Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2007.09190 · Optics Express

Pulsed-pump phosphorus-doped fiber Raman amplifier around 1260 nm for applications in quantum non-linear optics

Eilon Poem, Artem Golenchenko, Omri Davidson, Or Arenfrid, Ran Finkelstein, Ofer Firstenberg

Published Sep 25, 2020• 5 citations
arXivHTMLPDF

Abstract

We describe a fiber Raman amplifier for nanosecond and sub-nanosecond pulses centered around 1260 nm. The amplification takes place inside a 4.5-m-long polarization-maintaining phosphorus-doped fiber, pumped at 1080 nm by 3-ns-long pulses with a repetition rate of 200 kHz and up to 1.75 kW peak power. The input seed pulses are of sub-mW peak-power and minimal duration of 0.25 ns, carved out of a continuous-wave laser with sub-MHz linewidth. We obtain linearly polarized output pulses with peak powers of up to 1.4 kW, corresponding to peak-power conversion efficiency of over 80%. An ultrahigh small signal gain of 90 dB is achieved, and the signal-to-noise ratio 3 dB below the saturation power is above 20 dB. No significant temporal and spectral broadening is observed for output pulses up to 400 W peak power, and broadening at higher powers can be reduced by phase modulation of the seed pulse. Thus, nearly-transform-limited pulses with peak power up to 1 kW are obtained. Finally, we demonstrate the generation of pulses with controllable frequency chirp, pulses with variable width, and double pulses. This amplifier is thus suitable for coherent control of narrow atomic resonances, especially for the fast and coherent excitation of rubidium atoms to Rydberg states. These abilities open the way towards several important applications in quantum non-linear optics.

DOI
10.1364/oe.404015

Related papers

Highly customized 1010 nm, ns-pulsed Yb-doped fiber amplifier as a key tool for on-demand single-photon generation

Oliver de Vries, Marco Plötner, Florian Christaller +9 more

The development of highly customized technical devices is a decisive feature of technically complex setups, as frequently observed in quantum experiments. This paper describes the development and realization of an Yb-doped all-fiber amplifier system designed for such a special application, more specifically, an on-demand single-photon source based on four-wave mixing with rubidium Rydberg atoms. The laser is capable of generating bandwidth-limited configurable nanosecond pulses up to peak powers of >100 W and with pulse repetition frequencies (PRF) between 50 Hz and 1 MHz at selectable wavelengths (1008-1024 nm). Especially the amplification of the 1010 nm reference seed at the lower edge of the amplification range for Yb-based fibers is challenging and tends to produce amplified spontaneous emission (ASE) at higher wavelengths. To achieve high ASE suppression, particularly at low pulse repetition frequencies, two acousto-optical modulators (AOM) are utilized both for pulse picking and for temporal filtering. The synchronization between pulse repetition frequency and AOM driver signal allows pulse amplitude fluctuations to be kept below 1%, while ASE is suppressed by at least 85 dB (PRF = 1 MHz) and 65 dB (PRF = 1 kHz).

Optics Express•May 15, 2020•8 citations

Design and performance of 1762 nm Tm-doped fiber amplifiers for manipulation and control of optical qubits in 133Ba+ ions

Robert E. Tench, Adrian Zepeda, Wiktor T. Walasik +2 more

We report the optical architecture, experimental performance, and simulated performance of polarization- maintaining CW and pulsed single clad Tm-doped fiber amplifiers designed to operate over a wavelength span of 1760—1960 nm. We highlight the potential applications of these amplifiers to quantum computing and quantum qubit experiments using 1762 nm light. Our amplifier exhibits 3 W CW output power and 20 W peak pulsed output power (2 MHz rep. rate, 10% duty cycle) at 1762 nm. Measurements of the wavelength response of the TDFA yield an experimental operating bandwidth extending from < 1750 nm to > 1920 nm. Simulations of the amplifier bandwidth indicate a 3 dB (50% FWHM) wavelength span of 1745 nm to 1980 nm (135 nm). Experimental output power and bandwidth results agree well with the simulations. The external noise figure for this amplifier ranges from 7.5 dB to 9.5 dB. No linewidth broadening was observed in a typical TDFA output when using a single frequency input laser source with a linewidth of 10 kHz. We discuss suitability and applications of the TDFA to 1762 nm enabled manipulation of optical qubits in trapped 133Ba+ ions.

