Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Photonics Research

Multimode-fiber-coupled superconducting nanowire single-photon detector for free-space quantum applications

Hongxin Xu, Jiamin Xiong, Chaomeng Ding, Zhiyun Shu, Yuchi Li, Jingxue Chen, Dianpeng Wang, Xiaoyu Liu, You Xiao, Lixing YOU, Hui Li

Published May 22, 2026• 1 citation
Publisher

Abstract

Multimode fiber (MMF)-coupled superconducting nanowire single-photon detectors (SNSPDs) are critical for free-space quantum communication and sensing, yet their performance is severely limited by polarization-dependent detection efficiency and high dark count rate (DCR) arising from thermal photons. Here, we present a transformative solution that addresses both challenges simultaneously. We demonstrate a polarization-insensitive SNSPD based on a dielectric-compensated bilayer nanowire structure, achieving a system detection efficiency (SDE) of 88% at 1.5 μm with a DCR of ∼4.8×10 4 cps for MMF-coupled signals. To mitigate the elevated thermal noise inherent to multimode coupling, we integrate a compact, dual-stage on-fiber filter with a suppression ratio exceeding 60 dB. The packaged device delivers an SDE of 81% with a DCR of only 4 cps, corresponding to an over 11,000-fold SNR enhancement relative to the unfiltered MMF-coupled configuration.

DOI
10.1364/prj.590928

Related papers

Suppressing Dark Counts of Multimode-Fiber-Coupled Superconducting Nanowire Single-Photon Detector

Chengjun Zhang, Weijun Zhang, Lixing You +9 more

Large active-area superconducting nanowire single-photon detectors (SNSPDs) coupled with multimode fibers (MMFs) can provide high light-gathering capacity, which is essential for free-space detection applications in photon-starved regimes. However, MMF-coupled SNSPDs often suffer from large system dark count rates (DCRsys) over kHz due to blackbody radiation of the MMF at room temperature. Such large DCRsys would significantly degrade signal-to-noise ratio (SNR) of the receiving system. This paper reports an MMF-coupled large-active-area SNSPD system with low DCRsys by using a homemade cryogenic MMF filter bench. The filter bench, which consists of lenses and optical filters, can provide a high transmittance of about 80% at the central wavelength of the passband (1550 ± 12.5 nm) and a wide blocking range from 500 nm to over 6000 nm at 40 K. With using the filter bench, the DCRsys of an MMF-coupled 9-pixel SNSPD array with an active area of 50 μm in diameter is greatly suppressed by 23 dB with 1 dB loss of system detection efficiency (SDE). The detector demonstrates an SDE of 51% at a DCRsys of 100 Hz for 1550 nm photons. Thus, SNR of the detector is enhanced by about 160 times and the noise equivalent power is improved to 3×10-19W/Hz1/2.

IEEE photonics journal•Aug 26, 2019•10 citations

Multimode Fiber Coupled Superconductor Nanowire Single-Photon Detector

Labao Zhang, Ming Gu, Tao Jia +5 more

High-performance superconductor nanowire single-photon detectors (SNSPDs) coupled by 50-μm multimode fiber were designed and fabricated for the purpose of space applications. Microlens coupling between multimode fiber and detector chip was proposed, resulting in coupling efficiency of 86% at the chips with detection area of 15 x 15 μm2. An optical structure for enhancing the photons absorption and superconductor nanowires with low critical current of 3 μA were fabricated on the chips. A cryogenic amplifier was adopted to increase the signal-to-noise ratio and time jitter of output pulse. The SNSPD exhibited system efficiency (1550 nm) of 56% at a dark count rate of 100 cps, 50% at a dark count rate of 5 cps, and 40% at a dark count rate of 1 cps. The time jitter was 46 ps at full-width at half-maximum. The multimode fiber coupling system with high performance will promote its applications in free space.

IEEE photonics journal•Sep 25, 2014•16 citations

Fiber-coupled superconducting nanowire single-photon detectors integrated with a bandpass filter on the fiber end-face

Weijun Zhang, Xiaoyan Yang, Hao Li +7 more

Abstract Superconducting nanowire single-photon detectors (SNSPDs) with both high system detection efficiency (SDE) and low dark count rate (DCR) play significant roles in quantum information processes and various applications. The background dark counts of SNSPDs originate from the room temperature blackbody radiation coupled to the device via a fiber. Therefore, a bandpass filter (BPF) operated at low temperature with minimal insert loss is necessary to suppress the background DCR. Herein, a low-loss BPF integrated on a single-mode fiber end-face was designed, fabricated and verified for the low temperature implement. The fiber end-face BPF was featured with a typical passband width about 40 nm in the 1550 nm telecom band and a peak transmittance of over 0.98. SNSPD with high SDE fabricated on a distributed Bragg reflector was coupled to the BPF. The device with such a BPF showed an SDE of 80% at a DCR of 0.5 Hz, measured at 2.1 K. Compared the same device without a BPF, the DCR was reduced by over 13 dB with an SDE decrease of <3%.

