Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Elmas içerisinde renk merkezleri oluşturularak kuantum emiterlerin üretilmesi

Şentürk Irmak, Sevil Berrak

Published Apr 14, 2025• 0 citations
OpenAlex

Abstract

This thesis explores the generation of nitrogen-vacancy (NV) color centers in diamond, which are solid-state quantum emitters. Quantum emitters are critical for applications in quantum cryptography, sensing, and computing. Due to their stable photoluminescence and long spin coherence times at room temperature, NV centers are particularly worthy of studying in quantum technologies. The study aims to produce NV centers in a controlled manner by using low-energy electron beam irradiation and thermal annealing. The experimental method began with the selection of a nitrogen doped high-pressure high-temperature (HPHT) synthesized type Ib single-crystal plate diamond with a {100} surface orientation, obtained from Element Six. Electron irradiation was carried out using a lithography system at 100 keV with varying doses (0.5–5.0 C/cm²) applied in specific patterns on four corners of this sample. This step aimed to introduce vacancies in a spatially resolved manner. Subsequent annealing at 800 °C under argon flow at 100 CCM was done to induce the migration of these vacancies to nearby substitutional nitrogen atoms. These processes combined lead to the formation of NV centers. A comprehensive characterization process was conducted at each stage using topographical imaging with an optical profilometer, Raman spectroscopy, photoluminescence (PL) spectroscopy, and electron spin resonance (ESR). Raman analysis confirmed the integrity of the diamond lattice post-treatment. It also provided insights into strain–stress relations within the diamond lattice. Shifts in the diamond Raman peak position and changes in full width at half maximum (FWHM) across the sample revealed localized lattice stress. This discovery was important because these stress variations directly influence NV center formation and performance. PL spectroscopy detected distinct zero-phonon line (ZPL) emissions at ~638 nm, indicative of negatively charged NV⁻ centers. The intensity of NV⁻ emission was observed to vary with electron dose, which indicates the ability to control NV center density. Mapping of the PL signal further demonstrated successful spatial control of NVs on the sample. ESR measurements confirmed the spin-related properties of the generated centers and the charge state transition from NV⁰ to NV⁻ following annealing. Overall, this work stands out for its use of low-energy electron irradiation which is preferable due to easier control over defect positioning and potentially lower damage to the host lattice. This thesis contributes to the development of deterministic NV center engineering.

Related papers

Photoluminescence characterization of NV centers in CVD diamond as a function of different nitrogen doping levels for quantum sensing applications

Sierra Gómez, Javier, Silva Neto, José Vieira da, Trava Airoldi, Vladimir Jesus +1 more

Nitrogen-vacancy (NV) centers in single-crystal CVD diamond are promising candidates for quantum sensing due to their remarkable optical and spin properties [1]. These defects exhibit stable photoluminescence (PL), long spin coherence times, and high sensitivity to external fields [2]. In this study, we present a room-temperature PL characterization of NV centers excited with a 532 nm laser. The setup was optimized for high signal-to-noise ratio and spectral resolution. Key parameters analyzed include emission intensity, zero-phonon line (ZPL) at ~637 nm, phonon sidebands, and the charge state distribution between NV⁰ and NV⁻. The NV⁻ state, crucial for spin-based sensing, is evaluated to understand its stability under different nitrogen doping conditions [3]. The relative intensities of NV⁰ and NV⁻ provide insights into nitrogen incorporation and vacancy formation. These results contribute to optimizing synthesis conditions for enhanced NV⁻ concentration, supporting the advancement of diamond-based quantum sensing technologies.