Quantum Computing, Communication, and Simulation•Mar 12, 2024•0 citations

Coherent Rydberg excitation of single atoms using a pulsed fiber amplifier

Ying-Wen Zhang, Yang Wang, Chen-Long Xu +2 more

In recent years, the growing scale of programmable neutral-atom arrays has led to an increasing demand for higher-power Rydberg excitation light. Although pulsed amplifiers deliver higher peak power than continuous-wave lasers, their use for efficient coherent Rydberg excitation of single atoms in arrays has been limited by challenges such as pulse distortion, synchronization with excitation sequences, and spectral linewidth broadening. Here, we address these issues using a fiber-based master-oscillator power-amplifier system. We demonstrate efficient coherent Rydberg excitation of single atoms in a rubidium atom array, achieving performance comparable to continuous-wave methods. This study provides a potentially new technical pathway toward future large-scale quantum simulation and computation with Rydberg atom arrays.

quant-pharXiv:2604.13436•Chinese Physics B•Apr 16, 2026•0 citations

Phase Sensitive Amplification in a Periodically Poled Silica Fiber

Nicolas Englebert, Francesco De Lucia, Pier J. A. Sazio +2 more

Summary form only given. When a signal propagates through a transmission line, it is deteriorated by amplitude and phase noise, which reduces its signal-to-noise ratio (SNR) [1]. According to Shannon's theory, the SNR determines the maximum spectral efficiency. It is therefore necessary to limit the noise [3]. For this purpose, one can use phase sensitive amplifiers (PSA) instead of phase insensitive amplifiers (PIA) like Erbium-doped fiber amplifiers. PSAs amplify only one phase quadrature of the signal while deamplifying the other, thanks to a required phase relationship between the pump and the signal. This unique property, known as phase-squeezing, allows to obtain noise figures (NF) as low as 0 dB whereas PIAs, based on stimulated emission, cannot be go below the 3 dB quantum limit [2]. Moreover, the phase-squeezing property of PSAs can be used for quantum communication or even in metrology [1]. PSA can be realized with χ(2)material through degenerate parametric amplification [2]. The large spectral separation between the pump and the signal makes it very easy to filter out the pump after amplification. A ± 11 dB amplification with a sub-quantum NF and a regeneration of a DPSK signal was experimentally performed in LiNbO3 [3]. A fiber based approach would however be preferable for telecommunication purposes. PSA's based on four wave-mixing have been demonstrated, but the long length and the difficulty to separate pump from the signal [1] hinders its practical implementation. Here we present the first demonstration of a PSA based on periodically poled silica fiber (PPSF). This design has the advantage of all-fiber devices as well as simple pump filtering. The experimental set-up is depicted in Figure 1. A 20 mW CW fiber laser at 1550 nm is sent through a 99:1 coupler to be divided into a signal and a pump. The pump is modulated into 1 ns wide pulses with a repetition rate of 50 MHz. It is then amplified and frequency doubled in a PPLN crystal. The peak power of the 775 nm pump pulses reaches 10W. The pump and CW signal are then combined in a WDM and sent through a 30 cm long PPSF [4] where the signal undergoes parametric amplification. A second WDM is used to separate the pump from the amplified signal. The wave plates and the polarization controller in the pump path, allow to simultaneously control the polarization of the pump and the power in the fundamental mode of the PPSF (at 775 nm the fibre is slightly multimode). The relative phase between the pump and signal is controlled by fine tuning the frequency of the laser via a built-in piezo.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 1, 2019•0 citations

30 W-class tunable single-frequency thulium-doped fiber amplifier at 1730–1762 nm with low intensity noise

Kentin Poncelet, Thomas Dubé, Coline Lavit +7 more

We report a fully fibered, polarization-maintaining, single-frequency thulium-doped fiber amplifier operating between 1730 and 1762 nm and delivering more than 30 W of output power. Relative intensity noise is preserved after amplification, with a noise floor of -158 dBc/Hz between 100 kHz and 4 MHz. These results demonstrate the suitability of this source for quantum technology, including direct operation within the tuning range at 1762 nm for barium ion excitation or a possible nonlinear frequency conversion toward 813 nm for strontium atom trapping.

