We present an on-chip superconducting filter bank spectrometer based on transition-edge sensors (TES) as a technology for realising a microwave atmospheric sounding instrument with several hundred channels and sky- noise limited performance. Each device consists of a wideband feed coupled to a transmission line filter bank, with a TES behind each filter. In the first instance we have targeted atmospheric temperature sounding using the oxygen (O2) absorption line at 60 GHz, however the device is being scaled to 180 GHz for humidity sounding. The technology developed is also generally applicable to astronomical instrumentation. We have fabricated a set of test devices to demonstrate key device technologies, such as channel placement, spectral resolution and sensitivity. We will describe device design, test configuration and results.
Abstract Superconducting on-chip filter banks provide a scalable, space saving solution to create imaging spectrometers at millimetre and submillimetre wavelengths. We present an easy to realise, lithographed superconducting filter design with a high tolerance to fabrication error. Using a capacitively coupled
λ/2 λ / 2 microstrip resonator to define a narrow (
λ/Δλ=300 λ / Δ λ = 300 ) spectral pass band, the filtered output of a given spectrometer channel directly connects to a lumped-element kinetic inductance detector. We show the tolerance analysis of our design, demonstrating
<11% < 11 % change in filter quality factor to any one realistic fabrication error and a full filter-bank efficiency forecast to be 50% after accounting for fabrication errors and dielectric loss tangent.
The balloon-borne instrument TELIS (TErahertz and submillimetre LImb Sounder) is a three-channel superconducting heterodyne spectrometer for atmospheric research use. It detects spectral emission lines of stratospheric trace gases that have their rotational transitions at THz frequencies. One of the channels is based on the superconducting integrated receiver (SIR) technology. We demonstrate for the first time the capabilities of the SIR technology for heterodyne spectroscopy in general, and atmospheric limb sounding in particular. We also show that the application of SIR technology is not limited to laboratory environments, but that it is well suited for remote operation under harsh environmental conditions. Within a SIR the main components needed for a superconducting heterodyne receiver such as a superconductor–insulator–superconductor (SIS) mixer with a quasi-optical antenna, a flux-flow oscillator (FFO) as the local oscillator, and a harmonic mixer to phase lock the FFO are integrated on a single chip. Light weight and low power consumption combined with broadband operation and nearly quantum limited sensitivity make the SIR a perfect candidate for use in future airborne and space-borne missions. The noise temperature of the SIR was measured to be as low as 120 K, with an intermediate frequency band of 4–8 GHz in double-sideband operation. The spectral resolution is well below 1 MHz, confirmed by our measurements. Remote control of the SIR under flight conditions has been demonstrated in a successful balloon flight in Kiruna, Sweden. The sensor and instrument design are presented, as well as the preliminary science results from the first flight.
We present a high efficiency, moderate resolution on-chip superconducting filterbank spectrometer designed for line intensity mapping and broadband wave-like dark matter searches. Existing implementations used by the millimeter-wave community rely on resistive feedline termination for standing wave mitigation which caps the per-channel efficiency
ηch at 50\% and utilize microstrip resonators which highly couple the resolving power
R=ν/δν and
ηch to thin-film dielectric loss. The architecture presented in this paper addresses these limitations by eliminating the termination resistor and employing niobium coplanar waveguide resonators patterned directly on single-crystal silicon, which fixes the resonator's internal quality factor by the silicon substrate property rather than by the loss tangent of a deposited film. The resolving power is set by the impedance ratio between the resonator and feedline. Electromagnetic and circuit simulations of a ten-channel filterbank near 90~GHz at unity oversampling show
R=1170 and
ηch>78%, with no significant trend in efficiency across channels. A ten-channel prototype, designed for
R=92±5 and
ηch=(81±3)% over 90--106~GHz with a 560~nm interlayer based on simulations, was fabricated and optically characterized, yielding
R=208±74 and
ηch=(77±6)%. Measured
ηch well above the 50\% termination limit, together with demonstrated impedance tuning of
R, validate the design principles of this filterbank spectrometer and establishes a route to high-efficiency, high-resolution on-chip spectrometer arrays.
The opacity due to water vapor in the Earth's atmosphere obscures portions of the sub-THz spectrum (mm/sub-mm wavelengths) to ground based astronomical observation. For maximum sensitivity, instruments operating at these wavelengths must be designed to have spectral responses that match the available windows in the atmospheric transmission that occur in between the strong water absorption lines. Traditionally, the spectral response of mm/sub-mm instruments has been set using optical, metal-mesh bandpass filters [1]. An alternative method for defining the passbands, available when using superconducting detectors coupled with planar antennas, is to use on-chip, superconducting filters [2]. This paper presents the design and testing of superconducting, lumped element, on-chip bandpass filters (BPFs), placed inline with the microstrip connecting the antenna and the detector, covering the frequency range from 209-416 GHz. Four filters were designed with pass bands 209-274 GHz, 265-315 GHz, 335-361 GHz and 397-416 GHz corresponding to the atmospheric transmission windows. Fourier transform spectroscopy was used to verify that the spectral response of the BPFs is well predicted by the computer simulations. Two-color operation of the pixels was demonstrated by connecting two detectors to a single broadband antenna through two BPFs. Scalability of the design to multiple (four) colors is discussed.
Abstract The readout system with a high multiplexing ratio has become a bottleneck limiting the application of large-scale Transition Edge Sensor (TES) detector arrays. In recent years, the microwave superconducting quantum interference device (SQUID) multiplexer has emerged as a key technology for effectively reading large-scale cryogenic detector arrays. Currently, the microwave SQUID multiplexer is being adopted by an increasing number of experiments due to its capability of achieving a multiplexing ratio of 2000:1 within the readout bandwidth. In this study, we developed a 32-channel microwave SQUID multiplexer prototype. And we measured 8 channels of the prototype. The measured equivalent noise current of the prototype reached 154 pA/√ Hz.