•Jan 1, 2025•0 citations

Optical and Spin Properties of NV Center Ensembles in Diamond Nano-Pillars

Kseniia Volkova, Julia Heupel, Sergei D. Trofimov +10 more

Nitrogen-vacancy (NV) color centers in diamond are excellent quantum sensors possessing high sensitivity and nano-scale spatial resolution. Their integration in photonic structures is often desired, since it leads to an increased photon emission and also allows the realization of solid-state quantum technology architectures. Here, we report the fabrication of diamond nano-pillars with diameters up to 1000 nm by electron beam lithography and inductively coupled plasma reactive ion etching in nitrogen-rich diamonds (type Ib) with [100] and [111] crystal orientations. The NV centers were created by keV-He ion bombardment and subsequent annealing, and we estimate an average number of NVs per pillar to be 4300 ± 300 and 520 ± 120 for the [100] and [111] samples, respectively. Lifetime measurements of the NVs’ excited state showed two time constants with average values of τ1 ≈ 2 ns and τ2 ≈ 8 ns, which are shorter as compared to a single color center in a bulk crystal (τ ≈ 10 ns). This is probably due to a coupling between the NVs as well as due to interaction with bombardment-induced defects and substitutional nitrogen (P1 centers). Optically detected magnetic resonance measurements revealed a contrast of about 5% and average coherence and relaxation times of T2 [100] = 420 ± 40 ns, T2 [111] = 560 ± 50 ns, and T1 [100] = 162 ± 11 μs, T1 [111] = 174 ± 24 μs. These pillars could find an application for scanning probe magnetic field imaging.

Nanomaterials•Apr 29, 2022•24 citations

Effects of Electron Irradiation and Anneal Condition on Creation of Nitrogen-Vacancy Centers in Ib Diamonds

Ishii Shuya, Onoda Shinobu, Abe Hiroshi +1 more

Electron irradiation is one of the most powerful methods to create negatively charged nitrogen-vacancy centers (NV-s) in diamonds, which act as qubits and quantum sensors even at room temperature (RT). For quantum sensing, it is important to create ensemble NV-s with long coherence time (T2) since the sensitivity can be affected by both amount of NV- and T2. For high concentration NV-, electron irradiation with higher fluence is needed. However, if electron fluence is too high, neutral NVs (NV0s) are created because of lack of N donors. For T2, since residual defects act as origins of T2 decoherence, it is important to optimize the condition of subsequent annealing as well as irradiation fluence. Thus, we need to consider initial nitrogen (P1) concentration in diamond, electron fluence, and annealing conditions. In this paper, we create NV-s in Ib diamonds by electron irradiation and subsequent annealing with different conditions, and study the amounts of NV-s and their T2 for high-sensitive quantum sensing. The samples used in this study were Ib diamond with P1 concentration around 100 ppm. Those samples were irradiated with 2 MeV-electrons at a fluence of 1x1018/cm2 at RT. After irradiation, the samples were annealed between 600 and 1400oC in Ar. Photoluminescence (PL) measurements were carried out at RT to confirm NV creation. For PL measurements, the laser with a wavelength of 532 nm was used as excitation. PL intensity for samples annealed at 600 oC is about half even after annealing for 600 min, comparing with that for 800 oC-annealed samples although the values increase with increasing annealing time. Thus, the annealing at 650 oC is not enough to create NV. The samples annealed between 800 and 1200 oC show the highest PL intensity even after annealing for 10 min. The 800 and 1000 oC-annealed samples keep the PL intensity after annealing for 1200 min although the PL intensity for 1200 oC-annealed samples decrease with increasing annealing time above 100 min. The PL intensity for the samples annealed at 1400 oC shows smaller value and decreases with increasing annealing time. For T2, the samples annealed at 1400 oC show 2 microsec after annealing for 10 min. However, NV- cannot be observed after annealing at 1400 oC for 30min. Therefore, it can be concluded that annealing at 1400 oC is not suitable for the creation of NV-. For samples annealed between 600 and 1000 oC, the values of T2 are constant (between 0.5 and 0.9 microsec) after annealing up to 1200 min. For samples annealed at 1200 oC, no significant difference in T2 value is observed from those annealed between 600 and 1000 oC up to 30min, and the value increases with increasing annealing time above 30 min. From the point of view of sensing, it is important to consider both the amounts of NV- centers and T2. Therefore, we compare the values of PL intensity times T2. As a result, the samples annealed between 800 and 1200 oC show the highest value although the value for samples annealed at 1200 oC decreases after annealing for 1200 min. This suggests that annealing at 800 oC for 10 min is enough to create NV-s. We also study the creation of NV-s in diamonds by electron irradiation at elevated temperature. The samples with P1 concentration around 60 and 100 ppm were irradiated with 2 MeV-electrons at fluences up to 5x1018/cm2 at 800 or 1000 oC. The samples were annealed at 1000 oC for 120 min after irradiation. The amounts of NV are estimated from electron spin resonance (ESR) signals. As a result, samples irradiated at 800 and 1000 oC show higher NV- concentration than that for RT-irradiated ones, and 800 oC-irradiated ones show higher NV concentration than 1000oC-irradiated ones. Since the T2 values are not affected by irradiation temperature, the elevated temperature irradiation, especially 800 oC irradiation is a useful method to realize quantum sensing with high sensitivity.

