Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Sensors

A New Mathematical Framework for CMOS Si Photomultiplier Detection Rates in Quantum Cryptography

Tal Gofman, Yael Nemirovsky

Published Feb 22, 2026• 0 citations
Publisher

Abstract

The deployment of Discrete Variable Quantum Key Distribution (DV-QKD) in high-traffic, short-reach environments, such as intra-data center networks, is currently constrained by the saturation of single-photon detectors. While CMOS Single-Photon Avalanche Diodes (SPADs) offer a cost-effective solution, their Secure Key Rate (SKR) is limited by detector dead time. To the best of the authors' knowledge, this work is the first to derive a generalized detection rate model for SiPMs that addresses the dead-time bottlenecks of gigahertz-rate quantum cryptography. While methods for managing deadtime via active optical switching have been proposed, our model quantifies the benefits of passive spatial multiplexing inherent in standard SiPM arrays. Furthermore, contrasting with models designed to optimize energy resolution or characterize nonlinear charge response to light pulses, our work focuses on maximizing the detection count rate. We derive exact detection rate models for both analog (paralyzable) and digital (non-paralyzable) SiPM architectures, incorporating correlated noise sources such as optical crosstalk and afterpulsing. Simulation results indicate that SiPMs can increase detection rates by over an order of magnitude compared to single SPADs.

DOI
10.3390/s26041386

Related papers

Single-photon detectors for practical quantum cryptography

Alberto Tosi, Franco Zappa, S. Cova

The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 19, 2012•15 citations

High-Speed Free-Space QKD in the Presence of SPAD Dead Time

Shuangfeng Jiang, Majid Safari

Recently, there has been growing research interest in quantum technology in general and particularly in quantum key distribution (QKD) that enables two legitimate parties to share a secret key without leaking information to third parties. Practical implementation of QKD has shown limited key rates due to the practical limits of quantum sources and detectors. For example, after each detection event, practical single-photon detectors such as single-photon avalanche diodes (SPADs) undergo a period of inactivity called dead time, which limits the highest photon transmission rate achievable for QKD systems as photon transmission at sub-dead-time regime can generate security loopholes. In this paper, we analyze the performance of a sifting scheme that allows for high-speed operation at sub-dead-time regime both theoretically and numerically. We consider an FSO QKD system, where the effect of background noise can be significant and derive the expressions of sifting probability and sifted bit rate considering both dead time and background noise effects. We present a comprehensive performance analysis of the QKD system in terms of quantum bit error rate (QBER) and secrecy key rate (SKR) and show that operation at sub-dead-time regime can significantly improve the achievable SKR for FSO systems with certain path loss and background noise levels.

IEEE International Conference on Communications workshops•May 16, 2022•7 citations

Spurious Pulse Detection in Fibre-Optic Channels Using Measurement-Device-Independent Quantum Key Distribution with Single-Photon Avalanche Photodiodes

J. Suneetha, Smita Darandale

Abstract The safe exchange of cryptographic keys is made possible by Quantum Key Distribution (QKD), which makes use of the basic ideas of quantum physics. Quantum Bit Error Rate (QBER), key generation rate, and transmission distance are important performance measures in QKD systems. Nevertheless, undesired noise sources that impair system performance, such dark counts and afterpulses, restrict traditional QKD implementations. The Measurement-Device-Independent QKD (MDI-QKD) protocol and Single Photon Avalanche Diodes (SPADs) for single-photon detection are combined in this research to create an improved QKD model. All detector-side-channel weaknesses are naturally eliminated by the MDI-QKD protocol, while SPADs' excellent sensitivity and temporal precision allow for precise noise source detection and characterisation, including dark count and afterpulse rates. When compared to conventional QKD systems, the suggested method performs better when assessed using QBER. According to experimental findings, including SPADs into the MDI-QKD architecture greatly improves the security and effectiveness of quantum communication systems by detecting detector-induced errors.

