Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Quantum Computing, Communication, and Simulation

Design and performance of 1762 nm Tm-doped fiber amplifiers for manipulation and control of optical qubits in 133Ba+ ions

Robert E. Tench, Adrian Zepeda, Wiktor T. Walasik, Alexandre Amavigan, Jean-Marc Delavaux

Published Mar 12, 2024• 0 citations
Publisher

Abstract

We report the optical architecture, experimental performance, and simulated performance of polarization- maintaining CW and pulsed single clad Tm-doped fiber amplifiers designed to operate over a wavelength span of 1760—1960 nm. We highlight the potential applications of these amplifiers to quantum computing and quantum qubit experiments using 1762 nm light. Our amplifier exhibits 3 W CW output power and 20 W peak pulsed output power (2 MHz rep. rate, 10% duty cycle) at 1762 nm. Measurements of the wavelength response of the TDFA yield an experimental operating bandwidth extending from < 1750 nm to > 1920 nm. Simulations of the amplifier bandwidth indicate a 3 dB (50% FWHM) wavelength span of 1745 nm to 1980 nm (135 nm). Experimental output power and bandwidth results agree well with the simulations. The external noise figure for this amplifier ranges from 7.5 dB to 9.5 dB. No linewidth broadening was observed in a typical TDFA output when using a single frequency input laser source with a linewidth of 10 kHz. We discuss suitability and applications of the TDFA to 1762 nm enabled manipulation of optical qubits in trapped 133Ba+ ions.

DOI
10.1117/12.3001098

Related papers

High Power Single-Frequency 1762 nm Laser for Barium Ion Optical Qubits

Saïd Hamdi, Kentin Poncelet, Coline Lavit +4 more

Quantum processors based on ion traps (171Yb+,88Sr+,43Ca+or133Ba+) are one of the key components in the emergence of quantum technologies and have seen their interest explode in the last decade [1]. Although171Yb+ions are commonly used as qubits, a new alternative is based on133Ba+offering several key advantages in terms of lifetime, speed, fidelity and performance. The readout of the qubit is made by shelving the133Ba+ion directly to the metastable 5D5/2 state using a 1762 nm single-frequency laser radiation [2]. For quantum computing and optical qubit manipulation low noise and high-power laser at this wavelength is highly recommended. Thulium doped fiber amplifiers (TDFAs) with broad emission between 1600–2100 nm and high-power capabilities are one of the best candidates for this application. Walasik et al demonstrated a 3W-1762 nm single-frequency TDFA but phase and intensity noise weren't investigated [3].

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 23, 2025•0 citations

Pulsed-pump phosphorus-doped fiber Raman amplifier around 1260 nm for applications in quantum non-linear optics

Eilon Poem, Artem Golenchenko, Omri Davidson +3 more

We describe a fiber Raman amplifier for nanosecond and sub-nanosecond pulses centered around 1260 nm. The amplification takes place inside a 4.5-m-long polarization-maintaining phosphorus-doped fiber, pumped at 1080 nm by 3-ns-long pulses with a repetition rate of 200 kHz and up to 1.75 kW peak power. The input seed pulses are of sub-mW peak-power and minimal duration of 0.25 ns, carved out of a continuous-wave laser with sub-MHz linewidth. We obtain linearly polarized output pulses with peak powers of up to 1.4 kW, corresponding to peak-power conversion efficiency of over 80%. An ultrahigh small signal gain of 90 dB is achieved, and the signal-to-noise ratio 3 dB below the saturation power is above 20 dB. No significant temporal and spectral broadening is observed for output pulses up to 400 W peak power, and broadening at higher powers can be reduced by phase modulation of the seed pulse. Thus, nearly-transform-limited pulses with peak power up to 1 kW are obtained. Finally, we demonstrate the generation of pulses with controllable frequency chirp, pulses with variable width, and double pulses. This amplifier is thus suitable for coherent control of narrow atomic resonances, especially for the fast and coherent excitation of rubidium atoms to Rydberg states. These abilities open the way towards several important applications in quantum non-linear optics.

arXiv:2007.09190•Optics Express•Sep 25, 2020•5 citations

30 W-class tunable single-frequency thulium-doped fiber amplifier at 1730–1762 nm with low intensity noise

Kentin Poncelet, Thomas Dubé, Coline Lavit +7 more

We report a fully fibered, polarization-maintaining, single-frequency thulium-doped fiber amplifier operating between 1730 and 1762 nm and delivering more than 30 W of output power. Relative intensity noise is preserved after amplification, with a noise floor of -158 dBc/Hz between 100 kHz and 4 MHz. These results demonstrate the suitability of this source for quantum technology, including direct operation within the tuning range at 1762 nm for barium ion excitation or a possible nonlinear frequency conversion toward 813 nm for strontium atom trapping.