Superconductor Science and Technology•Jan 10, 2018•56 citations

Investigation of the Performance of an Ultralow-Dark-Count Superconducting Nanowire Single-Photon Detector

Shanthi Subashchandran, Ryo Okamoto, Labao Zhang +6 more

The realization of an ultralow-dark-count rate (DCR) along with the conservation of high detection efficiency (DE) is critical for many applications using single photon detectors in quantum information technologies, material sciences, and biological sensing. For this purpose, a fiber-coupled superconducting nanowire single-photon detector (SNSPD) with a meander-type niobium nitride nanowire (width: 50 nm) is studied. Precise measurements of the bias current dependence of DE are carried out for a wide spectral range (from 500 to 1650 nm in steps of 50 nm) using a white light source and a laser line Bragg tunable band-pass filter. An ultralow DCR (0.0015 cps) and high DE (32%) are simultaneously achieved by the SNSPD at a wavelength of 500 nm.

Japanese Journal of Applied Physics•Oct 1, 2013•11 citations

High-efficiency 8 × 8 superconducting nanowire single-photon detector array coupled with a 105-μm multimode fiber

Zhen Wan, Jia Huang, You Xiao +8 more

We present an 8 × 8 superconducting nanowire single-photon detector (SNSPD) array that addresses the trade-off between detection efficiency and count rates in large-area devices.The SNSPD array employs a distributed nanowire architecture and a polarization-insensitive optical cavity, when coupled with a 105-μm multimode fiber, achieves a system detection efficiency of 75% at 1064 nm with a count rate of 945 MHz at 3 dB compression and an average timing jitter of <100 ps.This design offers a scalable solution for high-speed photon counting with large-area detection and multimode compatibility.

Chinese Optics Letters•Jan 1, 2025•0 citations

Micro-fiber coupled superconducting nanowire single photon detector (Conference Presentation)

Lixing You

Ever since superconducting nanowire single-photon detectors (SNSPDs or SSPDs) were demonstrated, they have attracted a considerable attention due to the detectors’ promising performance that includes high detection efficiency (DE), low dark count rate (DCR), broadband sensitivity, and low timing jitter. The system detection efficiency (SDE) has been improved to be over 90% with a wavelength of 1550 nm in a fiber-coupled system by embedding the SNSPD in optical cavities. However, the implementation of optical cavity usually reduces the bandwidth of SNSPDs. As a result, there are some recent works on increasing the bandwidth of SNSPD. Furthermore, the size of the active area of meandered nanowires has to be compatible with the core size of an optical fiber such that good optical coupling can be achieved; this setup requires a long nanowire with a large kinetic inductance, thus resulting in a small counting rate and a large timing jitter, particularly for multi-mode fiber-coupled devices. Nevertheless, a particularly impressive waveguide-coupled SNSPD has been developed in recent years. By placing an SNSPD atop an optical waveguide that has been fabricated on various substrate materials, photons propagating in the waveguide have been found to be evanescently absorbed by nanowires that are only a few tens of microns long. The on-chip DE of this device has been estimated to be over 90%, thus indicating that it has both high absorptance and high intrinsic DE. If the waveguide and the nanowire are correctly dimensioned, the absorptance of this device can reach over 90% for a wavelength range of more than 700 nm. Furthermore, the length of the nanowire is shorter than that of the fiber-coupled SNSPD, thus leading to a higher count rate and lower timing jitter (~18 ps). However, unsatisfactory coupling losses between the optical fiber and the waveguide in such devices can decrease its SDE (~10%), thus limiting its applicability to quantum photonic integrated circuits (QPIC). Recently, we proposed a type of SNSPD that was coupled with microfibers (MFs), and simulations for this SNSPD indicated that its absorption would be as high as 90%. Microfibers and nanofibers, tapered adiabatically from standard fibers, with diameters close to or smaller than the wavelength of the guided light were demonstrated to have low transmittance losses by Tong et al. in 2003. MFs have been shown to have many interesting properties, such as strong evanescent fields, tight optical confinement, wideband abilities, and small masses; these properties are appealing for applications such as optical sensing and coupling. MFs also provide seamless connections with high transmittance from standard fibers; therefore, MF-coupled SNSPDs can achieve both high SDEs and wideband compatibility. We proposed and demonstrated the MF-coupled SNSPDs successfully. The simulation results indicate that with optimal device structure, the optical absorption with efficiency < 90% can be realized over a wavelength range of 350 nm to 2150 nm. The fabricated MF-coupled SNSPD, shows unparalleled broadband system detection efficiencies (SDEs) of more than 50% from 630 nm to 1500 nm. The SDEs reach 66% at 785 nm and 45% at 1550 nm. These results pave the way for ultra-broadband weak light detection with quantum-limit sensitivity.

