Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE photonics journal

Reception of a Broadband Noise-Like Spread Spectrum Waveform Using a Rydberg Atom-Based Quantum RF Receiver

Hoang-Van Do, David Bair, Eric Bottomley, Seth C. Caliga, Dean Zody, Ronald M. Reano

Published Apr 9, 2026• 0 citations
Publisher

Abstract

We present experimental results demonstrating broadband reception of a noise-like spread-spectrum waveform using a Rydberg atom-based quantum radio frequency (RF) receiver. The transmitted waveform occupies a 20 MHz bandwidth around a 2.5 GHz carrier and is intentionally engineered to exhibit noise-like spectral characteristics. To enable recovery of this broadband signal, the Rydberg sensor was configured to achieve sufficiently uniform sensitivity across intermediate frequencies up to 10 MHz (corresponding to a ±10 MHz signal band about the carrier, i.e., 20 MHz total bandwidth). Under these conditions, we demonstrate successful detection and recovery of noise-like spread-spectrum waveforms spanning a 20 MHz bandwidth. These results validate the feasibility of using atomic sensors for broadband RF waveform reception and highlight their potential in photonics-enabled RF sensing applications.

DOI
10.1109/jphot.2026.3682599

Related papers

Probing bandwidth and sensitivity in Rydberg atom sensing via optical homodyne and rf heterodyne detection

Dixith Manchaiah, Stone Oliver, Samuel Berweger +2 more

Rydberg atom based sensors allow for SI traceable measurements and show promise for applications in the field of communication and radar technologies. In this article, we investigate the bandwidth and sensitivity of a Rydberg atom-based sensor in a rubidium vapor cell using Rydberg electromagnetically induced transparency (EIT) spectroscopy. We employ a radio-frequency (RF) heterodyne measurement technique in combination with an optical homodyne setup to extend the achievable range between sensitivity and bandwidth in a Rydberg sensor. While the bandwidth of Rydberg sensors are limited by the transit time of atoms and the Rabi frequency of the coupling field, achieving higher bandwidth through smaller beam sizes is thought to compromise sensitivity due to reduced EIT signal strength. Using optical homodyne detection, we demonstrate that sensitivity is preserved while achieving a response bandwidth of 8 MHz. In addition, using the Rydberg sensor, we receive digital communication signals and present error vector magnitude (EVM) measurements as a function of varying symbol rates and bandwidth of the Rydberg sensor. Furthermore, the sensor's performance is compared with a conventional RF mixer. We establish that the bandwidth of a Rydberg sensor when receiving a pure tone is not the same as the bandwidth of the sensor when receiving a modulated signal. This difference results from the spreading of symbols in the frequency domain, leading to a reduction of the signal to noise ratio (SNR) and an accumulation of noise over the total span of the modulated signal.

arXiv:2509.20632•Physical Review A•Dec 22, 2025•5 citations

Rydberg-atom-based digital communication using a continuously tunable radio-frequency carrier

Zhenfei Song, Hongping Liu, Xiaochi Liu +4 more

Up to now, the measurement of radio-frequency (RF) electric field achieved using the electromagnetically-induced transparency (EIT) of Rydberg atoms has proved to be of high-sensitivity and shows a potential to produce a promising atomic RF receiver at resonance between two chosen Rydberg states. In this paper, we study the extension of the feasibility of digital communication via this quantum-based antenna over a continuously tunable RF-carrier at off-resonance. Our experiment shows that the digital communication at a rate of 500 kbps can be performed reliably within a tunable bandwidth of 200 MHz near a 10.22 GHz carrier. Outside of this range, the bit error rate (BER) increases, rising to, for example, 15% at an RF-detuning of ±150 MHz. In the measurement, the time-varying RF field is retrieved by detecting the optical power of the probe laser at the center frequency of RF-induced symmetric or asymmetric Autler-Townes splitting in EIT. Prior to the digital test, we studied the RF-reception quality as a function of various parameters including the RF detuning and found that a choice of linear gain response to the RF-amplitude can suppress the signal distortion. The modulating signal can be decoded at speeds up to 500 kHz in the tunable bandwidth. Our test consolidates the physical basis for reliable communication and spectral sensing over a wider broadband RF-carrier, which paves a way for the concurrent multi-channel communications founded on the same pair of Rydberg states.

