Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Millimeter-Wave Lumped Element Superconducting Bandpass Filters for Multi-Color Imaging

S. Kumar, Anastasios Vayonakis, Henry George LeDuc, Peter K. Day, S. R. Golwala, Jonas Stasys Zmuidzinas

Published May 27, 2009• 15 citations
Publisher

Abstract

The opacity due to water vapor in the Earth's atmosphere obscures portions of the sub-THz spectrum (mm/sub-mm wavelengths) to ground based astronomical observation. For maximum sensitivity, instruments operating at these wavelengths must be designed to have spectral responses that match the available windows in the atmospheric transmission that occur in between the strong water absorption lines. Traditionally, the spectral response of mm/sub-mm instruments has been set using optical, metal-mesh bandpass filters [1]. An alternative method for defining the passbands, available when using superconducting detectors coupled with planar antennas, is to use on-chip, superconducting filters [2]. This paper presents the design and testing of superconducting, lumped element, on-chip bandpass filters (BPFs), placed inline with the microstrip connecting the antenna and the detector, covering the frequency range from 209-416 GHz. Four filters were designed with pass bands 209-274 GHz, 265-315 GHz, 335-361 GHz and 397-416 GHz corresponding to the atmospheric transmission windows. Fourier transform spectroscopy was used to verify that the spectral response of the BPFs is well predicted by the computer simulations. Two-color operation of the pixels was demonstrated by connecting two detectors to a single broadband antenna through two BPFs. Scalability of the design to multiple (four) colors is discussed.

DOI
10.1109/tasc.2009.2017884

Related papers

Miniaturization of superconducting passive filters for on-chip applications

Raihan Rafique, Peter Linnér, Bahar M. Motlagh +3 more

We present techniques to miniaturize superconducting ultra narrowband filters for on-chip applications. The filters are designed for 2 GHz, 5 GHz and 10 GHz operating frequencies. The expected bandwidths of the designed filters are 2-20 MHz. The designs are of 7 stages Chebyshev filters having maximum passband ripples of 0.5 dB. On-chip filters are particularly interesting as they are applicable for monolithic design with the RSFQ circuit aiming qubit applications. One of the designs is a quasi-lumped filter where the effective wave propagation constant has been increased by the addition of lumped components to the superconducting microstrip line (SMSL). Additionally, this design provides the optimum width of an SMSL without violating design rules. The other design consists of distributed and lumped components. The area of the filter is in the range of 1-2 square mm. We present the filter topologies and corresponding experimental results for the frequency response of these on-chip filters designed for Hypres 4.5 kA/cm2 fabrication process.

•Jan 1, 2007•1 citation

Superconducting Integrated Circuits at Sub-millimeter Wavelengths

Sebastian Hähnle

Superconducting integrated circuits (SICs) represent a natural step forward for devices operating at frequencies from microwave up to sub-millimeter wavelengths. They offer massive miniaturization via compact design based on low-loss superconducting transmission lines. At sub-millimeter wavelengths, the development of SICs is driven by astronomical instruments where it could allow the realization of an imaging spectrometer, combining simultaneous imaging and spectroscopy capabilities into a single instrument analogous to integral field units in the infrared and optical regimes. Such an imaging spectrometer can be achieved with SICs by integrating the required elements, such as spectral filters and polarizers, with the detectors onto a single chip. Without this integration, the dispersive system for even a single spatial pixel at these wavelengths would be prohibitively large and could not be realistically scaled up to allow imaging. Astronomical signals are exceedingly weak, typically requiring many nights of exposure to get a good signal to noise ratio. It is therefore imperative that the instrument has minimal losses before its detectors. As a consequence, the losses of each element in the SIC needs to be minimized, which requires careful characterization of the individual elements, including antenna, filters, detectors and connecting transmission lines. The primary focus of this thesis lies on the experimental characterization of the wideband antenna and the low-loss superconducting transmission lines.