Advanced Photon Counting Techniques•May 1, 2020•0 citations
Multimode fiber (MMF)-coupled superconducting nanowire single-photon detectors (SNSPDs) are critical for free-space quantum communication and sensing, yet their performance is severely limited by polarization-dependent detection efficiency and high dark count rate (DCR) arising from thermal photons. Here, we present a transformative solution that addresses both challenges simultaneously. We demonstrate a polarization-insensitive SNSPD based on a dielectric-compensated bilayer nanowire structure, achieving a system detection efficiency (SDE) of 88% at 1.5 μm with a DCR of ∼4.8×10 4 cps for MMF-coupled signals. To mitigate the elevated thermal noise inherent to multimode coupling, we integrate a compact, dual-stage on-fiber filter with a suppression ratio exceeding 60 dB. The packaged device delivers an SDE of 81% with a DCR of only 4 cps, corresponding to an over 11,000-fold SNR enhancement relative to the unfiltered MMF-coupled configuration.
Large active-area superconducting nanowire single-photon detectors (SNSPDs) coupled with multimode fibers (MMFs) can provide high light-gathering capacity, which is essential for free-space detection applications in photon-starved regimes. However, MMF-coupled SNSPDs often suffer from large system dark count rates (DCRsys) over kHz due to blackbody radiation of the MMF at room temperature. Such large DCRsys would significantly degrade signal-to-noise ratio (SNR) of the receiving system. This paper reports an MMF-coupled large-active-area SNSPD system with low DCRsys by using a homemade cryogenic MMF filter bench. The filter bench, which consists of lenses and optical filters, can provide a high transmittance of about 80% at the central wavelength of the passband (1550 ± 12.5 nm) and a wide blocking range from 500 nm to over 6000 nm at 40 K. With using the filter bench, the DCRsys of an MMF-coupled 9-pixel SNSPD array with an active area of 50 μm in diameter is greatly suppressed by 23 dB with 1 dB loss of system detection efficiency (SDE). The detector demonstrates an SDE of 51% at a DCRsys of 100 Hz for 1550 nm photons. Thus, SNR of the detector is enhanced by about 160 times and the noise equivalent power is improved to 3×10-19W/Hz1/2.
High-performance superconductor nanowire single-photon detectors (SNSPDs) coupled by 50-μm multimode fiber were designed and fabricated for the purpose of space applications. Microlens coupling between multimode fiber and detector chip was proposed, resulting in coupling efficiency of 86% at the chips with detection area of 15 x 15 μm2. An optical structure for enhancing the photons absorption and superconductor nanowires with low critical current of 3 μA were fabricated on the chips. A cryogenic amplifier was adopted to increase the signal-to-noise ratio and time jitter of output pulse. The SNSPD exhibited system efficiency (1550 nm) of 56% at a dark count rate of 100 cps, 50% at a dark count rate of 5 cps, and 40% at a dark count rate of 1 cps. The time jitter was 46 ps at full-width at half-maximum. The multimode fiber coupling system with high performance will promote its applications in free space.
Abstract Superconducting nanowire single-photon detectors (SNSPDs) with both high system detection efficiency (SDE) and low dark count rate (DCR) play significant roles in quantum information processes and various applications. The background dark counts of SNSPDs originate from the room temperature blackbody radiation coupled to the device via a fiber. Therefore, a bandpass filter (BPF) operated at low temperature with minimal insert loss is necessary to suppress the background DCR. Herein, a low-loss BPF integrated on a single-mode fiber end-face was designed, fabricated and verified for the low temperature implement. The fiber end-face BPF was featured with a typical passband width about 40 nm in the 1550 nm telecom band and a peak transmittance of over 0.98. SNSPD with high SDE fabricated on a distributed Bragg reflector was coupled to the BPF. The device with such a BPF showed an SDE of 80% at a DCR of 0.5 Hz, measured at 2.1 K. Compared the same device without a BPF, the DCR was reduced by over 13 dB with an SDE decrease of <3%.
