Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2103.06803

Spurious Antenna Modes of the Transmon Qubit

O. Rafferty, S. Patel, C. H. Liu, Abdullah, S., Christopher D. Wilen, D. C. Harrison, R. McDermott

Published Mar 11, 2021• 25 citations
arXivHTMLPDF

Abstract

Superconducting qubits are resonant absorbers of pair-breaking radiation. The metal pads that form the qubit capacitance support standing wave modes at frequencies of order 100~GHz; these modes are strongly coupled to free-space impedance through their electric dipole moment. While the antenna mode of the 3D transmon qubit is easily seen to be a resonant dipole, other 2D qubit types can be understood as the aperture duals of wire loop antennas or folded dipoles. For typical Josephson junction parameters, the junction provides a reasonable conjugate match to the fundamental antenna mode. We calculate the contribution to quasiparticle poisoning from resonant absorption of blackbody radiation. We extend our analysis to dissipation at the qubit frequency, where radiative losses provide an ultimate limit to qubit energy relaxation time. A clear understanding of the spurious antenna modes of qubits will allow designs that are insensitive to pair-breaking radiation and that display reduced radiative losses at the qubit frequency.

DOI
10.48550/arxiv.2103.06803

Related papers

Quasiparticle Poisoning of Superconducting Qubits from Resonant Absorption of Pair-Breaking Photons

C. H. Liu, D. C. Harrison, S. Patel +8 more

The ideal superconductor provides a pristine environment for the delicate states of a quantum computer: because there is an energy gap to excitations, there are no spurious modes with which the qubits can interact, causing irreversible decay of the quantum state. As a practical matter, however, there exists a high density of excitations out of the superconducting ground state even at ultralow temperature; these are known as quasiparticles. Observed quasiparticle densities are of order 1 μm^{-3}, tens of orders of magnitude greater than the equilibrium density expected from theory. Nonequilibrium quasiparticles extract energy from the qubit mode and can induce dephasing. Here we show that a dominant mechanism for quasiparticle poisoning is direct absorption of high-energy photons at the qubit junction. We use a Josephson junction-based photon source to controllably dose qubit circuits with millimeter-wave radiation, and we use an interferometric quantum gate sequence to reconstruct the charge parity of the qubit. We find that the structure of the qubit itself acts as a resonant antenna for millimeter-wave radiation, providing an efficient path for photons to generate quasiparticles. A deep understanding of this physics will pave the way to realization of next-generation superconducting qubits that are robust against quasiparticle poisoning.

arXiv:2203.06577•Physical Review Letters•Jan 2, 2024•68 citations

Analysis of RF Surface Loss in a Planar 2D Qubit

Andrei Lunin, Mustafa Bal, Akshay A. Murthy +3 more

The Josephson junction and shunt capacitor form a transmon qubit, which is the cornerstone of modern quantum computing platforms. For reliable quantum computing, it is important how long a qubit can remain in a superposition of quantum states, which is determined by the coherence time (T1). The coherence time of a qubit effectively sets the "lifetime" of usable quantum information, determining how long quantum computations can be performed before errors occur and information is lost. There are several sources of decoherence in transmon qubits, but the predominant one is generally considered to be dielectric losses in the natural oxide layer formed on the surface of the superconductor. In this paper, we present a numerical study of microwave surface losses in planar superconducting antennas of different transmon qubit designs. An asymptotic method for estimating the energy participation ratio in ultrathin films of nanometer scales is proposed, and estimates are given for the limits of achievable minimum RF losses depending on the electrical properties of the surface oxide and the interface of the qubit with the substrate material.

arXiv:2507.18672•Jul 24, 2025•0 citations

Wiring surface loss of a superconducting transmon qubit

Nikita S. Smirnov, Elizaveta A. Krivko, Anastasiya A. Solovyova +2 more

Quantum processors using superconducting qubits suffer from dielectric loss leading to noise and dissipation. Qubits are usually designed as large capacitor pads connected to a non-linear Josephson junction (or SQUID) by a superconducting thin metal wiring. Here, we report on finite-element simulation and experimental results confirming that more than 50% of surface loss in transmon qubits can originate from Josephson junctions wiring and can limit qubit relaxation time. We experimentally extracted dielectric loss tangents of qubit elements and showed that dominant surface loss of wiring can occur for real qubits designs. Finally, we experimentally demonstrate up to 20% improvement in qubit quality factor by wiring design optimization.

