Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1508.03131 · IEEE International Superconductive Electronics Conference (ISEC)

Design and Analysis on a Cryogenic Current Amplifier with a Superconducting Microwave Resonator

Yuma Okazaki, Nobu‐Hisa Kaneko

Published Jul 1, 2015• 0 citations
arXivHTMLPDF

Abstract

We propose a new type of cryogenic current amplifiers, in which low-frequency power spectrum of current can be measured through a measurement of microwave response of a superconducting resonant circuit shunted by a series array of Josephson junctions. From numerical analysis on the equivalent circuit, the numerical value of the input-referred current noise of the proposed amplifier is found to be two orders of magnitude lower than the noise floor measured with the conventional cryogenic current amplifiers based on high-electron-mobility transistors or superconducting quantum interference devices. Our proposal can open new avenues for investigating low-temperature solid-state devices that require lower noise and wider bandwidth power spectrum measurements of current.

DOI
10.1109/isec.2015.7383441

Related papers

A wideband cryogenic microwave low-noise amplifier

Boris I Ivanov, Dmitry I. Volkhin, Ilya L. Novikov +5 more

A broadband low-noise four-stage high-electron-mobility transistor amplifier was designed and characterized in a cryogen-free dilution refrigerator at the 3.8 K temperature stage. The obtained power dissipation of the amplifier is below 20 mW. In the frequency range from 6 to 12 GHz its gain exceeds 30 dB. The equivalent noise temperature of the amplifier is below 6 K for the presented frequency range. The amplifier is applicable for any type of cryogenic microwave measurements. As an example we demonstrate here the characterization of the superconducting X-mon qubit coupled to an on-chip coplanar waveguide resonator.

Beilstein Journal of Nanotechnology•Sep 30, 2020•8 citations

Low-noise and wide-bandwidth current readout at low temperatures using a superconducting-quantum-interference-device amplifier

Ngoc Thanh Mai Tran, Yuma Okazaki, Shuji Nakamura +2 more

Abstract We report on the development of a current amplifier for measuring small currents from mesoscopic electronic devices at low temperatures down to the milli-Kelvin range. In our setup, a superconducting quantum interference device (SQUID) located at the mixing chamber stage of the dilution refrigerator is used as the first-stage current amplifier, thereby improving the noise floor down to 8 × 10 −27 A 2 /Hz, which is one order of magnitude as low as those obtained by the conventional methods that utilize a semiconductor-based cryogenic current amplifier. We show the configuration of this setup and demonstrate the amplification of the current generated by a quantum point contact. This approach can open a new way to examine solid-state phenomena that are elusive owing to their small current.

Japanese Journal of Applied Physics•Mar 28, 2017•3 citations

Low-noise cryogenic microwave amplifier characterization with a calibrated noise source

M. Malnou, Trevyn F. Q. Larson, John D. Teufel +2 more

Parametric amplifiers have become a workhorse in superconducting quantum computing; however, research and development of these devices has been hampered by inconsistent and, sometimes, misleading noise performance characterization methodologies. The concepts behind noise characterization are deceptively simple, and there are many places where one can make mistakes, either in measurement or in interpretation and analysis. In this article, we cover the basics of noise performance characterization and the special problems it presents in parametric amplifiers with limited power handling capability. We illustrate the issues with three specific examples: a high-electron mobility transistor amplifier, a Josephson traveling-wave parametric amplifier, and a Josephson parametric amplifier. We emphasize the use of a 50-Ω shot noise tunnel junction (SNTJ) as a broadband noise source, demonstrating its utility for cryogenic amplifier amplifications. These practical examples highlight the role of loss as well as the additional parametric amplifier "idler" input mode.

arXiv:2312.14900•Review of Scientific Instruments•Mar 1, 2024•15 citations

DC-operated Josephson junction arrays as a cryogenic on-chip microwave measurement platform

