Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Optics Letters

High-efficiency 8 × 8 superconducting nanowire single-photon detector array coupled with a 105-μm multimode fiber

Zhen Wan, Jia Huang, You Xiao, Chaomeng Ding, Huiqin Yu, Xiaofu Zhang, Xiaoyu Liu, Chaolin Lv, Hao Li, Lixing You, Zhen Wang

Published Jan 1, 2025• 0 citations
Publisher

Abstract

We present an 8 × 8 superconducting nanowire single-photon detector (SNSPD) array that addresses the trade-off between detection efficiency and count rates in large-area devices.The SNSPD array employs a distributed nanowire architecture and a polarization-insensitive optical cavity, when coupled with a 105-μm multimode fiber, achieves a system detection efficiency of 75% at 1064 nm with a count rate of 945 MHz at 3 dB compression and an average timing jitter of <100 ps.This design offers a scalable solution for high-speed photon counting with large-area detection and multimode compatibility.

DOI
10.3788/col202523.122501

Related papers

Sixteen-channel fiber array-coupled superconducting single-photon detector array with average system detection efficiency over 60% at telecom wavelength

Weijun Zhang, Guangzhao Xu, Lixing You +8 more

We report a compact, scalable, and high-performance superconducting nanowire single-photon detector (SNSPD) array by using a multichannel optical fiber array-coupled configuration. For single pixels with an active area of 18 µm in diameter and illuminated at the telecom wavelength of 1550 nm, we achieved a pixel yield of 13/16 on one chip, an average system detection efficiency of 69% at a dark count rate of 160 cps, a minimum timing jitter of 74 ps, and a maximum count rate of ∼ 40 M c p s . The optical crosstalk coefficient between adjacent channels is better than − 60 d B . The performance of the fiber array-coupled detectors is comparable with a standalone detector coupled to a single fiber. Our method is promising for the development of scalable, high-performance, and high-yield SNSPDs.

arXiv:2101.01556•Optics Letters•Jan 28, 2021•7 citations

Large-sensitive-area superconducting nanowire single-photon detector at 850 nm with high detection efficiency

Hao Li, Lu Zhang, Lixing You +6 more

Satellite-ground quantum communication requires single-photon detectors of 850-nm wavelength with both high detection efficiency and large sensitive area. We developed superconducting nanowire single-photon detectors (SNSPDs) on one-dimensional photonic crystals, which acted as optical cavities to enhance the optical absorption, with a sensitive-area diameter of 50 μm. The fabricated multimode fiber coupled NbN SNSPDs exhibited a maximum system detection efficiency (DE) of up to 82% and a DE of 78% at a dark count rate of 100 Hz at 850-nm wavelength as well as a system jitter of 105 ps.

arXiv:1506.07922•Optics Express•Jun 24, 2015•43 citations

Multimode fiber-coupled superconducting nanowire single-photon detector with 70% system efficiency at visible wavelength

Dengkuan Liu, Shigehito Miki, Taro Yamashita +3 more

We report the development of the multimode fiber-coupled superconducting nanowire single-photon detector with high system detection efficiency at visible wavelength. The detector consists of a 10.5-nm-thick and 150-nm-wide NbN nanowire meander fabricated on a Si substrate with a multilayer dielectric mirror and a quarter wavelength cavity for obtaining high optical absorptance. The meander area was 35 µm in diameter and coupled with the GRIN-lensed multimode optical fiber with a core diameter of 50 µm. The system reached detection efficiency of 70% with dark count rate of 100 Hz at the wavelength of 635 nm, 3 dB roll-off response counting rate of 8.5 Mcps, and timing jitter of 76 ps.

