Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Sharp-selectivity in-line topology low temperature superconducting bandpass filter for superconducting quantum applications

Yuxing He, Shiori Michibayashi, Naoki Takeuchi, Nobuyuki Yoshikawa

Published Jan 22, 2020• 11 citations
Publisher

Abstract

Abstract This paper presents a new class of sharp-selectivity low-temperature superconducting filter that incorporates lumped element resonant couplings. Dependent on a novel synthesis approach, the proposed filter exhibits great advantages such as: (1) a very simple in-line topology (without any cross coupling), (2) extremely compact size based on lumped inductor-capacitor (LC) elements, and (3) multiple transmission zeros (TZs) independently generated and controlled (via each resonant coupling). To facilitate the physical implementation, a group of lumped element circuit models are detailed, where series LC units are adopted for both the resonators and the resonant couplings. Considering an in-line topology here, the entire filter layout is then designed by cascading the lumped models one after another. For verification, a 5th-order bandpass filter centered at 5 GHz, with 500 MHz bandwidth and 3 TZs, is designed, simulated, and tested at cryogenic temperature (4.2 K). Moreover, preliminary simulations of the presented filter in series with an on-chip rapid single-flux-quantum microwave pulse generator are discussed for superconducting quantum applications.

DOI
10.1088/1361-6668/ab6ec1

Related papers

Quasi-lumped Element Bandpass Filter for a Low-Temperature Superconducting Qubit Control-Pulse Generator

Yu Zeng, Yuxing He, Hongxiang Shen +1 more

This paper discusses a class of filters utilized in a low-power superconductor rapid single-flux-quantum (rapid SFQ, RSFQ) microwave pulse generator for controlling quantum bits (qubits). Here, the filter plays an important role to convert SFQ pulse trains (generated by RSFQ digital gates) and output a microwave control pulse. Characteristic of the output pulse can be adjusted by the in-band and roll-off performances of the filter, which is analyzed through numerical examples. Moreover, a novel in-line topology lumped network is proposed for the filter implementation, which can satisfy complex terminal cases at source (connecting an RSFQ digital block) and load (connecting a qubit). For the validation, we carry out a fourth-order bandpass filter using multilayer niobium (Nb) then-film technology, then incorporate it into an RSFQ control-pulse generator, and finally confirm correct functionality by both simulation and measurement.

Asia-Pacific Microwave Conference (APMC)•Dec 5, 2023•0 citations

Superconducting Microwave Filters

Sormeh Setoodeh

Superconducting microelectronics (SME) technology has the potential of realizing very high speed digital receivers capable of performing direct digitization of radio frequency signals with very low power consumption. The SME receiver is implemented on a single chip using Niobium based low temperature superconductive (LTS) Josephson Junction (JJ) technology by HYPRES. Analogue RF filters are still required at the receiver front end and are key components of the overall superconductor digital receiver. SME receivers usually require two types of RF filters; a wideband bandpass filter and a bandstop filter (a notch filter). The notch filter is required to eliminate interference and unwanted signals in the passband. In this thesis, design of highly miniaturized lumped element wideband and bandstop filters is investigated and some challenges are addressed. The filters are fabricated by the HYPRES process and therefore can be integrated with the SME receiver on the same chip. \nIn a wideband filter, the coupling between the adjacent resonators is high. Achieving such a strong coupling is one of the challenges of designing wideband filters. The wideband filters realized with distributed elements usually suffer from very low spurious frequency. As the bandwidth of the filter becomes wider, the spurious peak of the second harmonic gets closer to the passband of the filter. In the first part of this work, the possibility of realizing lumped element superconducting bandpass filters (BPF) with a relative bandwidth of 80% is investigated. \nIn the second part of the thesis, design and realization of lumped element superconducting bandstop filters (BSF) is discussed. The challenge for designing a bandstop filter is providing a good match over a wide frequency range. So narrowband inverters cannot be used. Instead, usually λ/4 matched transmission lines provide 90° phase shift between the resonators of a notch filter. The possibility of replacing the long transmission line with other means or eliminating the inverters and using both shunt and series resonators are investigated. Having both series and shunt resonators introduces some new challenges that are addressed in the thesis and discussed thoroughly. \nA tunable notch resonator is presented. The tunability is provided by a superconducting MEMS varactor that is realized in our group by doing some post processing on the device fabricated by HYPRES. The tunability range of the device at cryogenic temperatures is investigated. A 3-pole tunable BSF is also designed that uses the same tunable resonators. The tunability of the filter is investigated through simulation.

