Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Amplitude-controllable microwave pulse generator using single-flux-quantum pulse pairs for qubit control

Hongxiang Shen, Naoki Takeuchi, Yuki Yamanashi, Nobuyuki Yoshikawa

Published Jul 19, 2023• 9 citations
Publisher

Abstract

Abstract To achieve large-scale quantum processors, cryogenic quantum-bit (qubit) interface circuits that can control qubits inside a dilution refrigerator are indispensable. Superconducting single-flux quantum (SFQ) circuits are a promising building block for qubit interface circuits because SFQ circuits can operate with high clock frequencies and low power dissipation. In the present study, we developed an SFQ-based qubit interface circuit that we refer to as a pulse-pair microwave pulse generator (PP-MPG). The PP-MPG can generate microwave pulses for qubit control, with the microwave amplitude controlled based on the delay between paired SFQ pulses. By finely adjusting the delay with delay controlling circuits, the microwave amplitude can be controlled over a wide range. We fabricated a PP-MPG chip and tested it at 4.2 K, showing that the microwave amplitude can be controlled over a range of approximately 30 dB. Our results show that the PP-MPG has the potential for use in future large-scale quantum processors.

DOI
10.1088/1361-6668/ace8c7

Related papers

Implementation of SFQ Microwave Choppers for Controlling Quantum Bits

Shu Miura, Naoki Takeuchi, Yuki Yamanashi +1 more

In order to control the state of qubits by a microwave pulse, the irradiation time and the amplitude have to be controlled precisely. We have developed a single-flux-quantum (SFQ) microwave chopper for high-speed switching of microwave pulses. The proposed chopper is composed of a DC/SFQ convertor, an SFQ switch, a PTL driver, and a superconducting low-pass filter (LPF). The chopper converts an input microwave, which is generated by an external microwave generator at the room temperature, into microwave pulses by using start/stop SFQ control signals. We designed and implemented a microwave chopper module, which can be attached to dilution refrigerators. SFQ chips were fabricated using the ISTEC 2.5 kA/cm2 Nb process. We tested the microwave chopper module at 4.2 K, and demonstrated that a 5-GHz microwave whose amplitude ranging from 0 μV to 150 μV can be chopped by the SFQ control signals.

Physics Procedia•Jan 1, 2012•3 citations

Compact RSFQ microwave pulse generator based on an integrated RF module for controlling superconducting qubits

Yuxing He, Hongxiang Shen, Shiori Michibayashi +5 more

An on-chip superconducting microwave pulse generator (MPG), incorporating rapid single-flux-quantum (RSFQ) logic gates and passive radio frequency (RF) components, is an energy-efficient solution for controlling superconducting quantum bits (qubits). Traditional RSFQ MPG designs, however, suffer from a large footprint as multiple RF components (including impedance matching networks, filters, etc.) are separately implemented one after another. In this Letter, we propose a compact on-chip MPG by introducing an integrated RF module. Using a generalized filter synthesis technique, the integrated RF module combines the functionalities of impedance matching and bandpass filtering as a single inductor-capacitor (LC) lumped network. Plenty of circuit elements can, thus, be saved, and the resultant LC network is applicable to both real and complex terminal impedance cases. For validation, a superconducting MPG adopting a fourth-order, 5 GHz centered, 100 MHz bandwidth integrated RF module is designed and fabricated, whose correct operations are confirmed through both simulation and measurement. These results raise the availability of controlling large-scale quantum systems by low-power superconductor technology in the future.

Applied Physics Letters•Feb 7, 2022•14 citations

Pulse-Density-Modulated Microwave Generator Using Single-Flux-Quantum Circuits for Controlling Qubits

Akira Kunihiro, Yuki Yamanashi, Nobuyuki Yoshikawa

Superconducting qubits are generally controlled by irradiation with microwave pulses. We propose a 5-GHz-range microwave pulse generator based on pulse density modulation for controlling qubits using single-flux-quantum (SFQ) circuits. The proposed microwave pulse generator comprises a 100-GHz circular shift register and a band-pass filter (BPF). In this study, we investigated the relationship between the target envelope of the microwave amplitude and the SFQ pulse density based on the transfer function for the BPF and the frequency spectrum of an SFQ pulse. We implemented a 64-bit circular shift register and demonstrated its operation up to 68 GHz.