arXiv:2311.16794•Scientific Reports•Mar 27, 2024•22 citations

Transmon qubits coupled to superconducting lumped element resonators

Baladitya Suri

I discuss the design, fabrication and measurement at millikelvin-temperatures of Al/AlO$_x$/Al Josephson junction-based transmon qubits coupled to superconducting thin-film lumped element microwave resonators made of aluminum on sapphire. The resonators had a center frequency of around $6\,$GHz, and a total quality factor ranging from 15,000 to 70,000 for the various devices. The area of the transmon junctions was about $150\, \mathrm{nm} \times 150\, \mathrm{nm}$ and with Josephson energy $E_J$ such that $10\,\text{GHz} \leq E_J / h \leq 30\,$GHz. The charging energy of the transmons arising mostly from the large interdigital shunt capacitance, was $E_c / h \approx 300\,$MHz. I present microwave spectroscopy of the devices in the strongly dispersive regime of circuit quantum electrodynamics. In this limit the ac Stark shift due to a single photon in the resonator is greater than the linewidth of the qubit transition. When the resonator is driven coherently using a coupler tone, the transmon spectrum reveals individual ``photon number'' peaks, each corresponding to a single additional photon in the resonator. Using a weighted average of the peak heights in the qubit spectrum, I calculated the average number of photons $\bar{n}$ in the resonator. I also observed a nonlinear variation of $\bar{n}$ with the applied power of the coupler tone $P_{rf}$. I studied this nonlinearity using numerical simulations and found good qualitative agreement with data. In the absence of a coherent drive on the resonator, a thermal population of $5.474\,$GHz photons in the resonator, at an effective temperature of $120\,$mK resulted in a weak $n=1$ thermal photon peak in the qubit spectrum. In the presence of independent coupler and probe tones, the $n=1$ thermal photon peak revealed an Autler-Townes splitting. The observed effect was explained accurately using the four lowest levels of the dispersively dressed Jaynes-Cummings transmon-resonator system, and numerical simulations of the steady-state master equation for the coupled system. I also present time-domain measurements on transmons coupled to lumped-element resonators. From $T_1$ and Rabi oscillation measurements, I found that my early transmon devices (called design LEv5) had lifetimes ($T_1 \sim 1\,\mu$s) limited by strong coupling to the $50\,\Omega$ transmission line. This coupling was characterized by the the rate of change of the Rabi oscillation frequency with the change in the drive voltage ($\mathrm{d}f_{Rabi}\, / \mathrm{d}V$) -- also termed the Rabi coupling to the drive. I studied the design of the transmon-resonator system using circuit analysis and microwave simulations with the aim being to reduce the Rabi coupling to the drive. By increasing the resonance frequency of the resonator $\omega_r/2\pi$ from 5.4$\,$GHz to 7.2$\,$GHz, lowering the coupling of the resonator to the transmission line and thereby increasing the external quality factor $Q_e$ from 20,000 to 70,000, and reducing the transmon-resonator coupling $g/2\pi$ from 70$\,$MHz to 40$\,$MHz, I reduced the Rabi coupling to the drive by an order of magnitude ($\sim$ factor of 20). The $T_1 \sim 4\,\mu$s of devices in the new design (LEv6) was longer than that of the early devices, but still much shorter than the lifetimes predicted from Rabi coupling, suggesting the presence of alternative sources of noise causing qubit relaxation. Microwave simulations and circuit analysis in the presence of a dielectric loss tangent $\tan \delta \simeq 5\times10^{-6}$ agree reasonably well with the measured $T_1$ values, suggesting that surface dielectric loss may be causing relaxation of transmons in the new designs.

