Development and calibration of room-temperature microwave control electronics for superconducting qubits is gated by the cooldown time and limited availability of dilution-refrigerator-mounted qubits used as test loads. We present Q-EMU, a passive PCB-level distributed microwave circuit that emulates the room-temperature signature of a transmon coupled to a readout resonator. Q-EMU is a distributed version of the standard cQED equivalent circuit that uses an SPDT switch in place of the Josephson element and a shunt hyperabrupt varactor for both continuous frequency tuning and an emulated AC Stark shift via $C(V)$ nonlinearity, so the drive port load-tests the transmit chain while the readout feedline pair load-tests the receive chain. Large-signal simulations on a Rogers RO4350B-class PCB show a principal coupled mode at 6.58 GHz (loaded $Q \approx 108, \kappa / 2 \pi \approx \mathbf{6 1 ~ M H z}$), a state-dependent dispersive shift $\chi_{\text {eff }} / 2 \pi \approx \mathbf{2 8 ~ M H z}$, continuous bias tunability of the qubit-resonator frequency over ~250 MHz at essentially constant linewidth, and a power-dependent shift fitting $f_{q}(P)=f_{0}-A P_{\text{lin}}$ with $A \approx \mathbf{6 3 ~ k H z} / \mathrm{mW}$ (58 MHz total span over 0-30 dBm). The current baseline operates in the borderline-dispersive regime; reducing $C_{g}$ by $\sim \mathbf{5} \times$ in a follow-up revision would bring $\chi / 2 \pi$ into the $\sim \mathbf{1} \mathrm{MHz}$ regime typical of real transmons while reducing the power-dependent shift. The design scales naturally to mm-wave frequencies for emerging K-band superconducting qubits.
Development and calibration of room-temperature microwave control electronics for superconducting qubits is gated by the cooldown time and limited availability of dilution-refrigerator-mounted qubits used as test loads. We present Q-EMU, a passive PCB-level distributed microwave circuit that emulates the room-temperature signature of a transmon coupled to a readout resonator. Q-EMU is a distributed version of the standard cQED equivalent circuit that uses an SPDT switch in place of the Josephson element and a shunt hyperabrupt varactor for both continuous frequency tuning and an emulated AC Stark shift via C(V) nonlinearity, so the drive port load-tests the transmit chain while the readout feedline pair load-tests the receive chain. Large-signal simulations on a Rogers RO4350B-class PCB show a principal coupled mode at 6.58 GHz (loaded Q≈108,κ/2π≈61MHz), a state-dependent dispersive shift χeff /2π≈28MHz, continuous bias tunability of the qubit-resonator frequency over ~250 MHz at essentially constant linewidth, and a power-dependent shift fitting fq(P)=f0−APlin with A≈63kHz/mW (58 MHz total span over 0-30 dBm). The current baseline operates in the borderline-dispersive regime; reducing Cg by ∼5× in a follow-up revision would bring χ/2π into the ∼1MHz regime typical of real transmons while reducing the power-dependent shift. The design scales naturally to mm-wave frequencies for emerging K-band superconducting qubits.
This thesis presents circuit quantum electrodynamic (cQED) experiments done with artificial atoms coupled to a high quality factor superconducting microwave resonator. This work discusses the theoretical framework, design, fabrication, implementation and characterization of a multi-qubit system using superconducting persistent current qubits, often referred as flux qubits. \n \nWe developed a new type of cryogenic aid for fast turnaround microwave experiments. The minimum turnaround time to perform microwave experiments in dilution refrigerators is typically a few days, as required by cooling down and warming up the entire refrigerator. The cryogenic microwave payload and wiring needed for each qubit and resonator add a significant heat load to \nthe system which typically only has a few µW s of cooling power at millikelvin temperatures. We present a new experimental approach we developed in which a suitable sample holder is attached to a cold-insertable probe and brought in contact with transmission lines permanently mounted inside the cryostat. The total turnaround time is reduced to 8 hours if the target temperature is 80 mK. This new measurement method increased our ability to successfully identify good devices with fast design-characterization iterations, while allowing months-long measurements at 30 mK. \n \nOur device architecture uses several qubits, each of which is controlled via on-chip fast flux bias lines. Readout of the qubit’s quantum state is performed by homodyne detection of the resonator field at large driving power. We observe long coherence times at the optimal bias point of the flux qubits and present decoherence measurements around this optimal point, where the \nflux qubits couple mostly to magnetic flux noise. Dynamical decoupling techniques employing fast microwave pulses are used to protect the qubit’s coherence and allow calculating the magnetic flux noise power spectral density of the qubit’s environment. Photon-mediated interaction between distant qubits in the resonator allows the implementation of a two-qubit controlled-NOT gate \nusing the selective darkening technique. \n \nThis multi-qubit superconducting design is an interesting platform to study the decoherence properties of flux qubits, the properties of strong interaction of electromagnetic radiation with macroscopic quantum systems. These results demonstrate the potential of cQED as a platform for fundamental investigations of decoherence and quantum dynamics of flux qubits.
