Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2004.01380 · Optics Express

Scalable readout interface for superconducting nanowire single-photon detectors using AQFP and RSFQ logic families

Naoki Takeuchi, Fumihiro China, Shigehito Miki, Shigeyuki Miyajima, Masahiro Yabuno, Nobuyuki Yoshikawa, Hirotaka Terai

Published May 1, 2020• 24 citations
arXivHTMLPDF

Abstract

We propose a scalable readout interface for superconducting nanowire single-photon detector (SSPD) arrays, which we call the AQFP/RSFQ interface. This interface is composed of adiabatic quantum-flux-parametron (AQFP) and rapid single-flux-quantum (RSFQ) logic families. The AQFP part reads out the spatial information of an SSPD array via a single cable, and the RSFQ part reads out the temporal information via a single cable. The hybrid interface has high temporal resolution owing to low timing jitter in the operation of the RSFQ part. In addition, the hybrid interface achieves high circuit scalability because of low supply current in the operation of the AQFP part. Therefore, the hybrid interface is suitable for handling many-pixel SSPD arrays. We demonstrate a four-pixel SSPD array using the hybrid interface as proof of concept. The measurement results show that the hybrid interface can read out all of the pixels with a low error rate and low timing jitter.

DOI
10.1364/oe.392507

Related papers

Adiabatic quantum-flux-parametron interface for the readout of superconducting nanowire single-photon detectors

Naoki Takeuchi, Taro Yamashita, Shigeyuki Miyajima +3 more

We propose and demonstrate a low-power and low-current cryogenic readout interface for a superconducting nanowire single-photon detector (SSPD) using adiabatic quantum-flux-parametron (AQFP) logic. The AQFP readout interface samples and digitizes the current signal from an SSPD, generating binary output data in accordance with the detection behavior of the SSPD. We demonstrate the correct operation of an SSPD with the interface, where the AQFP readout interface and the SSPD are placed in separate 0.1-W Gifford–McMahon (GM) cryocoolers and are interconnected via coaxial cables. It was found that the temperature of the sample stage did not change even after the AQFP readout interface was turned on, which revealed that the AQFP readout interface uses sufficiently low power and current for a compact cryocooler.

Optics Express•Dec 15, 2017•21 citations

Demonstration of a Superconducting Nanowire Single-Photon Detector using Adiabatic Quantum-Flux-Parametron Logic in a 0.1-W Gifford-McMahon Cryocooler

Naoki Takeuchi, Taro Yamashita, Shigeyuki Miyajima +3 more

Superconducting nanowire single-photon detectors (SSPDs or SNSPDs) have superior performance and are thus used for many applications, such as quantum information and laser communications. Lately, much effort has been spent on the development of multi-pixel SSPD arrays to achieve single-photon-level imaging. SSPD arrays require efficient readout schemes that reduce the number of coaxial cables for reading out the SSPD pixels. In a previous study, we proposed a readout interface using adiabatic quantum-flux-parametron (AQFP) logic, which digitizes the information of an SSPD at cryogenic temperature. In this study, we show the first demonstration of an SSPD that is read out by the AQFP readout interface placed in the same 0.1-W Gifford-McMahon cryocooler. The measurement results show that the AQFP readout interface reads out the SSPD with low error rates. Also, it is found that the temperature of the sample stage does not change even after the AQFP readout interface is turned on, which indicates that the power and current required for the AQFP readout interface are sufficiently low for the implementation using a compact cryocooler.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•5 citations

Cryogenic readout of superconducting nanowire single-photon detectors using high-sensitivity adiabatic quantum-flux-parametron circuits

Fumihiro China, Naoki Takeuchi, Shigehito Miki +3 more

Abstract We have been developing readout interfaces for superconducting nanowire single-photon detectors (SSPDs) using adiabatic quantum-flux-parametron (AQFP) logic. AQFP circuits operate with low power consumption, low bias currents, and high sensitivity, and thus are suitable as readout interfaces for large SSPD arrays. In this study, we develop a high-sensitivity AQFP interface, consisting of a current transformer, comparator, and rising-edge detector. We systematically investigated the current sensitivity of the AQFP interface by operating an NbTiN SSPD with the interface in a 0.1 W Gifford–McMahon cryocooler. We compared the outputs from the AQFP interface with the direct outputs from the SSPD, thereby demonstrating a sensitivity of 3.5 μ A, which is much smaller than that of the single-flux-quantum interfaces that we developed before.

Superconductor Science and Technology•Feb 18, 2021•7 citations

Scalable implementation of a superconducting nanowire single-photon detector array with a superconducting digital signal processor

Masahiro Yabuno, Shigeyuki Miyajima, Shigehito Miki +1 more

A two-dimensional single-photon imaging system with high sensitivity and high time resolution is the ultimate camera and useful in a wide range of fields. A superconducting nanowire single-photon detector (SSPD or SNSPD) is one of the best candidates for realizing such an ultimate camera due to its high detection efficiency in a wide spectral range, low dark count rate without after-pulsing, and excellent time resolution. Here we propose a new readout scheme to realize a large-scale imaging array based on SSPD, where a row-column readout architecture is combined with a digital signal processor based on a single-flux-quantum (SFQ) circuit. A 16-pixel row-column readout SSPD array is fabricated and measured with an SFQ digital signal processor. We successfully acquired spatial information as encoded digital bit codes with the temporal information of the photon detection. The system timing jitter was measured as <80 ps for all 16 pixels even through the SFQ signal processor, indicating the potential for an imaging array with an extremely high time resolution.