Optics Letters•Mar 31, 2026•0 citations

Imaging and quantum interference in a low light level Raman amplifier

Michael D. Duncan, Rita Mahon, John F. Reintjes +1 more

We have previously reported experimental results of Raman amplification of a low-light-level seed-Stokes beam in the transient limit.1 Here we present results of measurements which used a 10-nsec seed-injected Nd:YAG laser. The 532-nm frequency-doubled output had a duration of 8.5 ns and was used both to generate a 4.5-ns duration seed-Stokes pulse at 683 nm and to pump the 1-m long Raman amplifier. The seed-Stokes beam was spatially filtered, apertured at the Airy minimum, and collimated before the amplifier at a diameter of 5.2 mm. Likewise, the spatial mode of the pump was optimized to be as smooth as possible and was collimated into the Raman amplifier at a diameter of 3.4 mm. With no seed Stokes incident in the amplifier, random spatial patterns characteristic of the quantum-noise initiated, self­generated Stokes light were observed over a spatially gain-narrowed beam size supporting ~ 12 spatial modes. For the Raman gains of ~105 used in these experiments the number of temporal modes was 1.8. The seed-Stokes light was used to illuminate a bar chart of line-width 0.315 mm, and either a direct image of the bar chart, or its Fourier transform, was amplified in the Raman amplifier. The original bar chart image was then observed using an intensified camera. As the level of seed-Stokes was reduced to that approaching one photon per spatial-temporal mode, we were able to observe intensity modulations approaching 100% within the amplified bar chart images. Modulation levels of a few percent persist out to input levels of ~103 photons per mode. This observation is consistent with an interpretation of interference between electric field of the seed-Stokes beam and the vacuum fluctuations present in the amplifier but is inconsistent with a photon number description where the maximum predicted modulation would be only 50%.