IEEE Transactions on Applied Superconductivity•Mar 10, 2023•3 citations

Generating Microwave Signals with Enhancive Amplitudes Using Superconductor Single Flux Quantum Pulses for Controlling Quantum Bit

Hongxiang Shen, Yuxing He, Zeyu Han +6 more

Abstract In this study, the on‐chip generation of microwave signals are proposed for controlling nearby quantum bits in a low‐temperature environment, utilizing superconducting logical and RF components. To achieve enhanced amplitude of the microwave, superconducting single flux quantum (SFQ) pulse pairs are employed, which can have either the same or reversal polarity, serving as the basic elements of the generator. The SFQ pulse pairs are then combined and wave‐shaped by using a microwave combining filter, which finally outputs desired microwave signals with narrow line‐width. The amplitude of the microwave signal correlates with the interval between two SFQ pulses in a pair and can be adjusted accordingly. To validate the proposal, test chips are fabricated and performed experiments. The experimental results confirm that the method using a reverse‐polarity pulse can maximize the output microwave amplitude and provide control of the initial phase of the output microwave. This improvement offers a superior alternative for generating microwaves using superconducting circuits to control quantum bits.

Advanced Quantum Technologies•Apr 11, 2024•7 citations

Low power single flux quantum qubit control circuit without high-frequency input

Bicong Weng, Wei Peng, Jie Ren

Abstract The use of high-frequency input signals from room-temperature microwave sources makes it difficult to scale up the number of quantum bits in universal quantum computers. To address this issue, superconducting single flux quantum (SFQ) integrated circuits are being explored as suitable candidates for qubit manipulation in universal quantum computers. This paper deals with a scalable SFQ qubit control circuit (SQCC) structure that requires only low-frequency input. The circuit mainly consists of a pulse generator and a counter, that output the SFQ pulse train with adjustable frequency and a controllable number of pulses, which is applicable to control single-qubit Clifford operations. The design of low-voltage rapid single flux quantum (LV-RSFQ) and energy-efficient rapid single flux quantum (ERSFQ) for the SQCC achieves low power consumption and provides a basis for scaling up SQCC to control more qubits. The proposed circuits are fabricated under the SIMIT-Nb03 process and successfully pass test verification. The achieved test results reveal that the adjustable output frequency ranges of the SQCC based on the LV-RSFQ and ERSFQ designs in order are [2.40, 8.11] GHz and [4.81, 5.14] GHz. In the operating frequency range, the circuit is able to generate the correct number of SFQ pulses under control. The controllable number range is from 1 to 128. When the circuits operate at 5 GHz, the total power consumptions of the above circuits in order are 23.88 μW and 6.2 μW. All input signals are low-frequency signals, which frees the control of large-scale qubits from limitations caused by high-frequency inputs produced by room-temperature microwave sources.

Superconductor Science and Technology•Jul 11, 2023•4 citations

Coherence-limited digital control of a superconducting qubit using a Josephson pulse generator at 3 K

M. A. Castellanos-Beltran, A. J. Sirois, L. Howe +4 more

Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime $T_1$, coherence time $T_2^*$ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for $T_1$ and $T_2^*$, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of $0.46$% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.