Optics Express•Apr 1, 2020•40 citations

Technologies for superconducting nanowire single-photon detector array system

Shigehito Miki, Taro Yamashita, Hirotaka Terai +2 more

We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 3, 2013•1 citation

Crosstalk-free operation of multielement superconducting nanowire single-photon detector array integrated with single-flux-quantum circuit in a 01 W Gifford–McMahon cryocooler

Taro Yamashita, Shigehito Miki, Hirotaka Terai +2 more

We demonstrate the successful operation of a multielement superconducting nanowire single-photon detector (SSPD) array integrated with a single-flux-quantum (SFQ) readout circuit in a compact 0.1 W Gifford-McMahon cryocooler. A time-resolved readout technique, where output signals from each element enter the SFQ readout circuit with finite time intervals, revealed crosstalk-free operation of the four-element SSPD array connected with the SFQ readout circuit. The timing jitter and the system detection efficiency were measured to be 50 ps and 11.4%, respectively, which were comparable to the performance of practical single-pixel SSPD systems.

Optics Letters•Jul 13, 2012•48 citations
We propose a scalable readout interface for superconducting nanowire single-photon detector (SSPD) arrays, which we call the AQFP/RSFQ interface. This interface is composed of adiabatic quantum-flux-parametron (AQFP) and rapid single-flux-quantum (RSFQ) logic families. The AQFP part reads out the spatial information of an SSPD array via a single cable, and the RSFQ part reads out the temporal information via a single cable. The hybrid interface has high temporal resolution owing to low timing jitter in the operation of the RSFQ part. In addition, the hybrid interface achieves high circuit scalability because of low supply current in the operation of the AQFP part. Therefore, the hybrid interface is suitable for handling many-pixel SSPD arrays. We demonstrate a four-pixel SSPD array using the hybrid interface as proof of concept. The measurement results show that the hybrid interface can read out all of the pixels with a low error rate and low timing jitter.
We propose and demonstrate a low-power and low-current cryogenic readout interface for a superconducting nanowire single-photon detector (SSPD) using adiabatic quantum-flux-parametron (AQFP) logic. The AQFP readout interface samples and digitizes the current signal from an SSPD, generating binary output data in accordance with the detection behavior of the SSPD. We demonstrate the correct operation of an SSPD with the interface, where the AQFP readout interface and the SSPD are placed in separate 0.1-W Gifford–McMahon (GM) cryocoolers and are interconnected via coaxial cables. It was found that the temperature of the sample stage did not change even after the AQFP readout interface was turned on, which revealed that the AQFP readout interface uses sufficiently low power and current for a compact cryocooler.
Superconducting nanowire single-photon detectors (SSPDs or SNSPDs) have superior performance and are thus used for many applications, such as quantum information and laser communications. Lately, much effort has been spent on the development of multi-pixel SSPD arrays to achieve single-photon-level imaging. SSPD arrays require efficient readout schemes that reduce the number of coaxial cables for reading out the SSPD pixels. In a previous study, we proposed a readout interface using adiabatic quantum-flux-parametron (AQFP) logic, which digitizes the information of an SSPD at cryogenic temperature. In this study, we show the first demonstration of an SSPD that is read out by the AQFP readout interface placed in the same 0.1-W Gifford-McMahon cryocooler. The measurement results show that the AQFP readout interface reads out the SSPD with low error rates. Also, it is found that the temperature of the sample stage does not change even after the AQFP readout interface is turned on, which indicates that the power and current required for the AQFP readout interface are sufficiently low for the implementation using a compact cryocooler.
Abstract We have been developing readout interfaces for superconducting nanowire single-photon detectors (SSPDs) using adiabatic quantum-flux-parametron (AQFP) logic. AQFP circuits operate with low power consumption, low bias currents, and high sensitivity, and thus are suitable as readout interfaces for large SSPD arrays. In this study, we develop a high-sensitivity AQFP interface, consisting of a current transformer, comparator, and rising-edge detector. We systematically investigated the current sensitivity of the AQFP interface by operating an NbTiN SSPD with the interface in a 0.1 W Gifford–McMahon cryocooler. We compared the outputs from the AQFP interface with the direct outputs from the SSPD, thereby demonstrating a sensitivity of 3.5 μ A, which is much smaller than that of the single-flux-quantum interfaces that we developed before.
A two-dimensional single-photon imaging system with high sensitivity and high time resolution is the ultimate camera and useful in a wide range of fields. A superconducting nanowire single-photon detector (SSPD or SNSPD) is one of the best candidates for realizing such an ultimate camera due to its high detection efficiency in a wide spectral range, low dark count rate without after-pulsing, and excellent time resolution. Here we propose a new readout scheme to realize a large-scale imaging array based on SSPD, where a row-column readout architecture is combined with a digital signal processor based on a single-flux-quantum (SFQ) circuit. A 16-pixel row-column readout SSPD array is fabricated and measured with an SFQ digital signal processor. We successfully acquired spatial information as encoded digital bit codes with the temporal information of the photon detection. The system timing jitter was measured as <80 ps for all 16 pixels even through the SFQ signal processor, indicating the potential for an imaging array with an extremely high time resolution.
We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.
We demonstrate the successful operation of a multielement superconducting nanowire single-photon detector (SSPD) array integrated with a single-flux-quantum (SFQ) readout circuit in a compact 0.1 W Gifford-McMahon cryocooler. A time-resolved readout technique, where output signals from each element enter the SFQ readout circuit with finite time intervals, revealed crosstalk-free operation of the four-element SSPD array connected with the SFQ readout circuit. The timing jitter and the system detection efficiency were measured to be 50 ps and 11.4%, respectively, which were comparable to the performance of practical single-pixel SSPD systems.