•Feb 22, 2011•3 citations

Miniaturized superconducting microwave filters

M R Rafique, Thomas Ohki, Biddut Kumar Banik +3 more

In this paper we present methods for the miniaturization of superconducting filters. We consider two designs of seventh-order bandpass Chebyshev filters based on lumped elements and a novel quasi-lumped element resonator. In both designs the area of the filters, with a central frequency of 2–5 GHz, is less than 1.2 mm 2 . Such small filters can be readily integrated on a single board for multi-channel microwave control of superconducting qubits. The filters have been experimentally tested and the results are compared with simulations. The miniaturization resulted in parasitic coupling between resonators and within each resonator that affected primarily the stopband and increased the bandwidth. The severity of the error depends on the design in particular, and was less sensitive when a groundplane was used under the inductances of the resonators. The best performance was reached for the quasi-lumped filter with central frequency of 4.45 GHz, quality factor of 40 and 50 dB stopband.

Superconductor Science and Technology•Apr 16, 2008•14 citations

Compact RSFQ microwave pulse generator based on an integrated RF module for controlling superconducting qubits

Yuxing He, Hongxiang Shen, Shiori Michibayashi +5 more

An on-chip superconducting microwave pulse generator (MPG), incorporating rapid single-flux-quantum (RSFQ) logic gates and passive radio frequency (RF) components, is an energy-efficient solution for controlling superconducting quantum bits (qubits). Traditional RSFQ MPG designs, however, suffer from a large footprint as multiple RF components (including impedance matching networks, filters, etc.) are separately implemented one after another. In this Letter, we propose a compact on-chip MPG by introducing an integrated RF module. Using a generalized filter synthesis technique, the integrated RF module combines the functionalities of impedance matching and bandpass filtering as a single inductor-capacitor (LC) lumped network. Plenty of circuit elements can, thus, be saved, and the resultant LC network is applicable to both real and complex terminal impedance cases. For validation, a superconducting MPG adopting a fourth-order, 5 GHz centered, 100 MHz bandwidth integrated RF module is designed and fabricated, whose correct operations are confirmed through both simulation and measurement. These results raise the availability of controlling large-scale quantum systems by low-power superconductor technology in the future.

Applied Physics Letters•Feb 7, 2022•14 citations

Study of mechanically tunable superconducting microwave filter using lumped elements

Shigeki Hontsu, S. Mine, Hiroaki Nishikawa +5 more

We propose a mechanically tunable superconducting microwave filter based on lumped elements composed of planar meander-line inductors (L) and inter-digital capacitors (C). As the first step, we have designed and evaluated a 3-pole Chebyshev bandpass filters with lumped elements using a circuit simulator. It is found that the center frequency, bandwidth and skirt rejection of the filter can be controlled by changing only the capacitance. The L and C elements values are estimated using an electromagnetic simulator. Furthermore, we have fabricated the inter-digital capacitor designed with the above procedure. We have evaluated change of the C values using mechanical tuning as a step toward a tunable superconducting microwave filter.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•14 citations