•Jul 10, 2025•0 citations

Engineering of Color Centers in Isotopically Purified Diamond for Quantum Technologies

Christoph Findler

Silicon has turned from a niche laboratory-scale material into the backbone of modern electronics. Diamond functionalized with color centers could follow a similar path and grow from proof-of-concepts experiments to application-oriented quantum technologies. Quantum sensing, communication, and information processing with color centers has been proven to work in scientific experiments and enhanced sensitivities as well as novel functionalities have been reported. While the first generation of diamond quantum devices relied on color centers formed uncontrolled in natural diamond with a high statistical variation in composition and crystallinity, the situation has changed nowadays. With the emergence of high purity monocrystals and the option for isotopic purification of the carbon matrix, technological progress in materials science on the atomic-scale enabled tailoring the spin properties in diamond. But, since many color centers typically require vacancies to combine with impurities in the carbon lattice via diffusion, the generation of color centers underlies a statistical process providing only little control on the center's final position in the crystal lattice. The negatively charged nitrogen-vacancy (NV$^-$) center is the most studied optically active defect in diamond and exhibits remarkable spin properties and sensing capabilities, even on the nanoscale and at room temperature. The spin properties of NV$^-$ centers close to the surface (1\,nm - 30\,nm) have been thoroughly studied and the deeper the spins are located in diamond the less decoherence from surface defects is observed. Creating NV$^-$ centers at the surface by nitrogen ion implantation and burying them beneath a thin diamond layer via chemical vapor deposition (CVD) of diamond is reported to enhance the coherence times significantly. By separating the color center generation from controlling the resulting depth by an additional diamond layer, narrow depth profiles can be achieved by reducing the ion energy during implantation. Although the coherence properties improve, many of the implanted NV$^-$ center are reported to vanish in the hydrogen-rich plasma of growth CVD chambers. The mechanism responsible for the instability of NV$^-$ centers towards the plasma remains unclear, though. One hypothesis is the formation of nitrogen-vacancy-hydrogen centers from diffusing hydrogen and implanted NV$^-$ centers but is has not been proven, yet. Here, we demonstrate the fabrication of depth confined NV$^-$ centers by combining low energy (1\,keV - 5\,keV) ion implantation and CVD overgrowth. By increasing the thickness of the overgrown layer (6\,nm - 100\,nm) the influence of surface noise is shown to decrease leading to bulk-like coherence properties of up to $450\,\upmu$s (Hahn-echo) and $T_2^*$ dephasing times around $20\,\upmu$s. Monitoring the NV$^-$ density as a function of the overgrowth time, we analyze the kinetics of the passivation in case of implanting ion doses of 10$^{11}$ $^{15}$N $^{+}$/cm$^2$ and 10$^{12}$ $^{15}$N $^{+}$/cm$^2$. The passivation turns out to occur faster for lower doses offering insights into sub-surface hydrogen diffusion in diamond. Analyzing the spin bath before and after overgrowth reveals a drastic reduction in paramagnetic spins after the CVD process but no NVH$^-$ is found around the surviving NV$^-$ centers. Checking the chemical composition in overgrown implantation sites with secondary-ion-mass-specrometry (SIMS), however, confirms significant amounts of hydrogen in the $^{15}$N-implanted layers. Since the concentration found for hydrogen exceeds the one for nitrogen by far, we suggest that diffusing hydrogen interacts also with vacancies forming probably mostly diamagnetic defects. In the last part of this dissertation, NV$^-$ centers are generated with sub-nanometer precision below a thin $^{13}$C-enriched layer for quantum simulation. For fabricating the spin architecture starting from a $^{12}$C base layer, we overgrow implanted nitrogen with a $^{13}$C layer and bury the spins beneath a 30\,nm-thick $^{12}$C capping layer. By measuring the coupling strength between the electron and nuclear spins, we deduce a NV$^-$ placement accuracy reaching below one nanometer with respect to the $^{13}$C-layer. Regarding the spin properties of the electron spins, no reduction in $T_2$ is observed despite of the proximity to the dense $^{13}$C-bath. As a consequence, the overgrowth of NV$^-$ centers is demonstrated as a bottom-up approach to produce buried spin architectures with sharp isotopic transitions and efficient $^{13}$C-NV$^-$ coupling. Together with the potential for bulk-like coherence properties the synergy of implantation and overgrowth is a powerful tool to fabricate reproducible quantum systems with tailored properties and high depth confinement.