•Oct 5, 2021•0 citations

Superconducting Microwave Filters

Sormeh Setoodeh

Superconducting microelectronics (SME) technology has the potential of realizing very high speed digital receivers capable of performing direct digitization of radio frequency signals with very low power consumption. The SME receiver is implemented on a single chip using Niobium based low temperature superconductive (LTS) Josephson Junction (JJ) technology by HYPRES. Analogue RF filters are still required at the receiver front end and are key components of the overall superconductor digital receiver. SME receivers usually require two types of RF filters; a wideband bandpass filter and a bandstop filter (a notch filter). The notch filter is required to eliminate interference and unwanted signals in the passband. In this thesis, design of highly miniaturized lumped element wideband and bandstop filters is investigated and some challenges are addressed. The filters are fabricated by the HYPRES process and therefore can be integrated with the SME receiver on the same chip. \nIn a wideband filter, the coupling between the adjacent resonators is high. Achieving such a strong coupling is one of the challenges of designing wideband filters. The wideband filters realized with distributed elements usually suffer from very low spurious frequency. As the bandwidth of the filter becomes wider, the spurious peak of the second harmonic gets closer to the passband of the filter. In the first part of this work, the possibility of realizing lumped element superconducting bandpass filters (BPF) with a relative bandwidth of 80% is investigated. \nIn the second part of the thesis, design and realization of lumped element superconducting bandstop filters (BSF) is discussed. The challenge for designing a bandstop filter is providing a good match over a wide frequency range. So narrowband inverters cannot be used. Instead, usually λ/4 matched transmission lines provide 90° phase shift between the resonators of a notch filter. The possibility of replacing the long transmission line with other means or eliminating the inverters and using both shunt and series resonators are investigated. Having both series and shunt resonators introduces some new challenges that are addressed in the thesis and discussed thoroughly. \nA tunable notch resonator is presented. The tunability is provided by a superconducting MEMS varactor that is realized in our group by doing some post processing on the device fabricated by HYPRES. The tunability range of the device at cryogenic temperatures is investigated. A 3-pole tunable BSF is also designed that uses the same tunable resonators. The tunability of the filter is investigated through simulation.

•Feb 22, 2011•3 citations

Sharp-selectivity in-line topology low temperature superconducting bandpass filter for superconducting quantum applications

Yuxing He, Shiori Michibayashi, Naoki Takeuchi +1 more

Abstract This paper presents a new class of sharp-selectivity low-temperature superconducting filter that incorporates lumped element resonant couplings. Dependent on a novel synthesis approach, the proposed filter exhibits great advantages such as: (1) a very simple in-line topology (without any cross coupling), (2) extremely compact size based on lumped inductor-capacitor (LC) elements, and (3) multiple transmission zeros (TZs) independently generated and controlled (via each resonant coupling). To facilitate the physical implementation, a group of lumped element circuit models are detailed, where series LC units are adopted for both the resonators and the resonant couplings. Considering an in-line topology here, the entire filter layout is then designed by cascading the lumped models one after another. For verification, a 5th-order bandpass filter centered at 5 GHz, with 500 MHz bandwidth and 3 TZs, is designed, simulated, and tested at cryogenic temperature (4.2 K). Moreover, preliminary simulations of the presented filter in series with an on-chip rapid single-flux-quantum microwave pulse generator are discussed for superconducting quantum applications.

Superconductor Science and Technology•Jan 22, 2020•11 citations

Miniaturized superconducting microwave filters

M R Rafique, Thomas Ohki, Biddut Kumar Banik +3 more

In this paper we present methods for the miniaturization of superconducting filters. We consider two designs of seventh-order bandpass Chebyshev filters based on lumped elements and a novel quasi-lumped element resonator. In both designs the area of the filters, with a central frequency of 2–5 GHz, is less than 1.2 mm 2 . Such small filters can be readily integrated on a single board for multi-channel microwave control of superconducting qubits. The filters have been experimentally tested and the results are compared with simulations. The miniaturization resulted in parasitic coupling between resonators and within each resonator that affected primarily the stopband and increased the bandwidth. The severity of the error depends on the design in particular, and was less sensitive when a groundplane was used under the inductances of the resonators. The best performance was reached for the quasi-lumped filter with central frequency of 4.45 GHz, quality factor of 40 and 50 dB stopband.