Miniaturization of superconducting passive filters for on-chip applications

Raihan Rafique, Peter Linnér, Bahar M. Motlagh +3 more

We present techniques to miniaturize superconducting ultra narrowband filters for on-chip applications. The filters are designed for 2 GHz, 5 GHz and 10 GHz operating frequencies. The expected bandwidths of the designed filters are 2-20 MHz. The designs are of 7 stages Chebyshev filters having maximum passband ripples of 0.5 dB. On-chip filters are particularly interesting as they are applicable for monolithic design with the RSFQ circuit aiming qubit applications. One of the designs is a quasi-lumped filter where the effective wave propagation constant has been increased by the addition of lumped components to the superconducting microstrip line (SMSL). Additionally, this design provides the optimum width of an SMSL without violating design rules. The other design consists of distributed and lumped components. The area of the filter is in the range of 1-2 square mm. We present the filter topologies and corresponding experimental results for the frequency response of these on-chip filters designed for Hypres 4.5 kA/cm2 fabrication process.

•Jan 1, 2007•1 citation
Abstract This paper presents a new class of sharp-selectivity low-temperature superconducting filter that incorporates lumped element resonant couplings. Dependent on a novel synthesis approach, the proposed filter exhibits great advantages such as: (1) a very simple in-line topology (without any cross coupling), (2) extremely compact size based on lumped inductor-capacitor (LC) elements, and (3) multiple transmission zeros (TZs) independently generated and controlled (via each resonant coupling). To facilitate the physical implementation, a group of lumped element circuit models are detailed, where series LC units are adopted for both the resonators and the resonant couplings. Considering an in-line topology here, the entire filter layout is then designed by cascading the lumped models one after another. For verification, a 5th-order bandpass filter centered at 5 GHz, with 500 MHz bandwidth and 3 TZs, is designed, simulated, and tested at cryogenic temperature (4.2 K). Moreover, preliminary simulations of the presented filter in series with an on-chip rapid single-flux-quantum microwave pulse generator are discussed for superconducting quantum applications.
This paper discusses a class of filters utilized in a low-power superconductor rapid single-flux-quantum (rapid SFQ, RSFQ) microwave pulse generator for controlling quantum bits (qubits). Here, the filter plays an important role to convert SFQ pulse trains (generated by RSFQ digital gates) and output a microwave control pulse. Characteristic of the output pulse can be adjusted by the in-band and roll-off performances of the filter, which is analyzed through numerical examples. Moreover, a novel in-line topology lumped network is proposed for the filter implementation, which can satisfy complex terminal cases at source (connecting an RSFQ digital block) and load (connecting a qubit). For the validation, we carry out a fourth-order bandpass filter using multilayer niobium (Nb) then-film technology, then incorporate it into an RSFQ control-pulse generator, and finally confirm correct functionality by both simulation and measurement.
Superconducting microelectronics (SME) technology has the potential of realizing very high speed digital receivers capable of performing direct digitization of radio frequency signals with very low power consumption. The SME receiver is implemented on a single chip using Niobium based low temperature superconductive (LTS) Josephson Junction (JJ) technology by HYPRES. Analogue RF filters are still required at the receiver front end and are key components of the overall superconductor digital receiver. SME receivers usually require two types of RF filters; a wideband bandpass filter and a bandstop filter (a notch filter). The notch filter is required to eliminate interference and unwanted signals in the passband. In this thesis, design of highly miniaturized lumped element wideband and bandstop filters is investigated and some challenges are addressed. The filters are fabricated by the HYPRES process and therefore can be integrated with the SME receiver on the same chip. \nIn a wideband filter, the coupling between the adjacent resonators is high. Achieving such a strong coupling is one of the challenges of designing wideband filters. The wideband filters realized with distributed elements usually suffer from very low spurious frequency. As the bandwidth of the filter becomes wider, the spurious peak of the second harmonic gets closer to the passband of the filter. In the first part of this work, the possibility of realizing lumped element superconducting bandpass filters (BPF) with a relative bandwidth of 80% is investigated. \nIn the second part of the thesis, design and realization of lumped element superconducting bandstop filters (BSF) is