•Mar 12, 2026•0 citations

SUPERTWIN: towards 100kpixel CMOS quantum image sensors for quantum optics applications

Leonardo Gasparini, Bänz Bessire, Manuel Unternährer +4 more

Quantum imaging uses entangled photons to overcome the limits of a classical-light apparatus in terms of image quality, beating the standard shot-noise limit, and exceeding the Abbe diffraction limit for resolution. In today experiments, the spatial properties of entangled photons are recorded by means of complex and slow setups that include either the motorized scanning of single-pixel single-photon detectors, such as Photo-Multiplier Tubes (PMT) or Silicon Photo- Multipliers (SiPM), or the use of low frame rate intensified CCD cameras. CMOS arrays of Single Photon Avalanche Diodes (SPAD) represent a relatively recent technology that may lead to simpler setups and faster acquisition. They are spatially- and time-resolved single-photon detectors, i.e. they can provide the position within the array and the time of arrival of every detected photon with <100 ps resolution. SUPERTWIN is a European H2020 project aiming at developing the technological building blocks (emitter, detector and system) for a new, all solid-state quantum microscope system exploiting entangled photons to overcome the Rayleigh limit, targeting a resolution of 40nm. This work provides the measurement results of the 2nd order cross-correlation function relative to a flux of entangled photon pairs acquired with a fully digital 8×16 pixel SPAD array in CMOS technology. The limitations for application in quantum optics of the employed architecture and of other solutions in the literature will be analyzed, with emphasis on crosstalk. Then, the specifications for a dedicated detector will be given, paving the way for future implementations of 100kpixel Quantum Image Sensors.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jan 27, 2017•21 citations

High Count-Rate 8 × 8 SPAD Arrays for Quantum Key Distribution

Caterina Garofalo, M. Raimondi, Kevin Herrera Andres Pesantes +3 more

We developed a SPAD detector implementing an array structure to achieve short deadtime and high detection efficiency, to be employed in ground-based optical receivers for enhancing key rates in Quantum Key Distribution (QKD) channels at 800 nm. The device detects over 2 billion photons per second, thus enabling transmission rates beyond 2 GHz. The detector features two 8 × 8 SPAD arrays, named Trial A and Trial B, sharing 4 outputs. Trial A combines its 64 SPADs’ outputs in an OR-tree connected to a frequency divider, distributing the pulses to the 4 outputs. Trial B has 4 independent quadrants, each with its own OR-tree feeding a toggle flip-flop and connected to a single output. A pulse shrinker reduces the pile-up effect. The detector exhibits a Photon Detection Efficiency (PDE) of 39.6% at 800 nm, a median Dark Count Rate (DCR) of 300 cps/pixel, afterpulsing probability below 0.1% and a 230 ps Full-Width at Half-Maximum (FWHM) jitter per SPAD.

•Jan 1, 2026•0 citations

High-Speed Quantum Key Distribution Using Dead-Time Compensated Detector Arrays

Shuangfeng Jiang, Majid Safari

There has been growing research interest in quantum technology in general and in quantum key distribution (QKD) in particular. However, the key generation rate of QKD systems is still limited by the quantum channel losses as well as the practical limitations of the quantum sources and detectors. Here, we focus on one of these limitations, namely, the quantum detector's dead time effect, which happens after each photon detection, limiting the maximum quantum bit transmission rate and consequently the key generation rate of QKD systems. Qubit transmission at the sub-dead-time regime (i.e., faster than the reciprocal of dead time) can introduce different security loopholes. In this paper, we propose the use of a detector array instead of a single detector to measure the quantum state of individual photons in discrete variable QKD systems, showing that it can significantly alleviate the limitations induced by detectors' dead time. A dead-time compensated BB84 scheme is introduced, allowing qubit transmission at the sub-dead-time regime. An$M-$dimensional Markov chain model is used to describe the impact of dead time on the operation of the proposed BB84 system, employing detector arrays of size$M$. Consequently, novel analytical expressions can be derived for the sifted bit rate (SBR) and secrecy key rate (SKR) of the proposed QKD system, showing excellent match with the Monte Carlo simulation results. A remarkable gain is observed for the BB84 system employing detector arrays, showing a potential$M$-fold improvement of SBR at high qubit transmission rates.