Superconductor Science and Technology•Apr 16, 2008•14 citations

A millimeter-wave on-chip superconducting filter bank spectrometer for atmospheric science

A. Orlando, Chris Thomas, D. J. Goldie +4 more

We present an on-chip superconducting filter bank spectrometer based on transition-edge sensors (TES) as a technology for realising a microwave atmospheric sounding instrument with several hundred channels and sky- noise limited performance. Each device consists of a wideband feed coupled to a transmission line filter bank, with a TES behind each filter. In the first instance we have targeted atmospheric temperature sounding using the oxygen (O2) absorption line at 60 GHz, however the device is being scaled to 180 GHz for humidity sounding. The technology developed is also generally applicable to astronomical instrumentation. We have fabricated a set of test devices to demonstrate key device technologies, such as channel placement, spectral resolution and sensitivity. We will describe device design, test configuration and results.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Dec 12, 2020•1 citation
The opacity due to water vapor in the Earth's atmosphere obscures portions of the sub-THz spectrum (mm/sub-mm wavelengths) to ground based astronomical observation. For maximum sensitivity, instruments operating at these wavelengths must be designed to have spectral responses that match the available windows in the atmospheric transmission that occur in between the strong water absorption lines. Traditionally, the spectral response of mm/sub-mm instruments has been set using optical, metal-mesh bandpass filters [1]. An alternative method for defining the passbands, available when using superconducting detectors coupled with planar antennas, is to use on-chip, superconducting filters [2]. This paper presents the design and testing of superconducting, lumped element, on-chip bandpass filters (BPFs), placed inline with the microstrip connecting the antenna and the detector, covering the frequency range from 209-416 GHz. Four filters were designed with pass bands 209-274 GHz, 265-315 GHz, 335-361 GHz and 397-416 GHz corresponding to the atmospheric transmission windows. Fourier transform spectroscopy was used to verify that the spectral response of the BPFs is well predicted by the computer simulations. Two-color operation of the pixels was demonstrated by connecting two detectors to a single broadband antenna through two BPFs. Scalability of the design to multiple (four) colors is discussed.
We present techniques to miniaturize superconducting ultra narrowband filters for on-chip applications. The filters are designed for 2 GHz, 5 GHz and 10 GHz operating frequencies. The expected bandwidths of the designed filters are 2-20 MHz. The designs are of 7 stages Chebyshev filters having maximum passband ripples of 0.5 dB. On-chip filters are particularly interesting as they are applicable for monolithic design with the RSFQ circuit aiming qubit applications. One of the designs is a quasi-lumped filter where the effective wave propagation constant has been increased by the addition of lumped components to the superconducting microstrip line (SMSL). Additionally, this design provides the optimum width of an SMSL without violating design rules. The other design consists of distributed and lumped components. The area of the filter is in the range of 1-2 square mm. We present the filter topologies and corresponding experimental results for the frequency response of these on-chip filters designed for Hypres 4.5 kA/cm2 fabrication process.
Superconducting integrated circuits (SICs) represent a natural step forward for devices operating at frequencies from microwave up to sub-millimeter wavelengths. They offer massive miniaturization via compact design based on low-loss superconducting transmission lines. At sub-millimeter wavelengths, the development of SICs is driven by astronomical instruments where it could allow the realization of an imaging spectrometer, combining simultaneous imaging and spectroscopy capabilities into a single instrument analogous to integral field units in the infrared and optical regimes. Such an imaging spectrometer can be achieved with SICs by integrating the required elements, such as spectral filters and polarizers, with the detectors onto a single chip. Without this integration, the dispersive system for even a single spatial pixel at these wavelengths would be prohibitively large and could not be realistically scaled up to allow imaging. Astronomical signals are exceedingly weak, typically requiring many nights of exposure to get a good signal to noise ratio. It is therefore imperative that the instrument has minimal losses before its detectors. As a consequence, the losses of each element in the SIC needs to be minimized, which requires careful characterization of the individual elements, including antenna, filters, detectors and connecting transmission lines. The primary focus of this thesis lies on the experimental characterization of the wideband antenna and the low-loss superconducting transmission lines.