discussed. The challenge for designing a bandstop filter is providing a good match over a wide frequency range. So narrowband inverters cannot be used. Instead, usually λ/4 matched transmission lines provide 90° phase shift between the resonators of a notch filter. The possibility of replacing the long transmission line with other means or eliminating the inverters and using both shunt and series resonators are investigated. Having both series and shunt resonators introduces some new challenges that are addressed in the thesis and discussed thoroughly. \nA tunable notch resonator is presented. The tunability is provided by a superconducting MEMS varactor that is realized in our group by doing some post processing on the device fabricated by HYPRES. The tunability range of the device at cryogenic temperatures is investigated. A 3-pole tunable BSF is also designed that uses the same tunable resonators. The tunability of the filter is investigated through simulation.
In this paper we present methods for the miniaturization of superconducting filters. We consider two designs of seventh-order bandpass Chebyshev filters based on lumped elements and a novel quasi-lumped element resonator. In both designs the area of the filters, with a central frequency of 2–5 GHz, is less than 1.2 mm 2 . Such small filters can be readily integrated on a single board for multi-channel microwave control of superconducting qubits. The filters have been experimentally tested and the results are compared with simulations. The miniaturization resulted in parasitic coupling between resonators and within each resonator that affected primarily the stopband and increased the bandwidth. The severity of the error depends on the design in particular, and was less sensitive when a groundplane was used under the inductances of the resonators. The best performance was reached for the quasi-lumped filter with central frequency of 4.45 GHz, quality factor of 40 and 50 dB stopband.
An on-chip superconducting microwave pulse generator (MPG), incorporating rapid single-flux-quantum (RSFQ) logic gates and passive radio frequency (RF) components, is an energy-efficient solution for controlling superconducting quantum bits (qubits). Traditional RSFQ MPG designs, however, suffer from a large footprint as multiple RF components (including impedance matching networks, filters, etc.) are separately implemented one after another. In this Letter, we propose a compact on-chip MPG by introducing an integrated RF module. Using a generalized filter synthesis technique, the integrated RF module combines the functionalities of impedance matching and bandpass filtering as a single inductor-capacitor (LC) lumped network. Plenty of circuit elements can, thus, be saved, and the resultant LC network is applicable to both real and complex terminal impedance cases. For validation, a superconducting MPG adopting a fourth-order, 5 GHz centered, 100 MHz bandwidth integrated RF module is designed and fabricated, whose correct operations are confirmed through both simulation and measurement. These results raise the availability of controlling large-scale quantum systems by low-power superconductor technology in the future.
We propose a mechanically tunable superconducting microwave filter based on lumped elements composed of planar meander-line inductors (L) and inter-digital capacitors (C). As the first step, we have designed and evaluated a 3-pole Chebyshev bandpass filters with lumped elements using a circuit simulator. It is found that the center frequency, bandwidth and skirt rejection of the filter can be controlled by changing only the capacitance. The L and C elements values are estimated using an electromagnetic simulator. Furthermore, we have fabricated the inter-digital capacitor designed with the above procedure. We have evaluated change of the C values using mechanical tuning as a step toward a tunable superconducting microwave filter.
We present techniques to miniaturize superconducting ultra narrowband filters for on-chip applications. The filters are designed for 2 GHz, 5 GHz and 10 GHz operating frequencies. The expected bandwidths of the designed filters are 2-20 MHz. The designs are of 7 stages Chebyshev filters having maximum passband ripples of 0.5 dB. On-chip filters are particularly interesting as they are applicable for monolithic design with the RSFQ circuit aiming qubit applications. One of the designs is a quasi-lumped filter where the effective wave propagation constant has been increased by the addition of lumped components to the superconducting microstrip line (SMSL). Additionally, this design provides the optimum width of an SMSL without violating design rules. The other design consists of distributed and lumped components. The area of the filter is in the range of 1-2 square mm. We present the filter topologies and corresponding experimental results for the frequency response of these on-chip filters designed for Hypres 4.5 kA/cm2 fabrication process.