Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Precision Electromagnetic Measurements

Downscaling currents with the programmable quantum current generator

Sophie Djordjevic, Kamel Dougdag, Ralf Behr, Wilfrid Poirier

Published Sep 1, 2026• 0 citations
Publisher

Abstract

There is a challenge in downscaling quantized currents generated by the programmable quantum current generator (PQCG) to bridge the gap with other quantum sources and enable comparison of standards. Achieving this objective requires both simplifying and optimizing the settings of the full experiment, which involves two programmable Josepshon voltage standards (PJVS), two quantum Hall resistance standards and one cryogenic current comparator. Here, we describe an upgraded experiment involving a new cryogenic setup based on a pulse-tube refrigerator used to cool down the two PJVS. We demonstrate generation of quantized currents in the range from 4307 nA down to 359 nA with relative uncertainties ranging from 1 part to 9 parts in 108, respectively. The calibration of the ultra low current source from Magnicon using the PQCG is then demonstrated in same current ranges.

DOI
10.1109/cpem68396.2026.11756459

Related papers

A primary quantum current standard based on the Josephson and the quantum Hall effects

Sophie Djordjevic, Ralf Behr, W. Poirier

The new definition of the ampere calls for a quantum current standard able to deliver a flow of elementary charges, e, controlled with a relative uncertainty of 10−8. Despite many efforts, nanodevices handling electrons one by one have never demonstrated such an accuracy for a net flow. The alternative route based on applying Ohm’s law to the Josephson voltage and quantum Hall standards recently reached the target uncertainty in the milliampere range, but this was at the expense of the application of error corrections. Here, we present a new programmable quantum current generator, which combines both quantum standards and a superconducting cryogenic amplifier in a quantum electrical circuit enabling the current scaling without errors. Thanks to a full quantum instrumentation, we demonstrate the accuracy of the generated currents, in the microampere range, at quantized values, ±(n/p)efJ, with relative uncertainties less than 10−8, where n and p are integer control parameters and fJ is the Josephson frequency. This experiment sets the basis of a universal quantum realization of the electrical units, for example able of improving high-value resistance measurements and bridging the gap with other quantum current sources. Realizing the ampere, the unit of electrical current, involves controlling a flow of elementary charges with high accuracy. Here, the authors present the generation of sizeable currents at quantized values with relative uncertainties below 10−8.

arXiv:2407.12562•Nature Communications•Feb 10, 2025•19 citations

Towards a programmable quantum current generator

J. Brun-Picard, D. Leprat, F. Schopfer +2 more

We report on the development of a programmable quantum current generator (PQCG) based on quantum voltage and resistance standards. First measurements with a digital amperemeter in the 100 μA range demonstrate the linearity of the generated current as a function of the theoretical current, linked to the electron charge, with a relative uncertainty of 2.7 × 10-7(k = 1). To overcome the detector limits and validate the PQCG as a practical realization of the ampere in the new SI, accurate quantization measurements with a target combined uncertainty of a few parts in 108are in progress.

Conference on Precision Electromagnetic Measurements•Jul 1, 2016•0 citations

Next generation Programmable Quantum Current Generator

Sophie Djordjevic, Ralf Behr, W. Poirier

This paper describes the latest improvements of the programmable quantum current generator (PQCG), which allow to get rid of the former 10−7relative corrections due to the resistance of the cable and extend the realization of the ampere over a wider current range, down to the µA range. Here we report on the first results of accuracy tests at 46 µA with a measurement uncertainty of one part in 108.

Conference on Precision Electromagnetic Measurements•Jul 8, 2024•0 citations

Practical Quantum Realization of the Ampere from the Elementary Charge

J. Brun-Picard, S. Djordjevic, D. Leprat +2 more

One major change of the future revision of the International System of Units is a new definition of the ampere based on the elementary charge e. Replacing the former definition based on Ampère's force law will allow one to fully benefit from quantum physics to realize the ampere.However, a quantum realization of the ampere from e, accurate to within 10 -8 in relative value and fulfilling traceability needs, is still missing despite the many efforts made for the development of single-electron tunneling devices.Starting again with Ohm's law, applied here in a quantum circuit combining the quantum Hall resistance and Josephson voltage standards with a superconducting cryogenic amplifier, we report on a practical and universal programmable quantum current generator.We demonstrate that currents generated in the milliampere range are accurately quantized in terms of ef J (f J is the Josephson frequency) with measurement uncertainty of 10 -8 .This new quantum current source, which is able to deliver such accurate currents down to the microampere range, can greatly improve the current measurement traceability, as demonstrated with the calibrations of digital ammeters.In addition, it opens the way to further developments in metrology and in fundamental physics, such as a quantum multimeter or new accurate comparisons to single-electron pumps.

