We present a versatile rf pulse control system that has been designed for multi-qubit quantum experiments. One instrument can be scaled to provide 32 channels of rf between 10 - 450 MHz. Synchronization can be achieved across multiple instruments. By using direct digital synthesis and custom control circuitry contained within a field-programmable gate array, sequences of transform-limited pulses can be produced. These have been used to carry out quantum gates that are able to meet fault-tolerant thresholds for single- and two-qubit gate fidelities, as published elsewhere. We have also extended the frequency to the gigahertz regime using additional mixers to address hyperfine transitions in atomic systems. The system uses an efficient memory management scheme and a low-latency communications protocol that allows pulse sequences to be updated in real-time. Together these can enable outcome-based algorithms such as quantum error correction to be executed. The system is fully programmable in C++, and other languages such as Python can be supported by the on-board CPU, offering a highly flexible platform for a wide variety of experimental systems, and has been proven in trapped-ion quantum information experiments.
We present a versatile rf pulse control system that has been designed for multi-qubit quantum experiments. One instrument can be scaled to provide 32 channels of rf between 10 - 450 MHz. Synchronization can be achieved across multiple instruments. By using direct digital synthesis and custom control circuitry contained within a field-programmable gate array, sequences of transform-limited pulses can be produced. These have been used to carry out quantum gates that are able to meet fault-tolerant thresholds for single- and two-qubit gate fidelities, as published elsewhere. We have also extended the frequency to the gigahertz regime using additional mixers to address hyperfine transitions in atomic systems. The system uses an efficient memory management scheme and a low-latency communications protocol that allows pulse sequences to be updated in real-time. Together these can enable outcome-based algorithms such as quantum error correction to be executed. The system is fully programmable in C++, and other languages such as Python can be supported by the on-board CPU, offering a highly flexible platform for a wide variety of experimental systems, and has been proven in trapped-ion quantum information experiments.
This thesis presents the development of a superconducting qubit control and readout system based on FPGA technology, with a focus on the design of a pulse sequencer and the integration of frequency-multiplexed control. The system leverages the Quantum Instrumentation Control Kit (QICK), an open-source Xilinx RFSoC-based platform capable of direct digital synthesis and acquisition of microwave signals up to 10 GHz. The QICK firmware was extended to support the simultaneous generation and readout of multiple frequency-multiplexed tones, enabling the control and measurement of several qubits coupled to a shared feedline. This approach optimizes the number of controllable qubits relative to the available ADC and DAC resources on the RFSoC 4x2 board. Furthermore, this work includes the development of Qubase, a Python-based pulse sequencer that allows users to easily define and execute complex sequences of control and measurement pulses through the QICK Python interface. The resulting architecture is both flexible and scalable, providing a foundation for efficient multi-qubit experiments and enabling advanced techniques such as quantum error correction and real-time feedback.
We introduce a Xilinx RF System-on-Chip (RFSoC)-based qubit controller (called the Quantum Instrumentation Control Kit, or QICK for short), which supports the direct synthesis of control pulses with carrier frequencies of up to 6 GHz. The QICK can control multiple qubits or other quantum devices. The QICK consists of a digital board hosting an RFSoC field-programmable gate array, custom firmware, and software and an optional companion custom-designed analog front-end board. We characterize the analog performance of the system as well as its digital latency, important for quantum error correction and feedback protocols. We benchmark the controller by performing standard characterizations of a transmon qubit. We achieve an average gate fidelity of Favg=99.93%. All of the schematics, firmware, and software are open-source.
In this paper we present a flexible, high-performance, integrated qubit control system using modular PXIe equipment. To manipulate qubits, a classical control system is required to generate and acquire a mix of baseband, radio frequency, and/or optical signals, with the specific mix different for each qubit technology. Typically, a quantum system requires many of these signals with a high degree of synchronization and phase coherence, and increasingly needs real-time data processing and on-the-fly sequencing capabilities for feedback experiments. The proposed system is scalable to hundreds of channels, all of them being phase coherent and fully time-synchronized.The system includes a programmable real-time sequencer for precise execution timing and decision making; and open FPGA capabilities for custom Digital Signal Processing (DSP) by hardware. Using the latter, we present FPGA IP to generate one-/two-qubit gates efficiently with the AWG, and to analyze high-frequency signals to measure the qubit states in real time on the digitizers. This IP features very low latencies for Quantum Error Correction (QEC) and Frequency Division Multiplexing (FDM) capabilities, among others.
Advanced quantum physics experiments place strict demands on control electronics, including phase-coherent multichannel RF/microwave generation, precise timing synchronization, low-latency response, and simultaneous support for wideband and near-DC signal processing. Existing control platforms often face trade-offs between channel count, integration level, and real-time performance, limiting scalability and experimental flexibility. In this work, we present a highly integrated real-time control system based on an XCZU49DR RFSoC. The platform integrates up to 16 RF DAC channels (9.85 GSa/s) and 16 RF ADC channels (2.5GSa/s) on a single chip, enabling synchronous multichannel signal generation and acquisition with deterministic timing. A custom RF front-end supports both broadband RF operation and low-frequency signal conditioning, while on-chip digital up/down conversion and programmable logic enable flexible waveform synthesis and real-time data processing. Performance characterization shows clean RF and microwave generation with spurious components suppressed below −59.0dBm at 200MHz and below −62.6dBm at 2.9GHz, while phase noise reaches −120.0dBc/Hz and −96.9dBc/Hz at 1kHz offset for 200MHz and 2.9GHz carriers, respectively, confirming low-noise and phase-coherent operation over a wide frequency range. The proposed platform provides a compact, scalable, and reconfigurable solution for quantum control and precision measurement. It is currently being applied to experiments involving NV centers and trapped ions, and can be readily adapted to other quantum systems, offering a practical foundation for next-generation
We describe a digital microwave platform called Presto, designed for measurement and control of multiple quantum bits (qubits) and based on the third-generation radio-frequency system on a chip. Presto uses direct digital synthesis to create signals up to 9 GHz on 16 synchronous output ports, while synchronously analyzing responses on 16 input ports. Presto has 16 DC-bias outputs, four inputs and four outputs for digital triggers or markers, and two continuous-wave outputs for synthesizing frequencies up to 15 GHz. Scaling to a large number of qubits is enabled through deterministic synchronization of multiple Presto units. A Python application programming interface configures a firmware for synthesis and analysis of pulses, coordinated by an event sequencer. The analysis integrates template matching (matched filtering) and low-latency (184-254 ns) feedback to enable a wide range of multi-qubit experiments. We demonstrate Presto's capabilities with experiments on a sample consisting of two superconducting qubits connected via a flux-tunable coupler. We show single-shot readout and active reset of a single qubit; randomized benchmarking of single-qubit gates showing 99.972% fidelity, limited by the coherence time of the qubit; and calibration of a two-qubit iSWAP gate.
We present a compact field-programmable gate array (FPGA) based pulse sequencer and radio-frequency (RF) generator suitable for experiments with cold trapped ions and atoms. The unit is capable of outputting a pulse sequence with at least 32 transistor-transistor logic (TTL) channels with a timing resolution of 40 ns and contains a built-in 100 MHz frequency counter for counting electrical pulses from a photo-multiplier tube. There are 16 independent direct-digital-synthesizers RF sources with fast (rise-time of ∼60 ns) amplitude switching and sub-mHz frequency tuning from 0 to 800 MHz.