•Jan 1, 2026•0 citations

Engineering of nitrogen-vacancy color centers in high purity diamond by ion implantation and annealing

Julius O. Orwa, Charles Santori, Kai‐Mei C. Fu +11 more

The negatively-charged nitrogen-vacancy (NV) center is the most studied optical center in diamond and is very important for applications in quantum information science. Many proposals for integrating NV centers in quantum and sensing applications rely on their tailored fabrication in ultra pure host material. In this study, we use ion implantation to controllably introduce nitrogen into high purity, low nitrogen chemical vapor deposition diamond samples. The properties of the resulting NV centers are studied as a function of implantation temperature, annealing temperature, and implantation fluence. We compare the implanted NV centers with native NV centers present deep in the bulk of the as-grown samples. The results for implanted NV centers are promising but indicate, at this stage, that the deep native NV centers possess overall superior optical properties. In particular, the implanted NV centers obtained after annealing at 2000 °C under a stabilizing pressure of 8 GPa showed an ensemble linewidth of 0.17 nm compared to 0.61 nm after annealing at 1000 °C. Over the same temperature range, the ensemble NV−/NV0 ratio increased by a factor of ∼5, although this was accompanied by an overall decrease in the NV count.

Journal of Applied Physics•Apr 15, 2011•126 citations

Characterization and optimization of NV centers in CVD diamond for sensing applications

Tingpeng Luo, Lukas Lindner, Julia Langer +13 more

The negatively charged nitrogen-vacancy (NV-) center in diamond is a promising spin system for quantum sensing applications. NV-ensembles are favored for an improved signal-to-noise ratio and sensitivity. The optimization of diamond with NV-ensembles often requires a high NV concentration, a long spin coherence time T2 and a stable charge state. However, these key requirements are interdependent and can be difficult to optimize: nitrogen impurities as the main decoherence source of the NV spin limits the coherence time T2, and pursuing high NV concentration can deteriorate the NV-charge-state stability. Consequently, their best achievable combination becomes an essential question for the material characterization. In this work, we systematically investigate the NV center creation and properties in chemical vapor deposition (CVD) diamond. We have grown CVD diamond series with a varying nitrogen flow over four orders of magnitude, leading to a broad range of single substitutional nitrogen (P1 center) densities from 0.2 to 20 ppm. On these series, we study P1, NV creations and NV charge states after growth, as well as their transformation under subsequent electron beam irradiation. Furthermore, for a fixed nitrogen concentration, we optimize electron-irradiation fluences with two different accelerated electron energies. We discuss a general approach to determine the optimal irradiation conditions, for which an enhanced NV concentration and an optimum of NV charge states can both be satisfied. Moreover, through irradiation and annealing treatments, we monitor the change in T2 and aim to increase the NV density without compromising T2. We achieve NV concentrations from 1 to 168 ppb with T2 from 549 to 45.5 µs respectively. This study shows a pathway to engineer properties of NV-doped CVD diamonds for improved sensitivity.