arXiv:1606.03964•Physical Review X•Dec 12, 2016•52 citations

Josephson-based quantum voltage standards – an ongoing success story

Ralf Behr, Stephan Bauer, Marco Kraus +2 more

The past few decades have witnessed great progress being made from the first voltage standards based on arrays of Josephson junctions. Continuous improvements in the fabrication process have increased the quality and “user-friendliness” of these superconducting circuits. Combined with the improvements in measuring electronics, the range of applications of Josephson-based measurements with unmatched precision has extended from DC into AC voltage metrology for signal frequencies up to 500 kHz. In this poster we will present several Josephson-based measurement systems developed for metrology applications. Two versions of quantum AC standards will be used as Josephson references: Programmable Josephson Voltage Standards (PJVS), which are based on serial arrays with up to 300,000 Josephson junctions, and pulse-driven arrays with more than 50,000 junctions, typically referred to as Josephson Arbitrary Waveform Synthesizers (JAWS). PJVS can reach amplitudes of up to 80 V, while pulse-driven arrays can reach up to 1 V or even 4 V. The advantage of pulse-driven Josephson voltage standards is that they are ideally suited as quantum-based voltage synthesizers for arbitrary waveforms or sine waves with high spectral purity. Therefore, they can be used directly to characterize or calibrate ADCs. In addition, JAWS are particularly useful in Josephson impedance bridges, which perform automated impedance calibrations at the 10-9 uncertainty level over a wide frequency range from 50 Hz to 80 kHz in a single bridge. We will further show how PJVS are used in commercial quantum voltmeters for DC and AC voltages and are typically used as quantum voltage references in measurement systems. Using differential sampling based on PJVS, uncertainties at the level of a few parts in 108 for frequencies up to the kHz range can be achieved. Such quantum-based AC voltage calibrations are at least 30 times faster than conventional AC-DC transfer and offer even better uncertainties. This idea has been quickly adopted by many National Metrology Institutes to establish such systems for AC voltage calibrations. As an example, the BIPM will now start worldwide onsite comparisons to ensure the uniformity of the new method which we introduced in 2006. But developments continue. Recently, a sub-sampling technique was used to extend the frequency range of the AC quantum voltmeter to up to 100 kHz with uncertainties below 5 parts in 106. In addition, a novel method, also for differential sampling, enables the measurement of arbitrary waveforms and the calibration of specific tones. Our poster will provide an overview of these Josephson-based metrological applications and present the latest developments from this fast-developing area.

•Jan 1, 2025•0 citations

A New Era for the Ampere

Mark W. Keller, José Aumentado

One major change of the future revision of the International System of Units is a new definition of the ampere based on the elementary charge e. Replacing the former definition based on Ampère's force law will allow one to fully benefit from quantum physics to realize the ampere.However, a quantum realization of the ampere from e, accurate to within 10 -8 in relative value and fulfilling traceability needs, is still missing despite the many efforts made for the development of single-electron tunneling devices.Starting again with Ohm's law, applied here in a quantum circuit combining the quantum Hall resistance and Josephson voltage standards with a superconducting cryogenic amplifier, we report on a practical and universal programmable quantum current generator.We demonstrate that currents generated in the milliampere range are accurately quantized in terms of ef J (f J is the Josephson frequency) with measurement uncertainty of 10 -8 .This new quantum current source, which is able to deliver such accurate currents down to the microampere range, can greatly improve the current measurement traceability, as demonstrated with the calibrations of digital ammeters.In addition, it opens the way to further developments in metrology and in fundamental physics, such as a quantum multimeter or new accurate comparisons to single-electron pumps.