Journal of Lightwave Technology•Feb 7, 2024•5 citations
The deployment of Discrete Variable Quantum Key Distribution (DV-QKD) in high-traffic, short-reach environments, such as intra-data center networks, is currently constrained by the saturation of single-photon detectors. While CMOS Single-Photon Avalanche Diodes (SPADs) offer a cost-effective solution, their Secure Key Rate (SKR) is limited by detector dead time. To the best of the authors' knowledge, this work is the first to derive a generalized detection rate model for SiPMs that addresses the dead-time bottlenecks of gigahertz-rate quantum cryptography. While methods for managing deadtime via active optical switching have been proposed, our model quantifies the benefits of passive spatial multiplexing inherent in standard SiPM arrays. Furthermore, contrasting with models designed to optimize energy resolution or characterize nonlinear charge response to light pulses, our work focuses on maximizing the detection count rate. We derive exact detection rate models for both analog (paralyzable) and digital (non-paralyzable) SiPM architectures, incorporating correlated noise sources such as optical crosstalk and afterpulsing. Simulation results indicate that SiPMs can increase detection rates by over an order of magnitude compared to single SPADs.
The implementation and commercialization of quantum cryptography technologies have to face some challenges related to the development of single-photon detectors operating at 1550 nm. The main requirements are: i) high detection efficiency; ii) low noise; iii) high count rate; iv) low timing jitter. Different technologies are currently available for single-photon detection at 1550 nm, but semiconductor devices (like Single-Photon Avalanche Diode, SPAD) offer a photon detection efficiency that is inherently higher than any photocathode employed in vacuum tube detectors. Additionally InGaAs/InP SPADs can detect single photons at 1550 nm with low noise when moderately cooled by means of thermo-electric coolers. Consequently, InGaAs/InP SPAD can be the enabling technology of practical quantum key distribution (QKD) systems, provided that the maximum count rate is increased above 1 Mcps. The main limit is the afterpulsing effect that usually sets too long (< 10 μs) a hold-off time after each avalanche ignition. We present the developments achieved in InGaAs/InP SPAD device design, fabrication technology and front-end electronics, aimed at decreasing the afterpulsing effect, while not impairing photon detection efficiency and timing jitter. The new InGaAs/InP SPADs provide count rates higher than 1 Mcps and temporal response with 60 ps Full-Width at Half Maximum and very short (30 ps time constant) tail. The front-end electronics includes a wide-band pulse generator able to gate the SPAD up to 133 MHz repetition rate. Eventually, a fast avalanche-quenching scheme minimizes quenching time to less than 1 ns, thus effectively reducing afterpulsing by decreasing the total charge flowing through the junction.
Recently, there has been growing research interest in quantum technology in general and particularly in quantum key distribution (QKD) that enables two legitimate parties to share a secret key without leaking information to third parties. Practical implementation of QKD has shown limited key rates due to the practical limits of quantum sources and detectors. For example, after each detection event, practical single-photon detectors such as single-photon avalanche diodes (SPADs) undergo a period of inactivity called dead time, which limits the highest photon transmission rate achievable for QKD systems as photon transmission at sub-dead-time regime can generate security loopholes. In this paper, we analyze the performance of a sifting scheme that allows for high-speed operation at sub-dead-time regime both theoretically and numerically. We consider an FSO QKD system, where the effect of background noise can be significant and derive the expressions of sifting probability and sifted bit rate considering both dead time and background noise effects. We present a comprehensive performance analysis of the QKD system in terms of quantum bit error rate (QBER) and secrecy key rate (SKR) and show that operation at sub-dead-time regime can significantly improve the achievable SKR for FSO systems with certain path loss and background noise levels.