Metamaterial resonant structures made from arrays of superconducting lumped-circuit elements can exhibit microwave-mode spectra with left-handed dispersion for the standing-wave resonances, resulting in a high density of modes in the same frequency range where superconducting qubits are typically operated, as well as a bandgap at lower frequencies that extends down to dc. Using this regime for multimode circuit quantum electrodynamics, we perform a series of measurements of such a superconducting metamaterial resonator coupled to a flux-tunable transmon qubit. Through microwave measurements of the metamaterial, we observe the coupling of the qubit to each of the modes that it passes through. Using a separate readout resonator, we probe the qubit dispersively and characterize the qubit energy relaxation as a function of frequency, which is strongly affected by the Purcell effect in the presence of the dense mode spectrum. Additionally, we investigate the ac Stark shift of the qubit as the photon number in the various metamaterial modes is varied. Through numerical simulations, we explore designs based on this scheme with enhanced coupling so that the coupling energy between the qubit and the metamaterial modes can exceed the intermode spacing in future devices with achievable circuit parameters. The ability to tailor the dense mode spectrum through the choice of circuit parameters and manipulate the photonic state of the metamaterial through interactions with qubits makes this a promising platform for analog quantum simulation with microwave photons and quantum memories.
Superconducting quantum circuits have emerged as a leading platform for building large-scale quantum computers, owing to their ability to engineer strong, highly tunable interactions. However, achieving high-fidelity quantum operations requires overcoming the fundamental isolation-andcontrol challenge: qubits must be well-isolated from their electromagnetic environment to maintain long coherence times, yet they require strong external coupling for fast control, readout, and initialization. In current architectures, this trade-off often demands complex auxiliary circuitry that can introduce additional noise and thermal loads. This thesis presents novel circuit designs and control techniques to address the isolation-and-control challenge in superconducting transmon qubits. First, we introduce integrated on-chip filters, in particular, 𝜆/4 and 𝜆/2 transmission line filters that exhibit a stopband at the qubit frequency. This design protects the qubit from Purcell decay, yielding up to a 200-fold improvement in the energy relaxation time 𝑇1 at the stopband. To achieve fast single-qubit gates despite this isolation, we employ subharmonic driving, demonstrating sub-ten-nanosecond control and Rabi oscillations with a 12-ns pulse duration while significantly reducing the cryogenic thermal load. Building upon these static filters, we propose and experimentally demonstrate the quantum dial, a dynamically tunable band-stop filter consisting of a series array of direct-current superconducting quantum interference devices. The quantum dial enables on-demand tuning of the qubit–environment coupling, including a reduction of 𝑇1 from over 150 μs to roughly 200 ns, while introducing minimal ac Stark shifts. We demonstrate its versatility by dialing between three operational regimes: an idle state with 99.99% fidelity, a control state enabling 99.9% fidelity for 40-ns single-qubit gates at −110 dBm, and a strongly coupled state for unconditional, state-independent qubit reset. Furthermore, the quantum dial enables qubit thermometry close to the quantum-Fisherinformation bound, with a noise-equivalent temperature down to 0.6 mK/√Hz at 60 mK. Alongside the development of these dedicated control architectures, this thesis contributes to the broader framework of circuit quantum electrodynamics by advancing specific microwave engineering and characterization techniques. In particular, we explore the miniaturization of circuit footprints through the realization of compact sub-gigahertz inductor-capacitor resonators. Additionally, we contribute to the optimization of unconditional qubit reset using a single-junction quantum-circuit refrigerator, and to the advanced characterization of microwave fields via computed tomography of propagating microwave photons. In summary, these results demonstrate fixed and tunable drive-line filters that suppress idle-state radiative decay while preserving selected control, reset, and thermometry operations. By replacing static coupling compromises with temporally programmable environments, these architectures offer a promising route to reducing noise, mitigating crosstalk, and accelerating error-correction cycles in future superconducting quantum processors.