quant-pharXiv:2512.07962•Applied Physics Letters•Dec 10, 2025•11 citations
Abstract To achieve large-scale quantum processors, cryogenic quantum-bit (qubit) interface circuits that can control qubits inside a dilution refrigerator are indispensable. Superconducting single-flux quantum (SFQ) circuits are a promising building block for qubit interface circuits because SFQ circuits can operate with high clock frequencies and low power dissipation. In the present study, we developed an SFQ-based qubit interface circuit that we refer to as a pulse-pair microwave pulse generator (PP-MPG). The PP-MPG can generate microwave pulses for qubit control, with the microwave amplitude controlled based on the delay between paired SFQ pulses. By finely adjusting the delay with delay controlling circuits, the microwave amplitude can be controlled over a wide range. We fabricated a PP-MPG chip and tested it at 4.2 K, showing that the microwave amplitude can be controlled over a range of approximately 30 dB. Our results show that the PP-MPG has the potential for use in future large-scale quantum processors.
In order to control the state of qubits by a microwave pulse, the irradiation time and the amplitude have to be controlled precisely. We have developed a single-flux-quantum (SFQ) microwave chopper for high-speed switching of microwave pulses. The proposed chopper is composed of a DC/SFQ convertor, an SFQ switch, a PTL driver, and a superconducting low-pass filter (LPF). The chopper converts an input microwave, which is generated by an external microwave generator at the room temperature, into microwave pulses by using start/stop SFQ control signals. We designed and implemented a microwave chopper module, which can be attached to dilution refrigerators. SFQ chips were fabricated using the ISTEC 2.5 kA/cm2 Nb process. We tested the microwave chopper module at 4.2 K, and demonstrated that a 5-GHz microwave whose amplitude ranging from 0 μV to 150 μV can be chopped by the SFQ control signals.
An on-chip superconducting microwave pulse generator (MPG), incorporating rapid single-flux-quantum (RSFQ) logic gates and passive radio frequency (RF) components, is an energy-efficient solution for controlling superconducting quantum bits (qubits). Traditional RSFQ MPG designs, however, suffer from a large footprint as multiple RF components (including impedance matching networks, filters, etc.) are separately implemented one after another. In this Letter, we propose a compact on-chip MPG by introducing an integrated RF module. Using a generalized filter synthesis technique, the integrated RF module combines the functionalities of impedance matching and bandpass filtering as a single inductor-capacitor (LC) lumped network. Plenty of circuit elements can, thus, be saved, and the resultant LC network is applicable to both real and complex terminal impedance cases. For validation, a superconducting MPG adopting a fourth-order, 5 GHz centered, 100 MHz bandwidth integrated RF module is designed and fabricated, whose correct operations are confirmed through both simulation and measurement. These results raise the availability of controlling large-scale quantum systems by low-power superconductor technology in the future.
Superconducting qubits are generally controlled by irradiation with microwave pulses. We propose a 5-GHz-range microwave pulse generator based on pulse density modulation for controlling qubits using single-flux-quantum (SFQ) circuits. The proposed microwave pulse generator comprises a 100-GHz circular shift register and a band-pass filter (BPF). In this study, we investigated the relationship between the target envelope of the microwave amplitude and the SFQ pulse density based on the transfer function for the BPF and the frequency spectrum of an SFQ pulse. We implemented a 64-bit circular shift register and demonstrated its operation up to 68 GHz.
Abstract In this study, the on‐chip generation of microwave signals are proposed for controlling nearby quantum bits in a low‐temperature environment, utilizing superconducting logical and RF components. To achieve enhanced amplitude of the microwave, superconducting single flux quantum (SFQ) pulse pairs are employed, which can have either the same or reversal polarity, serving as the basic elements of the generator. The SFQ pulse pairs are then combined and wave‐shaped by using a microwave combining filter, which finally outputs desired microwave signals with narrow line‐width. The amplitude of the microwave signal correlates with the interval between two SFQ pulses in a pair and can be adjusted accordingly. To validate the proposal, test chips are fabricated and performed experiments. The experimental results confirm that the method using a reverse‐polarity pulse can maximize the output microwave amplitude and provide control of the initial phase of the output microwave. This improvement offers a superior alternative for generating microwaves using superconducting circuits to control quantum bits.
Abstract The use of high-frequency input signals from room-temperature microwave sources makes it difficult to scale up the number of quantum bits in universal quantum computers. To address this issue, superconducting single flux quantum (SFQ) integrated circuits are being explored as suitable candidates for qubit manipulation in universal quantum computers. This paper deals with a scalable SFQ qubit control circuit (SQCC) structure that requires only low-frequency input. The circuit mainly consists of a pulse generator and a counter, that output the SFQ pulse train with adjustable frequency and a controllable number of pulses, which is applicable to control single-qubit Clifford operations. The design of low-voltage rapid single flux quantum (LV-RSFQ) and energy-efficient rapid single flux quantum (ERSFQ) for the SQCC achieves low power consumption and provides a basis for scaling up SQCC to control more qubits. The proposed circuits are fabricated under the SIMIT-Nb03 process and successfully pass test verification. The achieved test results reveal that the adjustable output frequency ranges of the SQCC based on the LV-RSFQ and ERSFQ designs in order are [2.40, 8.11] GHz and [4.81, 5.14] GHz. In the operating frequency range, the circuit is able to generate the correct number of SFQ pulses under control. The controllable number range is from 1 to 128. When the circuits operate at 5 GHz, the total power consumptions of the above circuits in order are 23.88 μW and 6.2 μW. All input signals are low-frequency signals, which frees the control of large-scale qubits from limitations caused by high-frequency inputs produced by room-temperature microwave sources.
Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime T1T_1T1​, coherence time T2∗T_2^*T2∗​ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for T1T_1T1​ and T2∗T_2^*T2∗​, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of 0.460.460.46% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.