The realization of an ultralow-dark-count rate (DCR) along with the conservation of high detection efficiency (DE) is critical for many applications using single photon detectors in quantum information technologies, material sciences, and biological sensing. For this purpose, a fiber-coupled superconducting nanowire single-photon detector (SNSPD) with a meander-type niobium nitride nanowire (width: 50 nm) is studied. Precise measurements of the bias current dependence of DE are carried out for a wide spectral range (from 500 to 1650 nm in steps of 50 nm) using a white light source and a laser line Bragg tunable band-pass filter. An ultralow DCR (0.0015 cps) and high DE (32%) are simultaneously achieved by the SNSPD at a wavelength of 500 nm.
We present an 8 × 8 superconducting nanowire single-photon detector (SNSPD) array that addresses the trade-off between detection efficiency and count rates in large-area devices.The SNSPD array employs a distributed nanowire architecture and a polarization-insensitive optical cavity, when coupled with a 105-μm multimode fiber, achieves a system detection efficiency of 75% at 1064 nm with a count rate of 945 MHz at 3 dB compression and an average timing jitter of <100 ps.This design offers a scalable solution for high-speed photon counting with large-area detection and multimode compatibility.
Ever since superconducting nanowire single-photon detectors (SNSPDs or SSPDs) were demonstrated, they have attracted a considerable attention due to the detectors’ promising performance that includes high detection efficiency (DE), low dark count rate (DCR), broadband sensitivity, and low timing jitter. The system detection efficiency (SDE) has been improved to be over 90% with a wavelength of 1550 nm in a fiber-coupled system by embedding the SNSPD in optical cavities. However, the implementation of optical cavity usually reduces the bandwidth of SNSPDs. As a result, there are some recent works on increasing the bandwidth of SNSPD. Furthermore, the size of the active area of meandered nanowires has to be compatible with the core size of an optical fiber such that good optical coupling can be achieved; this setup requires a long nanowire with a large kinetic inductance, thus resulting in a small counting rate and a large timing jitter, particularly for multi-mode fiber-coupled devices. Nevertheless, a particularly impressive waveguide-coupled SNSPD has been developed in recent years. By placing an SNSPD atop an optical waveguide that has been fabricated on various substrate materials, photons propagating in the waveguide have been found to be evanescently absorbed by nanowires that are only a few tens of microns long. The on-chip DE of this device has been estimated to be over 90%, thus indicating that it has both high absorptance and high intrinsic DE. If the waveguide and the nanowire are correctly dimensioned, the absorptance of this device can reach over 90% for a wavelength range of more than 700 nm. Furthermore, the length of the nanowire is shorter than that of the fiber-coupled SNSPD, thus leading to a higher count rate and lower timing jitter (~18 ps). However, unsatisfactory coupling losses between the optical fiber and the waveguide in such devices can decrease its SDE (~10%), thus limiting its applicability to quantum photonic integrated circuits (QPIC). Recently, we proposed a type of SNSPD that was coupled with microfibers (MFs), and simulations for this SNSPD indicated that its absorption would be as high as 90%. Microfibers and nanofibers, tapered adiabatically from standard fibers, with diameters close to or smaller than the wavelength of the guided light were demonstrated to have low transmittance losses by Tong et al. in 2003. MFs have been shown to have many interesting properties, such as strong evanescent fields, tight optical confinement, wideband abilities, and small masses; these properties are appealing for applications such as optical sensing and coupling. MFs also provide seamless connections with high transmittance from standard fibers; therefore, MF-coupled SNSPDs can achieve both high SDEs and wideband compatibility. We proposed and demonstrated the MF-coupled SNSPDs successfully. The simulation results indicate that with optimal device structure, the optical absorption with efficiency < 90% can be realized over a wavelength range of 350 nm to 2150 nm. The fabricated MF-coupled SNSPD, shows unparalleled broadband system detection efficiencies (SDEs) of more than 50% from 630 nm to 1500 nm. The SDEs reach 66% at 785 nm and 45% at 1550 nm. These results pave the way for ultra-broadband weak light detection with quantum-limit sensitivity.