•Jun 8, 2022•0 citations
This thesis explores the generation of nitrogen-vacancy (NV) color centers in diamond, which are solid-state quantum emitters. Quantum emitters are critical for applications in quantum cryptography, sensing, and computing. Due to their stable photoluminescence and long spin coherence times at room temperature, NV centers are particularly worthy of studying in quantum technologies. The study aims to produce NV centers in a controlled manner by using low-energy electron beam irradiation and thermal annealing. The experimental method began with the selection of a nitrogen doped high-pressure high-temperature (HPHT) synthesized type Ib single-crystal plate diamond with a {100} surface orientation, obtained from Element Six. Electron irradiation was carried out using a lithography system at 100 keV with varying doses (0.5–5.0 C/cm²) applied in specific patterns on four corners of this sample. This step aimed to introduce vacancies in a spatially resolved manner. Subsequent annealing at 800 °C under argon flow at 100 CCM was done to induce the migration of these vacancies to nearby substitutional nitrogen atoms. These processes combined lead to the formation of NV centers. A comprehensive characterization process was conducted at each stage using topographical imaging with an optical profilometer, Raman spectroscopy, photoluminescence (PL) spectroscopy, and electron spin resonance (ESR). Raman analysis confirmed the integrity of the diamond lattice post-treatment. It also provided insights into strain–stress relations within the diamond lattice. Shifts in the diamond Raman peak position and changes in full width at half maximum (FWHM) across the sample revealed localized lattice stress. This discovery was important because these stress variations directly influence NV center formation and performance. PL spectroscopy detected distinct zero-phonon line (ZPL) emissions at ~638 nm, indicative of negatively charged NV⁻ centers. The intensity of NV⁻ emission was observed to vary with electron dose, which indicates the ability to control NV center density. Mapping of the PL signal further demonstrated successful spatial control of NVs on the sample. ESR measurements confirmed the spin-related properties of the generated centers and the charge state transition from NV⁰ to NV⁻ following annealing. Overall, this work stands out for its use of low-energy electron irradiation which is preferable due to easier control over defect positioning and potentially lower damage to the host lattice. This thesis contributes to the development of deterministic NV center engineering.
Nitrogen-vacancy (NV) centers in single-crystal CVD diamond are promising candidates for quantum sensing due to their remarkable optical and spin properties [1]. These defects exhibit stable photoluminescence (PL), long spin coherence times, and high sensitivity to external fields [2]. In this study, we present a room-temperature PL characterization of NV centers excited with a 532 nm laser. The setup was optimized for high signal-to-noise ratio and spectral resolution. Key parameters analyzed include emission intensity, zero-phonon line (ZPL) at ~637 nm, phonon sidebands, and the charge state distribution between NV⁰ and NV⁻. The NV⁻ state, crucial for spin-based sensing, is evaluated to understand its stability under different nitrogen doping conditions [3]. The relative intensities of NV⁰ and NV⁻ provide insights into nitrogen incorporation and vacancy formation. These results contribute to optimizing synthesis conditions for enhanced NV⁻ concentration, supporting the advancement of diamond-based quantum sensing technologies.
