This paper presents a polynomial I/Q envelope generator for superconducting qubit control that requires no waveform lookup table. The architecture computes DRAG-like in-phase and quadrature envelopes from a compact support polynomial, without storing pulse samples. Programmable parameters control pulse duration, in-phase amplitude, and quadrature strength. A 16-bit VHDL implementation on a Zynq UltraScale+ FPGA meets a 500 MHz timing constraint after placement and routing, using 57 LUTs, 20 flip-flops, and 5 DSP blocks. The generated pulse family is compared with Gaussian-DRAG through normalized spectral analysis and closed-system simulations of a three-level transmon. These results characterize the hardware cost and simulated quantum control performance of the proposed generator.
This paper presents a polynomial I/Q envelope generator for superconducting qubit control that requires no waveform lookup table. The architecture computes DRAG-like in-phase and quadrature envelopes from a compact support polynomial, without storing pulse samples. Programmable parameters control pulse duration, in-phase amplitude, and quadrature strength. A 16-bit VHDL implementation on a Zynq UltraScale+ FPGA meets a 500 MHz timing constraint after placement and routing, using 57 LUTs, 20 flip-flops, and 5 DSP blocks. The generated pulse family is compared with Gaussian-DRAG through normalized spectral analysis and closed-system simulations of a three-level transmon. These results characterize the hardware cost and simulated quantum control performance of the proposed generator.
Accurate microwave waveform delivery is a critical requirement for superconducting-qubit control.Although pulse-shaping methods are often discussed from a quantumcontrol perspective, their practical performance also depends on electrical-engineering constraints such as baseband-equivalent control-envelope bandwidth, waveform distortion, carrier detuning, and IQ quadrature accuracy.This paper presents a compact RF-control-chain-aware simulation study of microwave pulse shaping for a nominal single-qubit Xπ operation in a three-level superconducting-qubit load model.Square, Gaussian, and derivative-removal-by-adiabatic-gate (DRAG)-style pulse envelopes are compared.As a simplified approximation of bandwidth-limited waveform delivery, a causal low-pass transfer function is applied to padded in-phase and quadrature pulse envelopes before the qubit-load simulation.The results show that shaped pulses reduce leakage relative to abrupt rectangular excitation, but finite bandwidth modifies the delivered waveform and changes the leakage response in a pulse-shape-dependent manner.For the simulated 20 ns case, low-bandwidth filtering smooths and temporally extends the delivered envelopes, while sufficiently large bandwidths approach the ideal-waveform response.The study highlights the importance of joint pulse-shape design, envelope bandwidth budgeting, detuning control, and calibration in microwave control systems for scalable quantum hardware.
Superconducting qubits are the promising candidate to realize large-scale quantum computing systems. Well-known quantum algorithms, such as Shor's algorithm, require at least105to106qubits to execute. Accordingly, classical systems for controlling superconducting qubits must also be scalable. One critical scalability challenge lies in the circuit cost of an RF pulse generator used to implement quantum gate operations. This poster proposes a cost-effective architecture for an RF pulse generator tailored to superconducting qubits. Most existing works use arbitrary waveform generators (AWGs) that require both a high-bandwidth memory (HBM) and a high-performance digital-analog converter (DAC) to achieve the highest gate fidelity with an optimized RF pulse waveform. The proposed pulse generator architecture significantly simplifies both the generator circuit and the waveform of the RF pulse to cost-aware square pulses. This architecture eliminates the requirement for power- and cost-intensive AWG, which is a major obstacle in realizing scalable quantum computers. Additionally, this poster demonstrates that our architecture can mitigate the error source associated with simplified RF pulses. Quantum dynamics simulation of transmon qubits, wherein the state of the system evolves with time, demonstrates that our pulse generator can achieve practically the same fidelity of gate operations for single and multiple qubits as ideal RF pulses while substantially reducing the sampling rate of DACs and the bandwidth of memories.