Abstract The safe exchange of cryptographic keys is made possible by Quantum Key Distribution (QKD), which makes use of the basic ideas of quantum physics. Quantum Bit Error Rate (QBER), key generation rate, and transmission distance are important performance measures in QKD systems. Nevertheless, undesired noise sources that impair system performance, such dark counts and afterpulses, restrict traditional QKD implementations. The Measurement-Device-Independent QKD (MDI-QKD) protocol and Single Photon Avalanche Diodes (SPADs) for single-photon detection are combined in this research to create an improved QKD model. All detector-side-channel weaknesses are naturally eliminated by the MDI-QKD protocol, while SPADs' excellent sensitivity and temporal precision allow for precise noise source detection and characterisation, including dark count and afterpulse rates. When compared to conventional QKD systems, the suggested method performs better when assessed using QBER. According to experimental findings, including SPADs into the MDI-QKD architecture greatly improves the security and effectiveness of quantum communication systems by detecting detector-induced errors.
Quantum imaging uses entangled photons to overcome the limits of a classical-light apparatus in terms of image quality, beating the standard shot-noise limit, and exceeding the Abbe diffraction limit for resolution. In today experiments, the spatial properties of entangled photons are recorded by means of complex and slow setups that include either the motorized scanning of single-pixel single-photon detectors, such as Photo-Multiplier Tubes (PMT) or Silicon Photo- Multipliers (SiPM), or the use of low frame rate intensified CCD cameras. CMOS arrays of Single Photon Avalanche Diodes (SPAD) represent a relatively recent technology that may lead to simpler setups and faster acquisition. They are spatially- and time-resolved single-photon detectors, i.e. they can provide the position within the array and the time of arrival of every detected photon with <100 ps resolution. SUPERTWIN is a European H2020 project aiming at developing the technological building blocks (emitter, detector and system) for a new, all solid-state quantum microscope system exploiting entangled photons to overcome the Rayleigh limit, targeting a resolution of 40nm. This work provides the measurement results of the 2nd order cross-correlation function relative to a flux of entangled photon pairs acquired with a fully digital 8×16 pixel SPAD array in CMOS technology. The limitations for application in quantum optics of the employed architecture and of other solutions in the literature will be analyzed, with emphasis on crosstalk. Then, the specifications for a dedicated detector will be given, paving the way for future implementations of 100kpixel Quantum Image Sensors.
We developed a SPAD detector implementing an array structure to achieve short deadtime and high detection efficiency, to be employed in ground-based optical receivers for enhancing key rates in Quantum Key Distribution (QKD) channels at 800 nm. The device detects over 2 billion photons per second, thus enabling transmission rates beyond 2 GHz. The detector features two 8 × 8 SPAD arrays, named Trial A and Trial B, sharing 4 outputs. Trial A combines its 64 SPADs’ outputs in an OR-tree connected to a frequency divider, distributing the pulses to the 4 outputs. Trial B has 4 independent quadrants, each with its own OR-tree feeding a toggle flip-flop and connected to a single output. A pulse shrinker reduces the pile-up effect. The detector exhibits a Photon Detection Efficiency (PDE) of 39.6% at 800 nm, a median Dark Count Rate (DCR) of 300 cps/pixel, afterpulsing probability below 0.1% and a 230 ps Full-Width at Half-Maximum (FWHM) jitter per SPAD.
There has been growing research interest in quantum technology in general and in quantum key distribution (QKD) in particular. However, the key generation rate of QKD systems is still limited by the quantum channel losses as well as the practical limitations of the quantum sources and detectors. Here, we focus on one of these limitations, namely, the quantum detector's dead time effect, which happens after each photon detection, limiting the maximum quantum bit transmission rate and consequently the key generation rate of QKD systems. Qubit transmission at the sub-dead-time regime (i.e., faster than the reciprocal of dead time) can introduce different security loopholes. In this paper, we propose the use of a detector array instead of a single detector to measure the quantum state of individual photons in discrete variable QKD systems, showing that it can significantly alleviate the limitations induced by detectors' dead time. A dead-time compensated BB84 scheme is introduced, allowing qubit transmission at the sub-dead-time regime. AnM−M-M−dimensional Markov chain model is used to describe the impact of dead time on the operation of the proposed BB84 system, employing detector arrays of sizeMMM. Consequently, novel analytical expressions can be derived for the sifted bit rate (SBR) and secrecy key rate (SKR) of the proposed QKD system, showing excellent match with the Monte Carlo simulation results. A remarkable gain is observed for the BB84 system employing detector arrays, showing a potentialMMM-fold improvement of SBR at high qubit transmission rates.