Nitrogen-vacancy (NV) color centers in diamond are excellent quantum sensors possessing high sensitivity and nano-scale spatial resolution. Their integration in photonic structures is often desired, since it leads to an increased photon emission and also allows the realization of solid-state quantum technology architectures. Here, we report the fabrication of diamond nano-pillars with diameters up to 1000 nm by electron beam lithography and inductively coupled plasma reactive ion etching in nitrogen-rich diamonds (type Ib) with [100] and [111] crystal orientations. The NV centers were created by keV-He ion bombardment and subsequent annealing, and we estimate an average number of NVs per pillar to be 4300 ± 300 and 520 ± 120 for the [100] and [111] samples, respectively. Lifetime measurements of the NVs’ excited state showed two time constants with average values of τ1 ≈ 2 ns and τ2 ≈ 8 ns, which are shorter as compared to a single color center in a bulk crystal (τ ≈ 10 ns). This is probably due to a coupling between the NVs as well as due to interaction with bombardment-induced defects and substitutional nitrogen (P1 centers). Optically detected magnetic resonance measurements revealed a contrast of about 5% and average coherence and relaxation times of T2 [100] = 420 ± 40 ns, T2 [111] = 560 ± 50 ns, and T1 [100] = 162 ± 11 μs, T1 [111] = 174 ± 24 μs. These pillars could find an application for scanning probe magnetic field imaging.
Electron irradiation is one of the most powerful methods to create negatively charged nitrogen-vacancy centers (NV-s) in diamonds, which act as qubits and quantum sensors even at room temperature (RT). For quantum sensing, it is important to create ensemble NV-s with long coherence time (T2) since the sensitivity can be affected by both amount of NV- and T2. For high concentration NV-, electron irradiation with higher fluence is needed. However, if electron fluence is too high, neutral NVs (NV0s) are created because of lack of N donors. For T2, since residual defects act as origins of T2 decoherence, it is important to optimize the condition of subsequent annealing as well as irradiation fluence. Thus, we need to consider initial nitrogen (P1) concentration in diamond, electron fluence, and annealing conditions. In this paper, we create NV-s in Ib diamonds by electron irradiation and subsequent annealing with different conditions, and study the amounts of NV-s and their T2 for high-sensitive quantum sensing. The samples used in this study were Ib diamond with P1 concentration around 100 ppm. Those samples were irradiated with 2 MeV-electrons at a fluence of 1x1018/cm2 at RT. After irradiation, the samples were annealed between 600 and 1400oC in Ar. Photoluminescence (PL) measurements were carried out at RT to confirm NV creation. For PL measurements, the laser with a wavelength of 532 nm was used as excitation. PL intensity for samples annealed at 600 oC is about half even after annealing for 600 min, comparing with that for 800 oC-annealed samples although the values increase with increasing annealing time. Thus, the annealing at 650 oC is not enough to create NV. The samples annealed between 800 and 1200 oC show the highest PL intensity even after annealing for 10 min. The 800 and 1000 oC-annealed samples keep the PL intensity after annealing for 1200 min although the PL intensity for 1200 oC-annealed samples decrease with increasing annealing time above 100 min. The PL intensity for the samples annealed at 1400 oC shows smaller value and decreases with increasing annealing time. For T2, the samples annealed at 1400 oC show 2 microsec after annealing for 10 min. However, NV- cannot be observed after annealing at 1400 oC for 30min. Therefore, it can be concluded that annealing at 1400 oC is not suitable for the creation of NV-. For samples annealed between 600 and 1000 oC, the values of T2 are constant (between 0.5 and 0.9 microsec) after annealing up to 1200 min. For samples annealed at 1200 oC, no significant difference in T2 value is observed from those annealed between 600 and 1000 oC up to 30min, and the value increases with increasing annealing time above 30 min. From the point of view of sensing, it is important to consider both the amounts of NV- centers and T2. Therefore, we compare the values of PL intensity times T2. As a result, the samples annealed between 800 and 1200 oC show the highest value although the value for samples annealed at 1200 oC decreases after annealing for 1200 min. This suggests that annealing at 800 oC for 10 min is enough to create NV-s. We also study the creation of NV-s in diamonds by electron irradiation at elevated temperature. The samples with P1 concentration around 60 and 100 ppm were irradiated with 2 MeV-electrons at fluences up to 5x1018/cm2 at 800 or 1000 oC. The samples were annealed at 1000 oC for 120 min after irradiation. The amounts of NV are estimated from electron spin resonance (ESR) signals. As a result, samples irradiated at 800 and 1000 oC show higher NV- concentration than that for RT-irradiated ones, and 800 oC-irradiated ones show higher NV concentration than 1000oC-irradiated ones. Since the T2 values are not affected by irradiation temperature, the elevated temperature irradiation, especially 800 oC irradiation is a useful method to realize quantum sensing with high sensitivity.