Optics Letters•Mar 31, 2026•0 citations

Scalable narrow linewidth high power laser for barium ion optical qubits

Morteza Ahmadi, Tarun Dutta, Manas Mukherjee

The linewidth of a laser plays a pivotal role in ensuring the high fidelity of ion trap quantum processors and optical clocks. As quantum computing endeavors scale up in qubit number, the demand for higher laser power with ultra-narrow linewidth becomes imperative, and leveraging fiber amplifiers emerges as a promising approach to meet these requirements. This study explores the effectiveness of thulium-doped fiber amplifiers (TDFAs) as a viable solution for addressing optical qubit transitions in trapped barium ion qubits. We demonstrate that by performing high-fidelity gates on the qubit while introducing minimal intensity noise, TDFAs do not significantly broaden the linewidth of the seed lasers. We employed a Voigt fitting scheme in conjunction with a delayed self-heterodyne method to accurately measure the linewidth independently, corroborating our findings through quadrupole spectroscopy with trapped barium ions. Our results show linewidth values of 160 ± 15 Hz and 156 ± 16 Hz, respectively, using these two methods, underscoring the reliability of our measurement techniques. The slight variation within the error-bars of the two methods can be attributed to factors such as amplified spontaneous emission in the TDFA or the influence of 1/f noise within the heterodyne setup delay line. These contribute to advancing our understanding of laser linewidth control in the context of ion trap quantum computing as well as stretching the availability of narrow linewidth, high-power tunable lasers beyond the C-band.

arXiv:2312.03388•Optics Express•Apr 16, 2024•5 citations

Highly customized 1010 nm, ns-pulsed Yb-doped fiber amplifier as a key tool for on-demand single-photon generation

Oliver de Vries, Marco Plötner, Florian Christaller +9 more

The development of highly customized technical devices is a decisive feature of technically complex setups, as frequently observed in quantum experiments. This paper describes the development and realization of an Yb-doped all-fiber amplifier system designed for such a special application, more specifically, an on-demand single-photon source based on four-wave mixing with rubidium Rydberg atoms. The laser is capable of generating bandwidth-limited configurable nanosecond pulses up to peak powers of >100 W and with pulse repetition frequencies (PRF) between 50 Hz and 1 MHz at selectable wavelengths (1008-1024 nm). Especially the amplification of the 1010 nm reference seed at the lower edge of the amplification range for Yb-based fibers is challenging and tends to produce amplified spontaneous emission (ASE) at higher wavelengths. To achieve high ASE suppression, particularly at low pulse repetition frequencies, two acousto-optical modulators (AOM) are utilized both for pulse picking and for temporal filtering. The synchronization between pulse repetition frequency and AOM driver signal allows pulse amplitude fluctuations to be kept below 1%, while ASE is suppressed by at least 85 dB (PRF = 1 MHz) and 65 dB (PRF = 1 kHz).

Optics Express•May 15, 2020•8 citations

Ground state absorption in thulium-doped fiber amplifier: experiment and modeling

Scott S.-H. Yam, Jaedon Kim

S-band ground state absorption in a thulium-doped fiber amplifier (TDFA) has been studied in detail experimentally and theoretically. While traditionally considered difficult to measure, its presence is shown to have significant impact on amplifier power excursion during dynamic wavelength add-drop, due to the energy transitions inherent to the Tm/sup 3+/ ion. For specific pumping scheme and operating conditions, gain increases with increasing signal input, a behavior significantly different from conventional three-level optical amplifiers. Numerical models are presented that correctly account for these phenomena. This promises to provide insight for gain control algorithms for TDFAs under bursty traffic conditions in a future reconfigurable wavelength division multiplexed environment.