This paper reports the development of a low-latency arbitrary waveform generator (AWG), which is suitable for the control and measurement of superconducting quantum computers. It can generate qubit control signals and measurement signals in real time. Compared with commercial AWG, our AWG has less latency and higher analog bandwidth. Compressing latency can reduce system feedback time, and higher analog bandwidth improves the system's integration by mounting more qubits on the readout line. The AWG integrates four high-speed digital-to-analog converters (DACs), phase-locked loop (PLL) circuits, field-programmable gate arrays (FPGAs), and related circuits into a standard PXI 3U board. The waveform generator module, communication interface module, clock module, and configuration module are realized utilizing the FPGA. The FPGA-based hardware architecture enables AWG to be flexibly configured to meet the various needs of quantum experiments. The four-channel AWG has a 2-GSa/s sampling rate, a 14-bit resolution, and 500 MHz bandwidth. The jitter in the AWG output waveform is approximately 3 ps; the latency of the AWG (the time from the feedback trigger received until a feedback pulse is generated) is approximately 55 ns. These designs form the basis of realizing control system for large-scale quantum computing.
Signal generators for qubit control and measure-ments play a key role in quantum computers in terms of latency and scalability. Typically, the control pulses are generated by arbitrary waveform generators (AWGs) via preloaded lookup tables. However, this method lacks the flexibility to adjust phase and frequency in complicated programs, such as variational quantum eigensolvers (VAE) or pulse shape optimization al-gorithms. Therefore, we propose a quantum control system composed of a quantum control processor (QCP) and a run-time waveform-configurable signal generator in this work. For the signal generator, we developed a parallelized direct digital synthesis (DDS) structure to adaptively generate waveforms without requiring the entire waveform to be preloaded. The QCP, based on HiSEP-Q, is optimized with a deeper pipelined architecture to increase frequency and match the high bandwidth of signal generators. Additionally, we introduce a synchronization architecture in the QCP to manage uneven delays among different generation threads. Validated on the ZCU216 platform, our system achieves flexible signal generation with an average latency of 20 ns and reduces memory usage by more than 50%.
Scaling superconducting quantum computers toward thousands of control channels remains a difficult hardware problem. This requires reducing room-temperature-to-cryogenic interconnects and 4 K power while retaining channel-specific programmability. We develop a hybrid photonic/CMOS control architecture in which optical fibers distribute shared Gaussian and derivative pulse templates, while local cryogenic CMOS circuits provide event-rate amplitude programming, pulse blocking, hold-duration control, photodetection, and microwave upconversion. The architecture supports template-based XY/DRAG control and smooth-edged flat-top envelopes for two-qubit control through separate local signal paths. Compared with full-waveform Cryo-CMOS, it moves high-speed sampled-waveform generation out of each cryogenic channel. Compared with per-channel photonic waveform delivery, it retains a programmable endpoint after optical distribution for applying updated channel coefficients and control states. We evaluate the architecture using post-layout circuit simulations, optical and interconnect models, and system-level power scaling under a common 4 K output boundary. The modeled downlink power is below 1 mW per qubit-control channel at the thousand-channel scale, substantially below the normalized full-waveform Cryo-CMOS result and in the same range as the strict 50-ohm direct-detection WDM reference. Simulated I- and Q-path outputs are propagated through a five-level transmon model, while the simulated sample-and-hold output is evaluated in a coupled-transmon model. The tested single-qubit cases remain below the 10^-3 worst-state error reference, and the representative two-qubit result remains near the same scale after model-level calibration. These results support low-power photonic delivery with limited in-fridge programmability for template-compatible superconducting-qubit control.
High-fidelity control of superconducting qubits requires carefully shaped microwave pulses to avoid several different kinds of error at once. This article is a pedagogical bridging text aimed at upper-level undergraduate and early graduate students who have completed an introductory quantum mechanics course and a first course in quantum computing or quantum information, but who have not yet encountered the physical implementation of qubit gates. We integrate physical intuition for pulse design, analytical gate-level descriptions, and practical hardware considerations into a single, derivation-driven narrative, with explicit learning objectives. We begin with simple pulse envelopes and their spectral properties, showing how finite bandwidth produces leakage outside the computational subspace. This motivates the derivative removal by adiabatic gate (DRAG) technique, which we derive explicitly using the Magnus expansion, obtaining a clear, order-by-order account of which physical error channel appears at which order and why DRAG's cancellation is necessarily incomplete. We discuss the practical hardware realities of control pulse generation, focusing on arbitrary waveform generators (AWG), local oscillators (LO), and IQ mixing. Finally, we extend the discussion to two-qubit operation via the cross-resonance gate, and interpret how driving the control qubit at the target qubit's transition frequency necessarily produces several unwanted interaction terms alongside the desired one, and how successive generations of pulse-engineering strategies have been designed to suppress them.