Silicon has turned from a niche laboratory-scale material into the backbone of modern electronics. Diamond functionalized with color centers could follow a similar path and grow from proof-of-concepts experiments to application-oriented quantum technologies. Quantum sensing, communication, and information processing with color centers has been proven to work in scientific experiments and enhanced sensitivities as well as novel functionalities have been reported. While the first generation of diamond quantum devices relied on color centers formed uncontrolled in natural diamond with a high statistical variation in composition and crystallinity, the situation has changed nowadays. With the emergence of high purity monocrystals and the option for isotopic purification of the carbon matrix, technological progress in materials science on the atomic-scale enabled tailoring the spin properties in diamond. But, since many color centers typically require vacancies to combine with impurities in the carbon lattice via diffusion, the generation of color centers underlies a statistical process providing only little control on the center's final position in the crystal lattice. The negatively charged nitrogen-vacancy (NV−^-−) center is the most studied optically active defect in diamond and exhibits remarkable spin properties and sensing capabilities, even on the nanoscale and at room temperature. The spin properties of NV−^-− centers close to the surface (1\,nm - 30\,nm) have been thoroughly studied and the deeper the spins are located in diamond the less decoherence from surface defects is observed. Creating NV−^-− centers at the surface by nitrogen ion implantation and burying them beneath a thin diamond layer via chemical vapor deposition (CVD) of diamond is reported to enhance the coherence times significantly. By separating the color center generation from controlling the resulting depth by an additional diamond layer, narrow depth profiles can be achieved by reducing the ion energy during implantation. Although the coherence properties improve, many of the implanted NV−^-− center are reported to vanish in the hydrogen-rich plasma of growth CVD chambers. The mechanism responsible for the instability of NV−^-− centers towards the plasma remains unclear, though. One hypothesis is the formation of nitrogen-vacancy-hydrogen centers from diffusing hydrogen and implanted NV−^-− centers but is has not been proven, yet. Here, we demonstrate the fabrication of depth confined NV−^-− centers by combining low energy (1\,keV - 5\,keV) ion implantation and CVD overgrowth. By increasing the thickness of the overgrown layer (6\,nm - 100\,nm) the influence of surface noise is shown to decrease leading to bulk-like coherence properties of up to $450\,\upmu$s (Hahn-echo) and T2∗T_2^*T2∗​ dephasing times around $20\,\upmu$s. Monitoring the NV−^-− density as a function of the overgrowth time, we analyze the kinetics of the passivation in case of implanting ion doses of 1011^{11}11 15^{15}15N +^{+}+/cm2^22 and 1012^{12}12 15^{15}15N +^{+}+/cm2^22. The passivation turns out to occur faster for lower doses offering insights into sub-surface hydrogen diffusion in diamond. Analyzing the spin bath before and after overgrowth reveals a drastic reduction in paramagnetic spins after the CVD process but no NVH−^-− is found around the surviving NV−^-− centers. Checking the chemical composition in overgrown implantation sites with secondary-ion-mass-specrometry (SIMS), however, confirms significant amounts of hydrogen in the 15^{15}15N-implanted layers. Since the concentration found for hydrogen exceeds the one for nitrogen by far, we suggest that diffusing hydrogen interacts also