Circuit quantum electrodynamics (cQED), exemplified by a coupled system of a superconducting qubit and a microwave cavity, is a powerful framework for the quantum control and measurement of macroscopic quantum states in solid-state circuits. Quantum circuits based on superconducting qubits have emerged as one of the leading platforms in the pursuit of fault-tolerant quantum computing. Despite significant progress in extending qubit lifetimes, refining experimental protocols, and scaling up quantum processors, errors arising from the control and measurement of superconducting qubits continue to hinder the realization of a universal quantum computer. To investigate the error mechanisms for state-of-the-art qubits, we realize long-lived superconducting transmon qubits that exhibit fluctuating lifetimes, with an average of 0.2 ms and a maximum exceeding 0.4 ms. We then investigate their dominant error mechanism. By introducing novel time-resolved error measurements that are synchronized with the operation of the pulse tube cooler in a dilution refrigerator, we find that mechanical vibrations from the pulse tube induce nonequilibrium dynamics in highly coherent qubits, leading to their correlated bit-flip errors. Our findings not only deepen our understanding of qubit error mechanisms but also provide valuable insights into potential error-mitigation strategies for achieving fault tolerance by decoupling superconducting qubits from their mechanical environments. We also present a novel scheme for operating a cQED system in a regime where the cavity is largely displaced. We find that a qubit drive at the bare cavity frequency can effectively displace the cavity field while minimizing the cavity-drive-induced dephasing and the ac Stark shift. Furthermore, we demonstrate that standard cQED protocols, such as qubit control, readout, and cavity single-photon generation, remain compatible with largely displaced cavity fields, even beyond the critical photon number. These findings open new pathways for exploring cQED dynamics in large-photon-number regimes, including the study of nonlinear phenomena in microwave cavities, the saturation of two-level system baths for extending the coherence of microwave quantum states, and the acceleration of the dispersive readout. Finally, mechanical resonators have emerged as integral components in quantum computing for storing and transducing quantum information. Low-frequency mechanical resonators, with extremely low energy dissipation rates, are particularly interesting for extending the lifetimes of stored quantum information. However, integrating low-frequency mechanical resonators with qubits is challenging because their small energy gaps make coherent energy exchange and ground-state preparation difficult. In this thesis, we report the first steps towards the characterization of a hybrid quantum device, consisting of a Transmon qubit and a circuit optomechanical system, both coupled to a 3D microwave cavity.
The basic element of circuit quantum electrodynamics (cQED) is a cavity resonator strongly coupled to a superconducting qubit. Since the inception of the field, the choice of the cavity frequency was, with a few exceptions, been limited to a narrow range around 7 GHz due to a variety of fundamental and practical considerations. Here we report the first cQED implementation, where the qubit remains a regular transmon at about 5 GHz frequency, but the cavity's fundamental mode raises to 21 GHz. We demonstrate that (i) the dispersive shift remains in the conventional MHz range despite the large qubit-cavity detuning, (ii) the quantum efficiency of the qubit readout reaches 8%, (iii) the qubit's energy relaxation quality factor exceeds 107, (iv) the qubit coherence time reproducibly exceeds 100μs and can reach above 300μs with a single echoing π-pulse correction. The readout error is currently limited by an accidental resonant excitation of a non-computational state, the elimination of which requires minor adjustments to the device parameters. Nevertheless, we were able to initialize the qubit in a repeated measurement by post-selection with 2×10−3 error and achieve 4×10−3 state assignment error. These results encourage in-depth explorations of potentially transformative advantages of high-frequency cavities without compromising existing qubit functionality.
In the circuit quantum electrodynamics architecture, both the resonance frequency and the coupling of superconducting qubits to microwave field modes can be controlled via external electric and magnetic fields to explore qubit-photon dynamics in a wide parameter range. Here, we experimentally demonstrate and analyze a scheme for tuning the coupling between a transmon qubit and a microwave resonator using a single coherent drive tone. We treat the transmon as a three-level system, with the qubit subspace defined by the ground and the second excited states. If the drive frequency matches the difference between the resonator and the qubit frequencies, a Jaynes-Cummings-type interaction is induced, which is tunable in both amplitude and phase. We show that coupling strengths of about 10 MHz can be achieved in our setup, limited only by the anharmonicity of the transmon qubit. This scheme has been successfully used to generate microwave photons with a controlled temporal shape [M. Pechal et al., Phys. Rev. X 4, 041010 (2014)] and can be directly implemented with superconducting quantum devices featuring larger anharmonicity for higher coupling strengths.