IEEE Journal of Selected Topics in Quantum Electronics•Jul 1, 2006•24 citations
We report the optical architecture, experimental performance, and simulated performance of polarization- maintaining CW and pulsed single clad Tm-doped fiber amplifiers designed to operate over a wavelength span of 1760—1960 nm. We highlight the potential applications of these amplifiers to quantum computing and quantum qubit experiments using 1762 nm light. Our amplifier exhibits 3 W CW output power and 20 W peak pulsed output power (2 MHz rep. rate, 10% duty cycle) at 1762 nm. Measurements of the wavelength response of the TDFA yield an experimental operating bandwidth extending from < 1750 nm to > 1920 nm. Simulations of the amplifier bandwidth indicate a 3 dB (50% FWHM) wavelength span of 1745 nm to 1980 nm (135 nm). Experimental output power and bandwidth results agree well with the simulations. The external noise figure for this amplifier ranges from 7.5 dB to 9.5 dB. No linewidth broadening was observed in a typical TDFA output when using a single frequency input laser source with a linewidth of 10 kHz. We discuss suitability and applications of the TDFA to 1762 nm enabled manipulation of optical qubits in trapped 133Ba+ ions.
Quantum processors based on ion traps (171Yb+,88Sr+,43Ca+or133Ba+) are one of the key components in the emergence of quantum technologies and have seen their interest explode in the last decade [1]. Although171Yb+ions are commonly used as qubits, a new alternative is based on133Ba+offering several key advantages in terms of lifetime, speed, fidelity and performance. The readout of the qubit is made by shelving the133Ba+ion directly to the metastable 5D5/2 state using a 1762 nm single-frequency laser radiation [2]. For quantum computing and optical qubit manipulation low noise and high-power laser at this wavelength is highly recommended. Thulium doped fiber amplifiers (TDFAs) with broad emission between 1600–2100 nm and high-power capabilities are one of the best candidates for this application. Walasik et al demonstrated a 3W-1762 nm single-frequency TDFA but phase and intensity noise weren't investigated [3].
We describe a fiber Raman amplifier for nanosecond and sub-nanosecond pulses centered around 1260 nm. The amplification takes place inside a 4.5-m-long polarization-maintaining phosphorus-doped fiber, pumped at 1080 nm by 3-ns-long pulses with a repetition rate of 200 kHz and up to 1.75 kW peak power. The input seed pulses are of sub-mW peak-power and minimal duration of 0.25 ns, carved out of a continuous-wave laser with sub-MHz linewidth. We obtain linearly polarized output pulses with peak powers of up to 1.4 kW, corresponding to peak-power conversion efficiency of over 80%. An ultrahigh small signal gain of 90 dB is achieved, and the signal-to-noise ratio 3 dB below the saturation power is above 20 dB. No significant temporal and spectral broadening is observed for output pulses up to 400 W peak power, and broadening at higher powers can be reduced by phase modulation of the seed pulse. Thus, nearly-transform-limited pulses with peak power up to 1 kW are obtained. Finally, we demonstrate the generation of pulses with controllable frequency chirp, pulses with variable width, and double pulses. This amplifier is thus suitable for coherent control of narrow atomic resonances, especially for the fast and coherent excitation of rubidium atoms to Rydberg states. These abilities open the way towards several important applications in quantum non-linear optics.
We report a fully fibered, polarization-maintaining, single-frequency thulium-doped fiber amplifier operating between 1730 and 1762 nm and delivering more than 30 W of output power. Relative intensity noise is preserved after amplification, with a noise floor of -158 dBc/Hz between 100 kHz and 4 MHz. These results demonstrate the suitability of this source for quantum technology, including direct operation within the tuning range at 1762 nm for barium ion excitation or a possible nonlinear frequency conversion toward 813 nm for strontium atom trapping.
The linewidth of a laser plays a pivotal role in ensuring the high fidelity of ion trap quantum processors and optical clocks. As quantum computing endeavors scale up in qubit number, the demand for higher laser power with ultra-narrow linewidth becomes imperative, and leveraging fiber amplifiers emerges as a promising approach to meet these requirements. This study explores the effectiveness of thulium-doped fiber amplifiers (TDFAs) as a viable solution for addressing optical qubit transitions in trapped barium ion qubits. We demonstrate that by performing high-fidelity gates on the qubit while introducing minimal intensity noise, TDFAs do not significantly broaden the linewidth of the seed lasers. We employed a Voigt fitting scheme in conjunction with a delayed self-heterodyne method to accurately measure the linewidth independently, corroborating our findings through quadrupole spectroscopy with trapped barium ions. Our results show linewidth values of 160 ± 15 Hz and 156 ± 16 Hz, respectively, using these two methods, underscoring the reliability of our measurement techniques. The slight variation within the error-bars of the two methods can be attributed to factors such as amplified spontaneous emission in the TDFA or the influence of 1/f noise within the heterodyne setup delay line. These contribute to advancing our understanding of laser linewidth control in the context of ion trap quantum computing as well as stretching the availability of narrow linewidth, high-power tunable lasers beyond the C-band.
The development of highly customized technical devices is a decisive feature of technically complex setups, as frequently observed in quantum experiments. This paper describes the development and realization of an Yb-doped all-fiber amplifier system designed for such a special application, more specifically, an on-demand single-photon source based on four-wave mixing with rubidium Rydberg atoms. The laser is capable of generating bandwidth-limited configurable nanosecond pulses up to peak powers of >100 W and with pulse repetition frequencies (PRF) between 50 Hz and 1 MHz at selectable wavelengths (1008-1024 nm). Especially the amplification of the 1010 nm reference seed at the lower edge of the amplification range for Yb-based fibers is challenging and tends to produce amplified spontaneous emission (ASE) at higher wavelengths. To achieve high ASE suppression, particularly at low pulse repetition frequencies, two acousto-optical modulators (AOM) are utilized both for pulse picking and for temporal filtering. The synchronization between pulse repetition frequency and AOM driver signal allows pulse amplitude fluctuations to be kept below 1%, while ASE is suppressed by at least 85 dB (PRF = 1 MHz) and 65 dB (PRF = 1 kHz).
S-band ground state absorption in a thulium-doped fiber amplifier (TDFA) has been studied in detail experimentally and theoretically. While traditionally considered difficult to measure, its presence is shown to have significant impact on amplifier power excursion during dynamic wavelength add-drop, due to the energy transitions inherent to the Tm/sup 3+/ ion. For specific pumping scheme and operating conditions, gain increases with increasing signal input, a behavior significantly different from conventional three-level optical amplifiers. Numerical models are presented that correctly account for these phenomena. This promises to provide insight for gain control algorithms for TDFAs under bursty traffic conditions in a future reconfigurable wavelength division multiplexed environment.