with vacancies forming probably mostly diamagnetic defects. In the last part of this dissertation, NV−^-− centers are generated with sub-nanometer precision below a thin 13^{13}13C-enriched layer for quantum simulation. For fabricating the spin architecture starting from a 12^{12}12C base layer, we overgrow implanted nitrogen with a 13^{13}13C layer and bury the spins beneath a 30\,nm-thick 12^{12}12C capping layer. By measuring the coupling strength between the electron and nuclear spins, we deduce a NV−^-− placement accuracy reaching below one nanometer with respect to the 13^{13}13C-layer. Regarding the spin properties of the electron spins, no reduction in T2T_2T2​ is observed despite of the proximity to the dense 13^{13}13C-bath. As a consequence, the overgrowth of NV−^-− centers is demonstrated as a bottom-up approach to produce buried spin architectures with sharp isotopic transitions and efficient 13^{13}13C-NV−^-− coupling. Together with the potential for bulk-like coherence properties the synergy of implantation and overgrowth is a powerful tool to fabricate reproducible quantum systems with tailored properties and high depth confinement.
The negatively-charged nitrogen-vacancy (NV) center is the most studied optical center in diamond and is very important for applications in quantum information science. Many proposals for integrating NV centers in quantum and sensing applications rely on their tailored fabrication in ultra pure host material. In this study, we use ion implantation to controllably introduce nitrogen into high purity, low nitrogen chemical vapor deposition diamond samples. The properties of the resulting NV centers are studied as a function of implantation temperature, annealing temperature, and implantation fluence. We compare the implanted NV centers with native NV centers present deep in the bulk of the as-grown samples. The results for implanted NV centers are promising but indicate, at this stage, that the deep native NV centers possess overall superior optical properties. In particular, the implanted NV centers obtained after annealing at 2000 °C under a stabilizing pressure of 8 GPa showed an ensemble linewidth of 0.17 nm compared to 0.61 nm after annealing at 1000 °C. Over the same temperature range, the ensemble NV−/NV0 ratio increased by a factor of ∼5, although this was accompanied by an overall decrease in the NV count.
The negatively charged nitrogen-vacancy (NV-) center in diamond is a promising spin system for quantum sensing applications. NV-ensembles are favored for an improved signal-to-noise ratio and sensitivity. The optimization of diamond with NV-ensembles often requires a high NV concentration, a long spin coherence time T2 and a stable charge state. However, these key requirements are interdependent and can be difficult to optimize: nitrogen impurities as the main decoherence source of the NV spin limits the coherence time T2, and pursuing high NV concentration can deteriorate the NV-charge-state stability. Consequently, their best achievable combination becomes an essential question for the material characterization. In this work, we systematically investigate the NV center creation and properties in chemical vapor deposition (CVD) diamond. We have grown CVD diamond series with a varying nitrogen flow over four orders of magnitude, leading to a broad range of single substitutional nitrogen (P1 center) densities from 0.2 to 20 ppm. On these series, we study P1, NV creations and NV charge states after growth, as well as their transformation under subsequent electron beam irradiation. Furthermore, for a fixed nitrogen concentration, we optimize electron-irradiation fluences with two different accelerated electron energies. We discuss a general approach to determine the optimal irradiation conditions, for which an enhanced NV concentration and an optimum of NV charge states can both be satisfied. Moreover, through irradiation and annealing treatments, we monitor the change in T2 and aim to increase the NV density without compromising T2. We achieve NV concentrations from 1 to 168 ppb with T2 from 549 to 45.5 µs respectively. This study shows a pathway to engineer properties of NV-doped CVD diamonds for improved sensitivity.