comparable to typical single- and two-qubit gates realized on the same platform. By performing quantum process tomography for the two target qubits, we obtain a process fidelity of 86.0% and 81.1% for the control qubit being prepared in ∣0〉 and ∣1〉, respectively. We also show that our scheme can be readily extended to realize a general CCZS gate with an arbitrary swap angle. The results reported here provide valuable additions to the toolbox for achieving large-scale hardware-efficient quantum circuits.