arXiv:1808.10839•Optics Express•Mar 12, 2019•175 citations

Quantum-Based Amplitude Modulation Radio Receiver Using Rydberg Atoms

Zhenfei Song, Wanfeng Zhang, Xiaochi Liu +4 more

The highly-excited Rydberg states are with a unique property of radio-frequency (RF) resonance, and Rydberg atoms at room temperature are promising for developing a broadband RF electric field sensor and relevant metrology standards. In this paper, the working mechanism of an atomic amplitude-modulation(AM) radio receiver is investigated in detail, and various factors affecting the communication quality are discussed. The modulation RF signal can be directly retrieved by measuring the transmission of a probe laser at resonance of rubidium D2 transition using a fast photo-diode detector, without any conventional demodulation process. Various communication experiments are tested at a 10.22 GHz carrier, and a modulation bandwidth of 1 MHz and an acceptable data transfer rate of about 1 Mbps have been achieved using current detection techniques. Owing to a potential high sensitivity and ultra-broadband capability of free-space RF field sensing, the quantum receiver has great significance compared with conventional electronics-based receivers, including but not limited to a weak signal, long-distance, and broadband communication in free space or via a fiber link.

IEEE Globecom Workshops (GC Wkshps)•Dec 1, 2018•8 citations

Shortwave frequency-hopping reception via a Rydberg atom-based electrically small antenna

Siyuan Qiu, Hong-Lei Wang, X. -Q Liu +7 more

There is an inherent trade-off in shortwave (SW) signal reception between achieving wide operational bandwidth and high radio sensitivity. Advances in SW radio reception hold significant potential for applications in communications, broadcasting, and over-the-horizon radar. Here, we demonstrate a proof-of-concept Rydberg SW receiver integrated with the frequency-hopping technique, achieving a highly sensitive reception compatible with large bandwidth. By shifting a carrier across the whole SW band, the atomic communication maintains a stable and high data capacity far beyond the Chu–Harrington limit. The outcomes of our work facilitate the development of Rydberg atom-based RF field sensing and communication.

Applied Physics Letters•Jan 19, 2026•1 citation

Ultra-broadband Anti-Jamming Communication via a Rydberg Atomic Receiver

Jia-Dou Nan, Junrong Chen, Bang Liu +11 more

Ultra-broadband anti-jamming communication represents a promising approach to secure and robust information transfer through spread-spectrum techniques, effectively combatting malicious interference and eavesdropping. Rydberg atoms, enhanced by waveguide coupling, facilitate ultra-broadband spectrum sensing without traditional RF components. This framework provides an experimental platform for ultra-wide anti-jamming communication. Here, we demonstrate real-time signal demodulation based on frequency-hopping spread spectrum (FHSS) in a waveguide-coupled Rydberg receiver, achieving ultra-broad frequency-hopping covering 100 kHz to 20 GHz and a hopping rate of 100 khop/s. When confined to a standard operational band (e.g., the 2.4 GHz ISM band), our system achieves a high channel density of 8 channels per MHz. Beyond this, by leveraging its ultra-broad and continuous bandwidth, the system supports over 150,000 channels. Experimental results reveal a 51 dB enhancement in narrowband interference tolerance compared with single-frequency systems, confirming its outstanding anti-jamming capability. The reported system demonstrates significant potential for secure communications based on quantum technology, especially communication in complex electromagnetic environments.

arXiv:2606.14497•Jun 12, 2026•0 citations

Rydberg Atoms for Radio-Frequency Communications and Sensing: Atomic Receivers for Pulsed RF Field and Phase Detection