•Jan 1, 2015•3 citations

Engineering superconducting qubits to reduce quasiparticles and charge noise

Xianchuang Pan, Yuxuan Zhou, Haolan Yuan +10 more

Identifying, quantifying, and suppressing decoherence mechanisms in qubits are important steps towards the goal of engineering a quantum computer or simulator. Superconducting circuits offer flexibility in qubit design; however, their performance is adversely affected by quasiparticles (broken Cooper pairs). Developing a quasiparticle mitigation strategy compatible with scalable, high-coherence devices is therefore highly desirable. Here we experimentally demonstrate how to control quasiparticle generation by downsizing the qubit, capping it with a metallic cover, and equipping it with suitable quasiparticle traps. Using a flip-chip design, we shape the electromagnetic environment of the qubit above the superconducting gap, inhibiting quasiparticle poisoning. Our findings support the hypothesis that quasiparticle generation is dominated by the breaking of Cooper pairs at the junction, as a result of photon absorption by the antenna-like qubit structure. We achieve record low charge-parity switching rate (<1 Hz). Our aluminium devices also display improved stability with respect to discrete charging events.

arXiv:2202.01435•Nature Communications•Nov 23, 2022•88 citations

Coupling a Superconducting Qubit to a Left-Handed Metamaterial Resonator

S. Indrajeet, H. Wang, M.D. Hutchings +4 more

Metamaterial resonant structures made from arrays of superconducting lumped-circuit elements can exhibit microwave-mode spectra with left-handed dispersion for the standing-wave resonances, resulting in a high density of modes in the same frequency range where superconducting qubits are typically operated, as well as a bandgap at lower frequencies that extends down to dc. Using this regime for multimode circuit quantum electrodynamics, we perform a series of measurements of such a superconducting metamaterial resonator coupled to a flux-tunable transmon qubit. Through microwave measurements of the metamaterial, we observe the coupling of the qubit to each of the modes that it passes through. Using a separate readout resonator, we probe the qubit dispersively and characterize the qubit energy relaxation as a function of frequency, which is strongly affected by the Purcell effect in the presence of the dense mode spectrum. Additionally, we investigate the ac Stark shift of the qubit as the photon number in the various metamaterial modes is varied. Through numerical simulations, we explore designs based on this scheme with enhanced coupling so that the coupling energy between the qubit and the metamaterial modes can exceed the intermode spacing in future devices with achievable circuit parameters. The ability to tailor the dense mode spectrum through the choice of circuit parameters and manipulate the photonic state of the metamaterial through interactions with qubits makes this a promising platform for analog quantum simulation with microwave photons and quantum memories.