Optics Express•Aug 25, 2014•37 citations

Multimode Fiber Coupled Superconductor Nanowire Single-Photon Detector

Labao Zhang, Ming Gu, Tao Jia +5 more

High-performance superconductor nanowire single-photon detectors (SNSPDs) coupled by 50-μm multimode fiber were designed and fabricated for the purpose of space applications. Microlens coupling between multimode fiber and detector chip was proposed, resulting in coupling efficiency of 86% at the chips with detection area of 15 x 15 μm2. An optical structure for enhancing the photons absorption and superconductor nanowires with low critical current of 3 μA were fabricated on the chips. A cryogenic amplifier was adopted to increase the signal-to-noise ratio and time jitter of output pulse. The SNSPD exhibited system efficiency (1550 nm) of 56% at a dark count rate of 100 cps, 50% at a dark count rate of 5 cps, and 40% at a dark count rate of 1 cps. The time jitter was 46 ps at full-width at half-maximum. The multimode fiber coupling system with high performance will promote its applications in free space.

IEEE photonics journal•Sep 25, 2014•16 citations

Broadband waveguide-integrated superconducting single-photon detectors with high system detection efficiency

Martin A. Wolff, Fabian Beutel, Jonas Schütte +4 more

Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.

Applied Physics Letters•Apr 12, 2021•43 citations

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations
We present an 8 × 8 superconducting nanowire single-photon detector (SNSPD) array that addresses the trade-off between detection efficiency and count rates in large-area devices.The SNSPD array employs a distributed nanowire architecture and a polarization-insensitive optical cavity, when coupled with a 105-μm multimode fiber, achieves a system detection efficiency of 75% at 1064 nm with a count rate of 945 MHz at 3 dB compression and an average timing jitter of <100 ps.This design offers a scalable solution for high-speed photon counting with large-area detection and multimode compatibility.
We report a compact, scalable, and high-performance superconducting nanowire single-photon detector (SNSPD) array by using a multichannel optical fiber array-coupled configuration. For single pixels with an active area of 18 µm in diameter and illuminated at the telecom wavelength of 1550 nm, we achieved a pixel yield of 13/16 on one chip, an average system detection efficiency of 69% at a dark count rate of 160 cps, a minimum timing jitter of 74 ps, and a maximum count rate of ∼ 40 M c p s . The optical crosstalk coefficient between adjacent channels is better than − 60 d B . The performance of the fiber array-coupled detectors is comparable with a standalone detector coupled to a single fiber. Our method is promising for the development of scalable, high-performance, and high-yield SNSPDs.
Satellite-ground quantum communication requires single-photon detectors of 850-nm wavelength with both high detection efficiency and large sensitive area. We developed superconducting nanowire single-photon detectors (SNSPDs) on one-dimensional photonic crystals, which acted as optical cavities to enhance the optical absorption, with a sensitive-area diameter of 50 μm. The fabricated multimode fiber coupled NbN SNSPDs exhibited a maximum system detection efficiency (DE) of up to 82% and a DE of 78% at a dark count rate of 100 Hz at 850-nm wavelength as well as a system jitter of 105 ps.
We report the development of the multimode fiber-coupled superconducting nanowire single-photon detector with high system detection efficiency at visible wavelength. The detector consists of a 10.5-nm-thick and 150-nm-wide NbN nanowire meander fabricated on a Si substrate with a multilayer dielectric mirror and a quarter wavelength cavity for obtaining high optical absorptance. The meander area was 35 µm in diameter and coupled with the GRIN-lensed multimode optical fiber with a core diameter of 50 µm. The system reached detection efficiency of 70% with dark count rate of 100 Hz at the wavelength of 635 nm, 3 dB roll-off response counting rate of 8.5 Mcps, and timing jitter of 76 ps.
High-performance superconductor nanowire single-photon detectors (SNSPDs) coupled by 50-μm multimode fiber were designed and fabricated for the purpose of space applications. Microlens coupling between multimode fiber and detector chip was proposed, resulting in coupling efficiency of 86% at the chips with detection area of 15 x 15 μm2. An optical structure for enhancing the photons absorption and superconductor nanowires with low critical current of 3 μA were fabricated on the chips. A cryogenic amplifier was adopted to increase the signal-to-noise ratio and time jitter of output pulse. The SNSPD exhibited system efficiency (1550 nm) of 56% at a dark count rate of 100 cps, 50% at a dark count rate of 5 cps, and 40% at a dark count rate of 1 cps. The time jitter was 46 ps at full-width at half-maximum. The multimode fiber coupling system with high performance will promote its applications in free space.
Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.