Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physical Review Applied

Near-quantum-limited subgigahertz Ti N kinetic inductance traveling-wave parametric amplifier operating in a frequency-translating mode

Farzad Faramarzi, Sasha Sypkens, Ryan Stephenson, Byeong Ho Eom, Henry George LeDuc, Saptarshi Chaudhuri, Peter K. Day

Published Feb 25, 2025• 2 citations
Publisher

Abstract

We present the design and experimental characterization of a kinetic inductance traveling-wave parametric amplifier (KI-TWPA) for subgigahertz frequencies. KI-TWPAs amplify signals through mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here uses a compactly meandered $\mathrm{Ti}\mathrm{N}$ microstrip transmission line to achieve the length needed to amplify subgigahertz signals. It is operated in a frequency-translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5 GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850 MHz. Using $\mathrm{Ti}\mathrm{N}$ as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to $\mathrm{Nb}\mathrm{Ti}\mathrm{N}$, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.

DOI
10.1103/physrevapplied.23.024063

Related papers

A Near Quantum Limited Sub-GHz TiN Kinetic Inductance Traveling Wave Parametric Amplifier Operating in a Frequency Translating Mode

Farzad Faramarzi, Sasha Sypkens, Ryan Stephenson +4 more

We present the design and experimental characterization of a kinetic-inductance traveling-wave parametric amplifier (KI-TWPA) for sub-GHz frequencies. KI-TWPAs amplify signals through nonlinear mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here utilizes a compactly meandered TiN microstrip transmission line to achieve the length needed to amplify sub-GHz signals. It is operated in a frequency translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5~GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850~MHz. Use of TiN as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to NbTiN, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.

arXiv:2406.00530•Jun 1, 2024•3 citations

A 4–8 GHz kinetic inductance traveling-wave parametric amplifier using four-wave mixing with near quantum-limited noise performance

Farzad Faramarzi, Ryan Stephenson, Sasha Sypkens +3 more

Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.

arXiv:2402.11751•APL Quantum•Jul 11, 2024•25 citations

Kinetic Inductance Traveling Wave Parametric Amplifiers Near the Quantum Limit: Methodology and Characterization

Logan A. Howe, Andrea Giachero, Michael R. Vissers +7 more

We present a detailed simulation and design framework for realizing traveling wave parametric amplifiers (TWPAs) using the nonlinear kinetic inductance of disordered superconductors -- in our case niobium-titanium-nitride (NbTiN). These kinetic inductance TWPAs (KITs) operate via three-wave mixing (3WM) to achieve high broadband gain and near-quantum-limited (nQL) noise. Representative fabricated devices -- realized using an inverted microstrip (IMS), dispersion-engineered, artificial transmission line -- demonstrate power gains above 25 dB, bandwidths beyond 3 GHz, and achieve ultimate system noise levels of 1.1 quanta even when operated with no magnetic shielding. These performance metrics are competitive with state-of-the-art Josephson-junction-based TWPAs but involve simpler fabrication and able to providing three orders of magnitude higher dynamic range ($IIP_1 = -68$ dBm, $IIP_3 = -55$ dBm), and high magnetic field resilience -- making KITs an attractive technology for highly multiplexed readout of quantum information and superconducting detector systems.

arXiv:2507.07706•Jul 10, 2025•0 citations

Temperature and magnetic field limits of a kinetic inductance traveling-wave parametric amplifier

Lucas M. Janssen, Farzad Faramarzi, Henry George LeDuc +5 more

Kinetic-inductance traveling-wave parametric amplifiers (KI-TWPAs) offer broadband near-quantum-limited amplification with high saturation power. Due to the high critical magnetic fields of high-kinetic-inductance materials, KI-TWPAs should be resilient to magnetic fields. In this work, we study how magnetic field and temperature affect the performance of a KI-TWPA based on a thin-NbTiN inverse microstrip with a Nb ground plane. This KI-TWPA can provide substantial signal-to-noise ratio improvement ($ΔSNR$) up to in-plane magnetic fields of 0.35T and out-of-plane fields of 50mT, considerably higher than what has been demonstrated with TWPAs based on Josephson junctions. The field compatibility can be further improved by incorporating vortex traps and by using materials with higher critical fields. We also find that the gain does not degrade when the temperature is raised to 3K (limited by the Nb ground plane) while $ΔSNR$ decreases with temperature consistently with expectation. This demonstrates that KI-TWPAs can be used in experiments that need to be performed at relatively high temperatures. The operability of KI-TWPAs in high magnetic field opens the door to a wide range of applications in spin qubits, spin ensembles, topological qubits, low-power NMR, and the search for axion dark matter.

arXiv:2509.15043•Physical Review Applied•May 13, 2026•1 citation

Experimental Demonstration of a Balanced Travelling Wave Parametric Amplifier

Nikita Klimovich, Peter K. Day, Henry G. Leduc +1 more

Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at $f_s$ is indistinguishable from one at $f_p - f_s$, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180$^{\circ}$ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.

physics.ins-detCross-listedarXiv:2610.23810•Oct 19, 2026•0 citations

Superconducting microwave parametric amplifier based on a quasi-fractal slow propagation line