arXiv:2007.10932•Physical Review Applied•Dec 10, 2020•22 citations
Superconducting qubits are resonant absorbers of pair-breaking radiation. The metal pads that form the qubit capacitance support standing wave modes at frequencies of order 100~GHz; these modes are strongly coupled to free-space impedance through their electric dipole moment. While the antenna mode of the 3D transmon qubit is easily seen to be a resonant dipole, other 2D qubit types can be understood as the aperture duals of wire loop antennas or folded dipoles. For typical Josephson junction parameters, the junction provides a reasonable conjugate match to the fundamental antenna mode. We calculate the contribution to quasiparticle poisoning from resonant absorption of blackbody radiation. We extend our analysis to dissipation at the qubit frequency, where radiative losses provide an ultimate limit to qubit energy relaxation time. A clear understanding of the spurious antenna modes of qubits will allow designs that are insensitive to pair-breaking radiation and that display reduced radiative losses at the qubit frequency.
The ideal superconductor provides a pristine environment for the delicate states of a quantum computer: because there is an energy gap to excitations, there are no spurious modes with which the qubits can interact, causing irreversible decay of the quantum state. As a practical matter, however, there exists a high density of excitations out of the superconducting ground state even at ultralow temperature; these are known as quasiparticles. Observed quasiparticle densities are of order 1 μm^{-3}, tens of orders of magnitude greater than the equilibrium density expected from theory. Nonequilibrium quasiparticles extract energy from the qubit mode and can induce dephasing. Here we show that a dominant mechanism for quasiparticle poisoning is direct absorption of high-energy photons at the qubit junction. We use a Josephson junction-based photon source to controllably dose qubit circuits with millimeter-wave radiation, and we use an interferometric quantum gate sequence to reconstruct the charge parity of the qubit. We find that the structure of the qubit itself acts as a resonant antenna for millimeter-wave radiation, providing an efficient path for photons to generate quasiparticles. A deep understanding of this physics will pave the way to realization of next-generation superconducting qubits that are robust against quasiparticle poisoning.
The Josephson junction and shunt capacitor form a transmon qubit, which is the cornerstone of modern quantum computing platforms. For reliable quantum computing, it is important how long a qubit can remain in a superposition of quantum states, which is determined by the coherence time (T1). The coherence time of a qubit effectively sets the "lifetime" of usable quantum information, determining how long quantum computations can be performed before errors occur and information is lost. There are several sources of decoherence in transmon qubits, but the predominant one is generally considered to be dielectric losses in the natural oxide layer formed on the surface of the superconductor. In this paper, we present a numerical study of microwave surface losses in planar superconducting antennas of different transmon qubit designs. An asymptotic method for estimating the energy participation ratio in ultrathin films of nanometer scales is proposed, and estimates are given for the limits of achievable minimum RF losses depending on the electrical properties of the surface oxide and the interface of the qubit with the substrate material.
Quantum processors using superconducting qubits suffer from dielectric loss leading to noise and dissipation. Qubits are usually designed as large capacitor pads connected to a non-linear Josephson junction (or SQUID) by a superconducting thin metal wiring. Here, we report on finite-element simulation and experimental results confirming that more than 50% of surface loss in transmon qubits can originate from Josephson junctions wiring and can limit qubit relaxation time. We experimentally extracted dielectric loss tangents of qubit elements and showed that dominant surface loss of wiring can occur for real qubits designs. Finally, we experimentally demonstrate up to 20% improvement in qubit quality factor by wiring design optimization.
I discuss the design, fabrication and measurement at millikelvin-temperatures of Al/AlOx_xx​/Al Josephson junction-based transmon qubits coupled to superconducting thin-film lumped element microwave resonators made of aluminum on sapphire. The resonators had a center frequency of around 6 6\,6GHz, and a total quality factor ranging from 15,000 to 70,000 for the various devices. The area of the transmon junctions was about 150 nm×150 nm150\, \mathrm{nm} \times 150\, \mathrm{nm}150nm×150nm and with Josephson energy EJE_JEJ​ such that 10 GHz≤EJ/h≤30 10\,\text{GHz} \leq E_J / h \leq 30\,10GHz≤EJ​/h≤30GHz. The charging energy of the transmons arising mostly from the large interdigital shunt capacitance, was Ec/h≈300 E_c / h \approx 300\,Ec​/h≈300MHz. I present microwave spectroscopy of the devices in the strongly dispersive regime of circuit quantum electrodynamics. In this limit the ac Stark shift due to a single photon in the resonator is greater than the linewidth of the qubit transition. When the resonator is driven coherently using a coupler tone, the transmon spectrum reveals individual ``photon