Annual Meeting Optical Society of America•Jan 1, 1991•0 citations
We describe a fiber Raman amplifier for nanosecond and sub-nanosecond pulses centered around 1260 nm. The amplification takes place inside a 4.5-m-long polarization-maintaining phosphorus-doped fiber, pumped at 1080 nm by 3-ns-long pulses with a repetition rate of 200 kHz and up to 1.75 kW peak power. The input seed pulses are of sub-mW peak-power and minimal duration of 0.25 ns, carved out of a continuous-wave laser with sub-MHz linewidth. We obtain linearly polarized output pulses with peak powers of up to 1.4 kW, corresponding to peak-power conversion efficiency of over 80%. An ultrahigh small signal gain of 90 dB is achieved, and the signal-to-noise ratio 3 dB below the saturation power is above 20 dB. No significant temporal and spectral broadening is observed for output pulses up to 400 W peak power, and broadening at higher powers can be reduced by phase modulation of the seed pulse. Thus, nearly-transform-limited pulses with peak power up to 1 kW are obtained. Finally, we demonstrate the generation of pulses with controllable frequency chirp, pulses with variable width, and double pulses. This amplifier is thus suitable for coherent control of narrow atomic resonances, especially for the fast and coherent excitation of rubidium atoms to Rydberg states. These abilities open the way towards several important applications in quantum non-linear optics.
The development of highly customized technical devices is a decisive feature of technically complex setups, as frequently observed in quantum experiments. This paper describes the development and realization of an Yb-doped all-fiber amplifier system designed for such a special application, more specifically, an on-demand single-photon source based on four-wave mixing with rubidium Rydberg atoms. The laser is capable of generating bandwidth-limited configurable nanosecond pulses up to peak powers of >100 W and with pulse repetition frequencies (PRF) between 50 Hz and 1 MHz at selectable wavelengths (1008-1024 nm). Especially the amplification of the 1010 nm reference seed at the lower edge of the amplification range for Yb-based fibers is challenging and tends to produce amplified spontaneous emission (ASE) at higher wavelengths. To achieve high ASE suppression, particularly at low pulse repetition frequencies, two acousto-optical modulators (AOM) are utilized both for pulse picking and for temporal filtering. The synchronization between pulse repetition frequency and AOM driver signal allows pulse amplitude fluctuations to be kept below 1%, while ASE is suppressed by at least 85 dB (PRF = 1 MHz) and 65 dB (PRF = 1 kHz).
We report the optical architecture, experimental performance, and simulated performance of polarization- maintaining CW and pulsed single clad Tm-doped fiber amplifiers designed to operate over a wavelength span of 1760—1960 nm. We highlight the potential applications of these amplifiers to quantum computing and quantum qubit experiments using 1762 nm light. Our amplifier exhibits 3 W CW output power and 20 W peak pulsed output power (2 MHz rep. rate, 10% duty cycle) at 1762 nm. Measurements of the wavelength response of the TDFA yield an experimental operating bandwidth extending from < 1750 nm to > 1920 nm. Simulations of the amplifier bandwidth indicate a 3 dB (50% FWHM) wavelength span of 1745 nm to 1980 nm (135 nm). Experimental output power and bandwidth results agree well with the simulations. The external noise figure for this amplifier ranges from 7.5 dB to 9.5 dB. No linewidth broadening was observed in a typical TDFA output when using a single frequency input laser source with a linewidth of 10 kHz. We discuss suitability and applications of the TDFA to 1762 nm enabled manipulation of optical qubits in trapped 133Ba+ ions.
In recent years, the growing scale of programmable neutral-atom arrays has led to an increasing demand for higher-power Rydberg excitation light. Although pulsed amplifiers deliver higher peak power than continuous-wave lasers, their use for efficient coherent Rydberg excitation of single atoms in arrays has been limited by challenges such as pulse distortion, synchronization with excitation sequences, and spectral linewidth broadening. Here, we address these issues using a fiber-based master-oscillator power-amplifier system. We demonstrate efficient coherent Rydberg excitation of single atoms in a rubidium atom array, achieving performance comparable to continuous-wave methods. This study provides a potentially new technical pathway toward future large-scale quantum simulation and computation with Rydberg atom arrays.
Summary form only given. When a signal propagates through a transmission line, it is deteriorated by amplitude and phase noise, which reduces its signal-to-noise ratio (SNR) [1]. According to Shannon's theory, the SNR determines the maximum spectral efficiency. It is therefore necessary to limit the noise [3]. For this purpose, one can use phase sensitive amplifiers (PSA) instead of phase insensitive amplifiers (PIA) like Erbium-doped fiber amplifiers. PSAs amplify only one phase quadrature of the signal while deamplifying the other, thanks to a required phase relationship between the pump and the signal. This unique property, known as phase-squeezing, allows to obtain noise figures (NF) as low as 0 dB whereas PIAs, based on stimulated emission, cannot be go below the 3 dB quantum limit [2]. Moreover, the phase-squeezing property of PSAs can be used for quantum communication or even in metrology [1]. PSA can be realized with χ(2)material through degenerate parametric amplification [2]. The large spectral separation between the pump and the signal makes it very easy to filter out the pump after amplification. A ± 11 dB amplification with a sub-quantum NF and a regeneration of a DPSK signal was experimentally performed in LiNbO3 [3]. A fiber based approach would however be preferable for telecommunication purposes. PSA's based on four wave-mixing have been demonstrated, but the long length and the difficulty to separate pump from the signal [1] hinders its practical implementation. Here we present the first demonstration of a PSA based on periodically poled silica fiber (PPSF). This design has the advantage of all-fiber devices as well as simple pump filtering. The experimental set-up is depicted in Figure 1. A 20 mW CW fiber laser at 1550 nm is sent through a 99:1 coupler to be divided into a signal and a pump. The pump is modulated into 1 ns wide pulses with a repetition rate of 50 MHz. It is then amplified and frequency doubled in a PPLN crystal. The peak power of the 775 nm pump pulses reaches 10W. The pump and CW signal are then combined in a WDM and sent through a 30 cm long PPSF [4] where the signal undergoes parametric amplification. A second WDM is used to separate the pump from the amplified signal. The wave plates and the polarization controller in the pump path, allow to simultaneously control the polarization of the pump and the power in the fundamental mode of the PPSF (at 775 nm the fibre is slightly multimode). The relative phase between the pump and signal is controlled by fine tuning the frequency of the laser via a built-in piezo.
We report a fully fibered, polarization-maintaining, single-frequency thulium-doped fiber amplifier operating between 1730 and 1762 nm and delivering more than 30 W of output power. Relative intensity noise is preserved after amplification, with a noise floor of -158 dBc/Hz between 100 kHz and 4 MHz. These results demonstrate the suitability of this source for quantum technology, including direct operation within the tuning range at 1762 nm for barium ion excitation or a possible nonlinear frequency conversion toward 813 nm for strontium atom trapping.
We have previously reported experimental results of Raman amplification of a low-light-level seed-Stokes beam in the transient limit.1 Here we present results of measurements which used a 10-nsec seed-injected Nd:YAG laser. The 532-nm frequency-doubled output had a duration of 8.5 ns and was used both to generate a 4.5-ns duration seed-Stokes pulse at 683 nm and to pump the 1-m long Raman amplifier. The seed-Stokes beam was spatially filtered, apertured at the Airy minimum, and collimated before the amplifier at a diameter of 5.2 mm. Likewise, the spatial mode of the pump was optimized to be as smooth as possible and was collimated into the Raman amplifier at a diameter of 3.4 mm. With no seed Stokes incident in the amplifier, random spatial patterns characteristic of the quantum-noise initiated, self­generated Stokes light were observed over a spatially gain-narrowed beam size supporting ~ 12 spatial modes. For the Raman gains of ~105 used in these experiments the number of temporal modes was 1.8. The seed-Stokes light was used to illuminate a bar chart of line-width 0.315 mm, and either a direct image of the bar chart, or its Fourier transform, was amplified in the Raman amplifier. The original bar chart image was then observed using an intensified camera. As the level of seed-Stokes was reduced to that approaching one photon per spatial-temporal mode, we were able to observe intensity modulations approaching 100% within the amplified bar chart images. Modulation levels of a few percent persist out to input levels of ~103 photons per mode. This observation is consistent with an interpretation of interference between electric field of the seed-Stokes beam and the vacuum fluctuations present in the amplifier but is inconsistent with a photon number description where the maximum predicted modulation would be only 50%.