Superconducting microelectronics (SME) technology has the potential of realizing very high speed digital receivers capable of performing direct digitization of radio frequency signals with very low power consumption. The SME receiver is implemented on a single chip using Niobium based low temperature superconductive (LTS) Josephson Junction (JJ) technology by HYPRES. Analogue RF filters are still required at the receiver front end and are key components of the overall superconductor digital receiver. SME receivers usually require two types of RF filters; a wideband bandpass filter and a bandstop filter (a notch filter). The notch filter is required to eliminate interference and unwanted signals in the passband. In this thesis, design of highly miniaturized lumped element wideband and bandstop filters is investigated and some challenges are addressed. The filters are fabricated by the HYPRES process and therefore can be integrated with the SME receiver on the same chip. \nIn a wideband filter, the coupling between the adjacent resonators is high. Achieving such a strong coupling is one of the challenges of designing wideband filters. The wideband filters realized with distributed elements usually suffer from very low spurious frequency. As the bandwidth of the filter becomes wider, the spurious peak of the second harmonic gets closer to the passband of the filter. In the first part of this work, the possibility of realizing lumped element superconducting bandpass filters (BPF) with a relative bandwidth of 80% is investigated. \nIn the second part of the thesis, design and realization of lumped element superconducting bandstop filters (BSF) is discussed. The challenge for designing a bandstop filter is providing a good match over a wide frequency range. So narrowband inverters cannot be used. Instead, usually λ/4 matched transmission lines provide 90° phase shift between the resonators of a notch filter. The possibility of replacing the long transmission line with other means or eliminating the inverters and using both shunt and series resonators are investigated. Having both series and shunt resonators introduces some new challenges that are addressed in the thesis and discussed thoroughly. \nA tunable notch resonator is presented. The tunability is provided by a superconducting MEMS varactor that is realized in our group by doing some post processing on the device fabricated by HYPRES. The tunability range of the device at cryogenic temperatures is investigated. A 3-pole tunable BSF is also designed that uses the same tunable resonators. The tunability of the filter is investigated through simulation.
Abstract This paper presents a new class of sharp-selectivity low-temperature superconducting filter that incorporates lumped element resonant couplings. Dependent on a novel synthesis approach, the proposed filter exhibits great advantages such as: (1) a very simple in-line topology (without any cross coupling), (2) extremely compact size based on lumped inductor-capacitor (LC) elements, and (3) multiple transmission zeros (TZs) independently generated and controlled (via each resonant coupling). To facilitate the physical implementation, a group of lumped element circuit models are detailed, where series LC units are adopted for both the resonators and the resonant couplings. Considering an in-line topology here, the entire filter layout is then designed by cascading the lumped models one after another. For verification, a 5th-order bandpass filter centered at 5 GHz, with 500 MHz bandwidth and 3 TZs, is designed, simulated, and tested at cryogenic temperature (4.2 K). Moreover, preliminary simulations of the presented filter in series with an on-chip rapid single-flux-quantum microwave pulse generator are discussed for superconducting quantum applications.
In this paper we present methods for the miniaturization of superconducting filters. We consider two designs of seventh-order bandpass Chebyshev filters based on lumped elements and a novel quasi-lumped element resonator. In both designs the area of the filters, with a central frequency of 2–5 GHz, is less than 1.2 mm 2 . Such small filters can be readily integrated on a single board for multi-channel microwave control of superconducting qubits. The filters have been experimentally tested and the results are compared with simulations. The miniaturization resulted in parasitic coupling between resonators and within each resonator that affected primarily the stopband and increased the bandwidth. The severity of the error depends on the design in particular, and was less sensitive when a groundplane was used under the inductances of the resonators. The best performance was reached for the quasi-lumped filter with central frequency of 4.45 GHz, quality factor of 40 and 50 dB stopband.
We present an on-chip superconducting filter bank spectrometer based on transition-edge sensors (TES) as a technology for realising a microwave atmospheric sounding instrument with several hundred channels and sky- noise limited performance. Each device consists of a wideband feed coupled to a transmission line filter bank, with a TES behind each filter. In the first instance we have targeted atmospheric temperature sounding using the oxygen (O2) absorption line at 60 GHz, however the device is being scaled to 180 GHz for humidity sounding. The technology developed is also generally applicable to astronomical instrumentation. We have fabricated a set of test devices to demonstrate key device technologies, such as channel placement, spectral resolution and sensitivity. We will describe device design, test configuration and results.