Senne Vervoort, Lukas Nulens, Davi A. D. Chaves +8 more

Abstract Providing radio frequency (RF) signals to cryogenic circuits requires bulky and expensive cabling interfacing specialized RF electronics at room temperature. Superconducting-normal metal-superconducting Josephson junction arrays (JJAs) can change this paradigm by placing the RF source and detector on-chip. In this work, we demonstrate that DC-biased JJAs can emit signals in the C-band frequency spectrum and beyond, with a minimal linewidth of 106.5 ± 0.1 MHz and maximum power of 11.9 fW. We fabricate JJAs comprised of amorphous MoGe or NbTiN superconducting islands and metallic Au weak links. Temperature, magnetic field, applied current, and device design are explored to control the RF sources, while we identify important features that affect the ideal source behavior. Combined with the ability of these JJAs to detect microwave radiation, these sources allow us to propose a fully DC-operated cryogenic on-chip measurement platform that is an alternative to the high-frequency circuitry currently required for quantum applications.

arXiv:2412.17576•Communications Physics•Jul 12, 2025•2 citations

Design and development of a cryogenic semiconductor amplifier for interfacing RSFQ circuits at 4.2 K

S. Wünsch, E. Crocoll, M. Schubert +3 more

There is a great deal of interest in amplifiers with extremely high bandwidth, low noise and low power consumption which interface RSFQ circuits with commercial room temperature electronics or amplifying SFQ pulses. In this special application a hybrid amplifier should interface an RSFQ circuitry with a Josephson junction array quantizer chip (JA-Q) at 4.2 K. The input signal for the amplifier is generated by an RSFQ signal generator and the output signal fed-in to a Josephson array quantizer. A voltage gain of about 10 4 with a pattern frequency of 2 GHz for a good transfer of the SFQ pulses is required. Additionally, the JA-Q requires a high output current at low power consumption of the amplifier at the same time. Various hybrid amplifiers based on commercially available p-HEMT transistors in an embedded microwave design were designed and characterized. For the p-HEMT transistor characterization at cryogenic temperatures the biasing settings according to an optimum between voltage gain A V and low power consumption P V were determined. Thus a power consumption of P V = 2 mW and a voltage gain of about A V = 4 per stage were achieved. For a preamplifier and an amplifier concept a number of these stages were implemented in a microstrip and a coplanar transmission line design with a special matched interconnect taper towards the RSFQ components. Measurements of the amplifiers and the combination of the amplifiers and the JA-Q at 4.2 K showed their good performance without any disturbances of the quantized voltage steps.

Superconductor Science and Technology•Oct 18, 2007•7 citations

Input impedance and gain of a gigahertz amplifier using a dc superconducting quantum interference device in a quarter wave resonator

Lafe Spietz, K. D. Irwin, José Aumentado

Due to their superior noise performance, superconducting quantum interference devices (SQUIDs) are an attractive alternative to high electron mobility transistors for constructing ultra-low-noise microwave amplifiers for cryogenic use. We describe the use of a lumped element SQUID inductively coupled to a quarter wave resonator. The resonator acts as an impedance transformer and also makes it possible to accurately measure the input impedance and intrinsic microwave characteristics of the SQUID. We present a model for input impedance and gain, compare it to the measured scattering parameters, and describe how to use the model for the systematic design of low-noise microwave amplifiers with a wide range of performance characteristics.