A. A. Adamyan, Sebastian E. de Graaf, Sergey Kubatkin +1 more

Quantum limited amplifiers are sought after for a wide range of applications within quantum technologies and sensing. One promising candidate is the travelling wave parametric amplifier which exploits the non-linear kinetic inductance of a superconducting transmission line. This type of microwave amplifier promises to deliver a high gain, a quantum limited noise performance over several GHz bandwidth, and a high dynamic range. However, practical realizations of this type of device have so far been limited by fabrication defects, since the length of the superconducting transmission line required for achieving substantial parametric gain is on the order of ∼1 m. Here, we report on a design for a microwave traveling wave amplifier based on a slow propagation line comprising a central strip with high kinetic inductance and quasi-fractal line-to-ground capacitors. Due to an enhanced per unit length inductance (73 nH cm−1) and capacitance (15 pF cm−1), the line has a microwave propagation velocity as low as 9.8 × 108 cm s−1. This translates into parametric gain up to 0.5 dB cm−1 and a total gain of 6 dB for just a ∼10 cm long transmission line. Moreover, the flexibility of the presented design allows balancing the line inductance and capacitance in order to keep the characteristic impedance close to 50 Ω and to suppress standing waves, both factors being essential in order to implement a practical parametric amplifier in the microwave domain.

Journal of Applied Physics•Feb 22, 2016•49 citations
We present the design and experimental characterization of a kinetic inductance traveling-wave parametric amplifier (KI-TWPA) for subgigahertz frequencies. KI-TWPAs amplify signals through mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here uses a compactly meandered TiN\mathrm{Ti}\mathrm{N}TiN microstrip transmission line to achieve the length needed to amplify subgigahertz signals. It is operated in a frequency-translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5 GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850 MHz. Using TiN\mathrm{Ti}\mathrm{N}TiN as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to NbTiN\mathrm{Nb}\mathrm{Ti}\mathrm{N}NbTiN, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.
We present the design and experimental characterization of a kinetic-inductance traveling-wave parametric amplifier (KI-TWPA) for sub-GHz frequencies. KI-TWPAs amplify signals through nonlinear mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here utilizes a compactly meandered TiN microstrip transmission line to achieve the length needed to amplify sub-GHz signals. It is operated in a frequency translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5~GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850~MHz. Use of TiN as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to NbTiN, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.
Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.
We present a detailed simulation and design framework for realizing traveling wave parametric amplifiers (TWPAs) using the nonlinear kinetic inductance of disordered superconductors -- in our case niobium-titanium-nitride (NbTiN). These kinetic inductance TWPAs (KITs) operate via three-wave mixing (3WM) to achieve high broadband gain and near-quantum-limited (nQL) noise. Representative fabricated devices -- realized using an inverted microstrip (IMS), dispersion-engineered, artificial transmission line -- demonstrate power gains above 25 dB, bandwidths beyond 3 GHz, and achieve ultimate system noise levels of 1.1 quanta even when operated with no magnetic shielding. These performance metrics are competitive with state-of-the-art Josephson-junction-based TWPAs but involve simpler fabrication and able to providing three orders of magnitude higher dynamic range (IIP1=−68IIP_1 = -68IIP1​=−68 dBm, IIP3=−55IIP_3 = -55IIP3​=−55 dBm), and high magnetic field resilience -- making KITs an attractive technology for highly multiplexed readout of quantum information and superconducting detector systems.
Kinetic-inductance traveling-wave parametric amplifiers (KI-TWPAs) offer broadband near-quantum-limited amplification with high saturation power. Due to the high critical magnetic fields of high-kinetic-inductance materials, KI-TWPAs should be resilient to magnetic fields. In this work, we study how magnetic field and temperature affect the performance of a KI-TWPA based on a thin-NbTiN inverse microstrip with a Nb ground plane. This KI-TWPA can provide substantial signal-to-noise ratio improvement (ΔSNRΔSNRΔSNR) up to in-plane magnetic fields of 0.35T and out-of-plane fields of 50mT, considerably higher than what has been demonstrated with TWPAs based on Josephson junctions. The field compatibility can be further improved by incorporating vortex traps and by using materials with higher critical fields. We also find that the gain does not degrade when the temperature is raised to 3K (limited by the Nb ground plane) while ΔSNRΔSNRΔSNR decreases with temperature consistently with expectation. This demonstrates that KI-TWPAs can be used in experiments that need to be performed at relatively high temperatures. The operability of KI-TWPAs in high magnetic field opens the door to a wide range of applications in spin qubits, spin ensembles, topological qubits, low-power NMR, and the search for axion dark matter.
Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at fsf_sfs​ is indistinguishable from one at fp−fsf_p - f_sfp​−fs​, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180∘^{\circ}∘ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.
Quantum limited amplifiers are sought after for a wide range of applications within quantum technologies and sensing. One promising candidate is the travelling wave parametric amplifier which exploits the non-linear kinetic inductance of a superconducting transmission line. This type of microwave amplifier promises to deliver a high gain, a quantum limited noise performance over several GHz bandwidth, and a high dynamic range. However, practical realizations of this type of device have so far been limited by fabrication defects, since the length of the superconducting transmission line required for achieving substantial parametric gain is on the order of ∼1 m. Here, we report on a design for a microwave traveling wave amplifier based on a slow propagation line comprising a central strip with high kinetic inductance and quasi-fractal line-to-ground capacitors. Due to an enhanced per unit length inductance (73 nH cm−1) and capacitance (15 pF cm−1), the line has a microwave propagation velocity as low as 9.8 × 108 cm s−1. This translates into parametric gain up to 0.5 dB cm−1 and a total gain of 6 dB for just a ∼10 cm long transmission line. Moreover, the flexibility of the presented design allows balancing the line inductance and capacitance in order to keep the characteristic impedance close to 50 Ω and to suppress standing waves, both factors being essential in order to implement a practical parametric amplifier in the microwave domain.