David Alexander Anderson, Rachel Sapiro, Georg A. Raithel

We report on the development of detection methods for amplitude and phase of pulsed radio-frequency (RF) electromagnetic fields with Rydberg atoms. We begin with an overview of the basic principles of Rydberg-atom-based sensing and measurement of RF electromagnetic fields. An overview of the underlying atomic physics and the method for amplitude as well as phase sensing of electromagnetic radiation with Rydberg atoms is provided. Atomic RF receivers using Rydberg atoms for analog and digital communications and sensing of modulated RF fields are discussed. Detection of pulse-modulated RF and time-domain RF pulse waveform imaging with a Rydberg-atom receiver are demonstrated. The transient response of the Rydberg-atom vapor to a modulated RF field is observed at the 10-nanosecond level, from which a new lower limit to the achievable instantaneous signal bandwidth of atomic RF receivers is established. Finally, we present and describe a new method to measure the phase of an RF field implemented to not require an RF reference wave. The method employs phase-coherent excitation pathways involving the optical fields in the atomic sensing medium with the signal RF field. The optical RF phase-sensing approach lends itself to the realization of atomic RF sensors, measurement and imaging devices that are relevant to applications in RF communications and sensing.

arXiv:1910.07970•IEEE Aerospace and Electronic Systems Magazine•Apr 1, 2020•85 citations
We present experimental results demonstrating broadband reception of a noise-like spread-spectrum waveform using a Rydberg atom-based quantum radio frequency (RF) receiver. The transmitted waveform occupies a 20 MHz bandwidth around a 2.5 GHz carrier and is intentionally engineered to exhibit noise-like spectral characteristics. To enable recovery of this broadband signal, the Rydberg sensor was configured to achieve sufficiently uniform sensitivity across intermediate frequencies up to 10 MHz (corresponding to a ±10 MHz signal band about the carrier, i.e., 20 MHz total bandwidth). Under these conditions, we demonstrate successful detection and recovery of noise-like spread-spectrum waveforms spanning a 20 MHz bandwidth. These results validate the feasibility of using atomic sensors for broadband RF waveform reception and highlight their potential in photonics-enabled RF sensing applications.
Rydberg atom based sensors allow for SI traceable measurements and show promise for applications in the field of communication and radar technologies. In this article, we investigate the bandwidth and sensitivity of a Rydberg atom-based sensor in a rubidium vapor cell using Rydberg electromagnetically induced transparency (EIT) spectroscopy. We employ a radio-frequency (RF) heterodyne measurement technique in combination with an optical homodyne setup to extend the achievable range between sensitivity and bandwidth in a Rydberg sensor. While the bandwidth of Rydberg sensors are limited by the transit time of atoms and the Rabi frequency of the coupling field, achieving higher bandwidth through smaller beam sizes is thought to compromise sensitivity due to reduced EIT signal strength. Using optical homodyne detection, we demonstrate that sensitivity is preserved while achieving a response bandwidth of 8 MHz. In addition, using the Rydberg sensor, we receive digital communication signals and present error vector magnitude (EVM) measurements as a function of varying symbol rates and bandwidth of the Rydberg sensor. Furthermore, the sensor's performance is compared with a conventional RF mixer. We establish that the bandwidth of a Rydberg sensor when receiving a pure tone is not the same as the bandwidth of the sensor when receiving a modulated signal. This difference results from the spreading of symbols in the frequency domain, leading to a reduction of the signal to noise ratio (SNR) and an accumulation of noise over the total span of the modulated signal.
Up to now, the measurement of radio-frequency (RF) electric field achieved using the electromagnetically-induced transparency (EIT) of Rydberg atoms has proved to be of high-sensitivity and shows a potential to produce a promising atomic RF receiver at resonance between two chosen Rydberg states. In this paper, we study the extension of the feasibility of digital communication via this quantum-based antenna over a continuously tunable RF-carrier at off-resonance. Our experiment shows that the digital communication at a rate of 500 kbps can be performed reliably within a tunable bandwidth of 200 MHz near a 10.22 GHz carrier. Outside of this range, the bit error rate (BER) increases, rising to, for example, 15% at an RF-detuning of ±150 MHz. In the measurement, the time-varying RF field is retrieved by detecting the optical power of the probe laser at the center frequency of RF-induced symmetric or asymmetric Autler-Townes splitting in EIT. Prior to the digital test, we studied the RF-reception quality as a function of various parameters including the RF detuning and found that a choice of linear gain response to the RF-amplitude can suppress the signal distortion. The modulating signal can be decoded at speeds up to 500 kHz in the tunable bandwidth. Our test consolidates the physical basis for reliable communication and spectral sensing over a wider broadband RF-carrier, which paves a way for the concurrent multi-channel communications founded on the same pair of Rydberg states.