arXiv:0806.2853•Applied Physics Letters•Aug 25, 2008•37 citations
We propose a new type of cryogenic current amplifiers, in which low-frequency power spectrum of current can be measured through a measurement of microwave response of a superconducting resonant circuit shunted by a series array of Josephson junctions. From numerical analysis on the equivalent circuit, the numerical value of the input-referred current noise of the proposed amplifier is found to be two orders of magnitude lower than the noise floor measured with the conventional cryogenic current amplifiers based on high-electron-mobility transistors or superconducting quantum interference devices. Our proposal can open new avenues for investigating low-temperature solid-state devices that require lower noise and wider bandwidth power spectrum measurements of current.
A broadband low-noise four-stage high-electron-mobility transistor amplifier was designed and characterized in a cryogen-free dilution refrigerator at the 3.8 K temperature stage. The obtained power dissipation of the amplifier is below 20 mW. In the frequency range from 6 to 12 GHz its gain exceeds 30 dB. The equivalent noise temperature of the amplifier is below 6 K for the presented frequency range. The amplifier is applicable for any type of cryogenic microwave measurements. As an example we demonstrate here the characterization of the superconducting X-mon qubit coupled to an on-chip coplanar waveguide resonator.
Abstract We report on the development of a current amplifier for measuring small currents from mesoscopic electronic devices at low temperatures down to the milli-Kelvin range. In our setup, a superconducting quantum interference device (SQUID) located at the mixing chamber stage of the dilution refrigerator is used as the first-stage current amplifier, thereby improving the noise floor down to 8 × 10 −27 A 2 /Hz, which is one order of magnitude as low as those obtained by the conventional methods that utilize a semiconductor-based cryogenic current amplifier. We show the configuration of this setup and demonstrate the amplification of the current generated by a quantum point contact. This approach can open a new way to examine solid-state phenomena that are elusive owing to their small current.
Parametric amplifiers have become a workhorse in superconducting quantum computing; however, research and development of these devices has been hampered by inconsistent and, sometimes, misleading noise performance characterization methodologies. The concepts behind noise characterization are deceptively simple, and there are many places where one can make mistakes, either in measurement or in interpretation and analysis. In this article, we cover the basics of noise performance characterization and the special problems it presents in parametric amplifiers with limited power handling capability. We illustrate the issues with three specific examples: a high-electron mobility transistor amplifier, a Josephson traveling-wave parametric amplifier, and a Josephson parametric amplifier. We emphasize the use of a 50-Ω shot noise tunnel junction (SNTJ) as a broadband noise source, demonstrating its utility for cryogenic amplifier amplifications. These practical examples highlight the role of loss as well as the additional parametric amplifier "idler" input mode.
Abstract Providing radio frequency (RF) signals to cryogenic circuits requires bulky and expensive cabling interfacing specialized RF electronics at room temperature. Superconducting-normal metal-superconducting Josephson junction arrays (JJAs) can change this paradigm by placing the RF source and detector on-chip. In this work, we demonstrate that DC-biased JJAs can emit signals in the C-band frequency spectrum and beyond, with a minimal linewidth of 106.5 ± 0.1 MHz and maximum power of 11.9 fW. We fabricate JJAs comprised of amorphous MoGe or NbTiN superconducting islands and metallic Au weak links. Temperature, magnetic field, applied current, and device design are explored to control the RF sources, while we identify important features that affect the ideal source behavior. Combined with the ability of these JJAs to detect microwave radiation, these sources allow us to propose a fully DC-operated cryogenic on-chip measurement platform that is an alternative to the high-frequency circuitry currently required for quantum applications.
There is a great deal of interest in amplifiers with extremely high bandwidth, low noise and low power consumption which interface RSFQ circuits with commercial room temperature electronics or amplifying SFQ pulses. In this special application a hybrid amplifier should interface an RSFQ circuitry with a Josephson junction array quantizer chip (JA-Q) at 4.2 K. The input signal for the amplifier is generated by an RSFQ signal generator and the output signal fed-in to a Josephson array quantizer. A voltage gain of about 10 4 with a pattern frequency of 2 GHz for a good transfer of the SFQ pulses is required. Additionally, the JA-Q requires a high output current at low power consumption of the amplifier at the same time. Various hybrid amplifiers based on commercially available p-HEMT transistors in an embedded microwave design were designed and characterized. For the p-HEMT transistor characterization at cryogenic temperatures the biasing settings according to an optimum between voltage gain A V and low power consumption P V were determined. Thus a power consumption of P V = 2 mW and a voltage gain of about A V = 4 per stage were achieved. For a preamplifier and an amplifier concept a number of these stages were implemented in a microstrip and a coplanar transmission line design with a special matched interconnect taper towards the RSFQ components. Measurements of the amplifiers and the combination of the amplifiers and the JA-Q at 4.2 K showed their good performance without any disturbances of the quantized voltage steps.
Due to their superior noise performance, superconducting quantum interference devices (SQUIDs) are an attractive alternative to high electron mobility transistors for constructing ultra-low-noise microwave amplifiers for cryogenic use. We describe the use of a lumped element SQUID inductively coupled to a quarter wave resonator. The resonator acts as an impedance transformer and also makes it possible to accurately measure the input impedance and intrinsic microwave characteristics of the SQUID. We present a model for input impedance and gain, compare it to the measured scattering parameters, and describe how to use the model for the systematic design of low-noise microwave amplifiers with a wide range of performance characteristics.