Physics•Dec 12, 2016•4 citations
There is a challenge in downscaling quantized currents generated by the programmable quantum current generator (PQCG) to bridge the gap with other quantum sources and enable comparison of standards. Achieving this objective requires both simplifying and optimizing the settings of the full experiment, which involves two programmable Josepshon voltage standards (PJVS), two quantum Hall resistance standards and one cryogenic current comparator. Here, we describe an upgraded experiment involving a new cryogenic setup based on a pulse-tube refrigerator used to cool down the two PJVS. We demonstrate generation of quantized currents in the range from 4307 nA down to 359 nA with relative uncertainties ranging from 1 part to 9 parts in 108, respectively. The calibration of the ultra low current source from Magnicon using the PQCG is then demonstrated in same current ranges.
The new definition of the ampere calls for a quantum current standard able to deliver a flow of elementary charges, e, controlled with a relative uncertainty of 10−8. Despite many efforts, nanodevices handling electrons one by one have never demonstrated such an accuracy for a net flow. The alternative route based on applying Ohm’s law to the Josephson voltage and quantum Hall standards recently reached the target uncertainty in the milliampere range, but this was at the expense of the application of error corrections. Here, we present a new programmable quantum current generator, which combines both quantum standards and a superconducting cryogenic amplifier in a quantum electrical circuit enabling the current scaling without errors. Thanks to a full quantum instrumentation, we demonstrate the accuracy of the generated currents, in the microampere range, at quantized values, ±(n/p)efJ, with relative uncertainties less than 10−8, where n and p are integer control parameters and fJ is the Josephson frequency. This experiment sets the basis of a universal quantum realization of the electrical units, for example able of improving high-value resistance measurements and bridging the gap with other quantum current sources. Realizing the ampere, the unit of electrical current, involves controlling a flow of elementary charges with high accuracy. Here, the authors present the generation of sizeable currents at quantized values with relative uncertainties below 10−8.
We report on the development of a programmable quantum current generator (PQCG) based on quantum voltage and resistance standards. First measurements with a digital amperemeter in the 100 μA range demonstrate the linearity of the generated current as a function of the theoretical current, linked to the electron charge, with a relative uncertainty of 2.7 × 10-7(k = 1). To overcome the detector limits and validate the PQCG as a practical realization of the ampere in the new SI, accurate quantization measurements with a target combined uncertainty of a few parts in 108are in progress.
One major change of the future revision of the International System of Units is a new definition of the ampere based on the elementary charge e. Replacing the former definition based on Ampère's force law will allow one to fully benefit from quantum physics to realize the ampere.However, a quantum realization of the ampere from e, accurate to within 10 -8 in relative value and fulfilling traceability needs, is still missing despite the many efforts made for the development of single-electron tunneling devices.Starting again with Ohm's law, applied here in a quantum circuit combining the quantum Hall resistance and Josephson voltage standards with a superconducting cryogenic amplifier, we report on a practical and universal programmable quantum current generator.We demonstrate that currents generated in the milliampere range are accurately quantized in terms of ef J (f J is the Josephson frequency) with measurement uncertainty of 10 -8 .This new quantum current source, which is able to deliver such accurate currents down to the microampere range, can greatly improve the current measurement traceability, as demonstrated with the calibrations of digital ammeters.In addition, it opens the way to further developments in metrology and in fundamental physics, such as a quantum multimeter or new accurate comparisons to single-electron pumps.
The past few decades have witnessed great progress being made from the first voltage standards based on arrays of Josephson junctions. Continuous improvements in the fabrication process have increased the quality and “user-friendliness” of these superconducting circuits. Combined with the improvements in measuring electronics, the range of applications of Josephson-based measurements with unmatched precision has extended from DC into AC voltage metrology for signal frequencies up to 500 kHz. In this poster we will present several Josephson-based measurement systems developed for metrology applications. Two versions of quantum AC standards will be used as Josephson references: Programmable Josephson Voltage Standards (PJVS), which are based on serial arrays with up to 300,000 Josephson junctions, and pulse-driven arrays with more than 50,000 junctions, typically referred to as Josephson Arbitrary Waveform Synthesizers (JAWS). PJVS can reach amplitudes of up to 80 V, while pulse-driven arrays can reach up to 1 V or even 4 V. The advantage of pulse-driven Josephson voltage standards is that they are ideally suited as quantum-based voltage synthesizers for arbitrary waveforms or sine waves with high spectral purity. Therefore, they can be used directly to characterize or calibrate ADCs. In addition, JAWS are particularly useful in Josephson impedance bridges, which perform automated impedance calibrations at the 10-9 uncertainty level over a wide frequency range from 50 Hz to 80 kHz in a single bridge. We will further show how PJVS are used in commercial quantum voltmeters for DC and AC voltages and are typically used as quantum voltage references in measurement systems. Using differential sampling based on PJVS, uncertainties at the level of a few parts in 108 for frequencies up to the kHz range can be achieved. Such quantum-based AC voltage calibrations are at least 30 times faster than conventional AC-DC transfer and offer even better uncertainties. This idea has been quickly adopted by many National Metrology Institutes to establish such systems for AC voltage calibrations. As an example, the BIPM will now start worldwide onsite comparisons to ensure the uniformity of the new method which we introduced in 2006. But developments continue. Recently, a sub-sampling technique was used to extend the frequency range of the AC quantum voltmeter to up to 100 kHz with uncertainties below 5 parts in 106. In addition, a novel method, also for differential sampling, enables the measurement of arbitrary waveforms and the calibration of specific tones. Our poster will provide an overview of these Josephson-based metrological applications and present the latest developments from this fast-developing area.
One major change of the future revision of the International System of Units is a new definition of the ampere based on the elementary charge e. Replacing the former definition based on Ampère's force law will allow one to fully benefit from quantum physics to realize the ampere.However, a quantum realization of the ampere from e, accurate to within 10 -8 in relative value and fulfilling traceability needs, is still missing despite the many efforts made for the development of single-electron tunneling devices.Starting again with Ohm's law, applied here in a quantum circuit combining the quantum Hall resistance and Josephson voltage standards with a superconducting cryogenic amplifier, we report on a practical and universal programmable quantum current generator.We demonstrate that currents generated in the milliampere range are accurately quantized in terms of ef J (f J is the Josephson frequency) with measurement uncertainty of 10 -8 .This new quantum current source, which is able to deliver such accurate currents down to the microampere range, can greatly improve the current measurement traceability, as demonstrated with the calibrations of digital ammeters.In addition, it opens the way to further developments in metrology and in fundamental physics, such as a quantum multimeter or new accurate comparisons to single-electron pumps.