number'' peaks, each corresponding to a single additional photon in the resonator. Using a weighted average of the peak heights in the qubit spectrum, I calculated the average number of photons nˉ\bar{n}nˉ in the resonator. I also observed a nonlinear variation of nˉ\bar{n}nˉ with the applied power of the coupler tone PrfP_{rf}Prf​. I studied this nonlinearity using numerical simulations and found good qualitative agreement with data. In the absence of a coherent drive on the resonator, a thermal population of 5.474 5.474\,5.474GHz photons in the resonator, at an effective temperature of 120 120\,120mK resulted in a weak n=1n=1n=1 thermal photon peak in the qubit spectrum. In the presence of independent coupler and probe tones, the n=1n=1n=1 thermal photon peak revealed an Autler-Townes splitting. The observed effect was explained accurately using the four lowest levels of the dispersively dressed Jaynes-Cummings transmon-resonator system, and numerical simulations of the steady-state master equation for the coupled system. I also present time-domain measurements on transmons coupled to lumped-element resonators. From T1T_1T1​ and Rabi oscillation measurements, I found that my early transmon devices (called design LEv5) had lifetimes (T1∼1 μT_1 \sim 1\,\muT1​∼1μs) limited by strong coupling to the 50 Ω50\,\Omega50Ω transmission line. This coupling was characterized by the the rate of change of the Rabi oscillation frequency with the change in the drive voltage (dfRabi /dV\mathrm{d}f_{Rabi}\, / \mathrm{d}VdfRabi​/dV) -- also termed the Rabi coupling to the drive. I studied the design of the transmon-resonator system using circuit analysis and microwave simulations with the aim being to reduce the Rabi coupling to the drive. By increasing the resonance frequency of the resonator ωr/2π\omega_r/2\piωr​/2π from 5.4 \,GHz to 7.2 \,GHz, lowering the coupling of the resonator to the transmission line and thereby increasing the external quality factor QeQ_eQe​ from 20,000 to 70,000, and reducing the transmon-resonator coupling g/2πg/2\pig/2π from 70 \,MHz to 40 \,MHz, I reduced the Rabi coupling to the drive by an order of magnitude (∼\sim∼ factor of 20). The T1∼4 μT_1 \sim 4\,\muT1​∼4μs of devices in the new design (LEv6) was longer than that of the early devices, but still much shorter than the lifetimes predicted from Rabi coupling, suggesting the presence of alternative sources of noise causing qubit relaxation. Microwave simulations and circuit analysis in the presence of a dielectric loss tangent tan⁡δ≃5×10−6\tan \delta \simeq 5\times10^{-6}tanδ≃5×10−6 agree reasonably well with the measured T1T_1T1​ values, suggesting that surface dielectric loss may be causing relaxation of transmons in the new designs.
Identifying, quantifying, and suppressing decoherence mechanisms in qubits are important steps towards the goal of engineering a quantum computer or simulator. Superconducting circuits offer flexibility in qubit design; however, their performance is adversely affected by quasiparticles (broken Cooper pairs). Developing a quasiparticle mitigation strategy compatible with scalable, high-coherence devices is therefore highly desirable. Here we experimentally demonstrate how to control quasiparticle generation by downsizing the qubit, capping it with a metallic cover, and equipping it with suitable quasiparticle traps. Using a flip-chip design, we shape the electromagnetic environment of the qubit above the superconducting gap, inhibiting quasiparticle poisoning. Our findings support the hypothesis that quasiparticle generation is dominated by the breaking of Cooper pairs at the junction, as a result of photon absorption by the antenna-like qubit structure. We achieve record low charge-parity switching rate (<1 Hz). Our aluminium devices also display improved stability with respect to discrete charging events.
Metamaterial resonant structures made from arrays of superconducting lumped-circuit elements can exhibit microwave-mode spectra with left-handed dispersion for the standing-wave resonances, resulting in a high density of modes in the same frequency range where superconducting qubits are typically operated, as well as a bandgap at lower frequencies that extends down to dc. Using this regime for multimode circuit quantum electrodynamics, we perform a series of measurements of such a superconducting metamaterial resonator coupled to a flux-tunable transmon qubit. Through microwave measurements of the metamaterial, we observe the coupling of the qubit to each of the modes that it passes through. Using a separate readout resonator, we probe the qubit dispersively and characterize the qubit energy relaxation as a function of frequency, which is strongly affected by the Purcell effect in the presence of the dense mode spectrum. Additionally, we investigate the ac Stark shift of the qubit as the photon number in the various metamaterial modes is varied. Through numerical simulations, we explore designs based on this scheme with enhanced coupling so that the coupling energy between the qubit and the metamaterial modes can exceed the intermode spacing in future devices with achievable circuit parameters. The ability to tailor the dense mode spectrum through the choice of circuit parameters and manipulate the photonic state of the metamaterial through interactions with qubits makes this a promising platform for analog quantum simulation with microwave photons and quantum memories.