Cryogenic CMOS (cryo-CMOS) quantum bit (qubit) control circuits are expected to overcome the interconnect complexity problem in large-scale quantum computers. However, since each qubit has a unique frequency for control, many power-hungry oscillators are needed to generate the frequencies at the cryogenic temperature stage of a refrigerator. In this article, to remove the oscillators from the refrigerator, we propose a cryo-CMOS signal selector (SS) consisting of two injection-locked oscillators that extract the specified frequency tone for qubit control from the multitone microwave signal. SS can reduce the power of signal generation for qubit control by 1/30. In addition, we propose a SS with a frequency-doubling function termed FDSS, based on the SS. FDSS can mitigate the local oscillator (LO)-RF leakage in microwave pulse generation for qubit control using direct conversion (DC). We demonstrate a cryo-CMOS DC-based qubit controller using FDSS. The measurement results show that the power dissipation and LO-RF leakage of the proposed qubit controller are reduced by 80% and 20dB, respectively, compared with conventional cryo-CMOS qubit controllers.
Cryogenic CMOS control and readout circuits tightly interfaced with the qubits have emerged as a promising solution for future quantum computers with tens-of-thousands to millions of qubits [1] –[5]. A lownoise cryo-CMOS receiver at
3−4 K integrated tightly with the lowcryogenic quantum processor can relax or even potentially eliminated the need for the HEMT LNA, and keep the whole control loop at cryogenic temperature, hence avoiding any high-speed interconnects to room temperature (Fig. 1). Additionally, wide bandwidths in the receiver enables qubit-multiplexing, where qubits can be frequency multiplexed with a spacing of
10MHz−40MHz, allowing anywhere from 10’s-100’s of qubits to be packed in to a single readout line with gigahertz-scale bandwidths. A second critical metric is power consumption, since the cooling power available in a typical dilution refrigerator is limited to a few watts at
3−4 K. Therefore, the control and readout circuits should be designed with low power consumption, projected to be
<1 mW per qubit (Fig. 1). While there has been initial progress in the design of cryo-CMOS readout systems, a leap forward is required in their overall power consumption to be viable for future quantum systems. In this work, we showcase the design and implementation of the first sub-mWper-qubit cryo-CMOS RX - a wideband, I/Q-downconversion,
4 K receiver for qubit readout that achieves
>1.9GHz of IF bandwidth with
>50 dB conversion gain and
0.7 dB NF while consuming only
17 mW of power consumption, thanks to various design techniques including near-threshold operation and low-1/f-noise passive mixers, representing
3−5× lower power consumption than prior works [2]–[3] while achieving similar noise, BW and gain performance. In addition, we demonstrate a real-time qubit read-out measurement by integrating our cryogenic-CMOS receiver with a transmon qubit.
Building a large-scale quantum computer requires the co-optimization of both the quantum bits (qubits) and their control electronics. By operating the CMOS control circuits at cryogenic temperatures (cryo-CMOS), and hence in close proximity to the cryogenic solid-state qubits, a compact quantum-computing system can be achieved, thus promising scalability to the large number of qubits required in a practical application. This work presents a cryo-CMOS microwave signal generator for frequency-multiplexed control of 4 × 32 qubits (32 qubits per RF output). A digitally intensive architecture offering full programmability of phase, amplitude, and frequency of the output microwave pulses and a wideband RF front end operating from 2 to 20 GHz allow targeting both spin qubits and transmons. The controller comprises a qubit-phase-tracking direct digital synthesis (DDS) back end for coherent qubit control and a single-sideband (SSB) RF front end optimized for minimum leakage between the qubit channels. Fabricated in Intel 22-nm FinFET technology, it achieves a 48-dB SNR and 45-dB spurious-free dynamic range (SFDR) in a 1-GHz data bandwidth when operating at 3 K, thus enabling high-fidelity qubit control. By exploiting the on-chip 4096-instruction memory, the capability to translate quantum algorithms to microwave signals has been demonstrated by coherently controlling a spin qubit at both 14 and 18 GHz.
In today's mainstream superconducting quantum computing platforms in a dilution refrigerator, the qubits work at a cryogenic temperature (CT) of a few tens of mK, while the qubit controller hardware works on plates with temperature ranging from a few K to room temperature (RT). The highly-integrated cryo-CMOS qubit controller ASIC that can fully work at 3-4K has been proven to be the most feasible way to scale down the quantum computing system [1–5]. In [1], a pulse modulator is implemented with a limited qubit driving capability, which can only generate fixed length symmetric driving pulse. The controllers in [2], [3] generated the RF driving pulse with a frequency division multiplexing (FDM) mode, with the power dissipation of 192mW/qubit and 46.5mW/qubit, respectively. In [4], a local oscillator (LO) was included to improve the controller integration level, and the chip power consumption was 24.1mW/qubit. An arbitrary waveform generation (AWG) functionality digital design was presented in [5] with a power consumption of 23.1mW/qubit. Nevertheless, with continuously increasing number of qubits to integrate, it remains as one of the major tasks to further reduce the power consumption and size of controller.
Accurate and low-noise generation and amplification of microwave signals are required for the manipulation and readout of quantum bits (qubits). A fault-tolerant quantum computer operates at deep cryogenic temperatures (i.e., <; 100mK) and requires thousands of qubits for running practical quantum algorithms. Consequently, CMOS radio-frequency (RF) integrated circuits operating at cryogenic temperatures down to 4 K (Cryo-CMOS) offer a higher level of system integration and scalability for future quantum computers. In this paper, we extensively discuss the role, benefits, and constraints of Cryo-CMOS for qubits control and readout. The main characteristics of the CMOS transistors and their impacts on RF circuit designs are described. Furthermore, opportunities and challenges of low noise RF signal generation and amplification are investigated.
Large-scale quantum computing holds promise for exponentially faster computation speed to address currently unsolvable problems. Nevertheless, biasing, driving and reading numerous physical qubits operating at cryogenic temperature remains an on-going challenge. In particular, the integration of cryogenic control and readout ICs appears mandatory to overcome the wiring bottleneck [1]–[3]. In this regard, the promising higher operating temperature (up to 1K) of silicon semiconductor qubits offers a more substantial cryogenic power budget, which could enable addressing larger qubit arrays with integrated cryogenic CMOS electronics. In the context of 100,000 qubits at 1K, the maximum power consumption allowed by cooling capability is about 1W within a compact footprint of just a few cm2, defining targets of2/qubit footprint. Focusing on the readout IC, the semiconductor-qubit coherence time also imposes a typical3.