The highly-excited Rydberg states are with a unique property of radio-frequency (RF) resonance, and Rydberg atoms at room temperature are promising for developing a broadband RF electric field sensor and relevant metrology standards. In this paper, the working mechanism of an atomic amplitude-modulation(AM) radio receiver is investigated in detail, and various factors affecting the communication quality are discussed. The modulation RF signal can be directly retrieved by measuring the transmission of a probe laser at resonance of rubidium D2 transition using a fast photo-diode detector, without any conventional demodulation process. Various communication experiments are tested at a 10.22 GHz carrier, and a modulation bandwidth of 1 MHz and an acceptable data transfer rate of about 1 Mbps have been achieved using current detection techniques. Owing to a potential high sensitivity and ultra-broadband capability of free-space RF field sensing, the quantum receiver has great significance compared with conventional electronics-based receivers, including but not limited to a weak signal, long-distance, and broadband communication in free space or via a fiber link.
There is an inherent trade-off in shortwave (SW) signal reception between achieving wide operational bandwidth and high radio sensitivity. Advances in SW radio reception hold significant potential for applications in communications, broadcasting, and over-the-horizon radar. Here, we demonstrate a proof-of-concept Rydberg SW receiver integrated with the frequency-hopping technique, achieving a highly sensitive reception compatible with large bandwidth. By shifting a carrier across the whole SW band, the atomic communication maintains a stable and high data capacity far beyond the Chu–Harrington limit. The outcomes of our work facilitate the development of Rydberg atom-based RF field sensing and communication.
Ultra-broadband anti-jamming communication represents a promising approach to secure and robust information transfer through spread-spectrum techniques, effectively combatting malicious interference and eavesdropping. Rydberg atoms, enhanced by waveguide coupling, facilitate ultra-broadband spectrum sensing without traditional RF components. This framework provides an experimental platform for ultra-wide anti-jamming communication. Here, we demonstrate real-time signal demodulation based on frequency-hopping spread spectrum (FHSS) in a waveguide-coupled Rydberg receiver, achieving ultra-broad frequency-hopping covering 100 kHz to 20 GHz and a hopping rate of 100 khop/s. When confined to a standard operational band (e.g., the 2.4 GHz ISM band), our system achieves a high channel density of 8 channels per MHz. Beyond this, by leveraging its ultra-broad and continuous bandwidth, the system supports over 150,000 channels. Experimental results reveal a 51 dB enhancement in narrowband interference tolerance compared with single-frequency systems, confirming its outstanding anti-jamming capability. The reported system demonstrates significant potential for secure communications based on quantum technology, especially communication in complex electromagnetic environments.
We report on the development of detection methods for amplitude and phase of pulsed radio-frequency (RF) electromagnetic fields with Rydberg atoms. We begin with an overview of the basic principles of Rydberg-atom-based sensing and measurement of RF electromagnetic fields. An overview of the underlying atomic physics and the method for amplitude as well as phase sensing of electromagnetic radiation with Rydberg atoms is provided. Atomic RF receivers using Rydberg atoms for analog and digital communications and sensing of modulated RF fields are discussed. Detection of pulse-modulated RF and time-domain RF pulse waveform imaging with a Rydberg-atom receiver are demonstrated. The transient response of the Rydberg-atom vapor to a modulated RF field is observed at the 10-nanosecond level, from which a new lower limit to the achievable instantaneous signal bandwidth of atomic RF receivers is established. Finally, we present and describe a new method to measure the phase of an RF field implemented to not require an RF reference wave. The method employs phase-coherent excitation pathways involving the optical fields in the atomic sensing medium with the signal RF field. The optical RF phase-sensing approach lends itself to the realization of atomic RF sensors, measurement and imaging devices that are relevant to applications in RF communications and sensing.