Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Topical Meeting on Optical Bistability (OB)

Optical Bistability in 1.55 μm Semiconductor Laser Amplifiers

M.J. Adams, H.J. Westlake, M.J. O’Mahony

Published Jan 1, 1985• 0 citations
Publisher

Abstract

Dispersive bistability arising from the carrier-dependence of the refractive index has been observed in semiconductor lasers operated just below threshold with a small injected optical signal. The minimum optical input required for switch-up is as low as 1 μW for InGaAsP amplifiers at 1.55 μm(1) and 1.3 μm(2) (cf 30 μW for GaAs devices(3)). As yet, reliable measurements of the dynamic response are not (4) available, although we predict recovery times to be on the order of carrier lifetimes, ie a few nanoseconds at room temperature. This contribution will review our experimental and theoretical work on 1.55 μm amplifier bistability and set it in the context of other semiconductor bistable optical devices.

DOI
10.1364/obi.1985.wb4

Related papers

Optical bistability measurements on a 1.S- μm semiconductor laser amplifier

H.J. Westlake, Matthew Adams, M.J. O’Mahony

Optical bistability in semiconductor laser amplifiers is particularly interesting because of the gain provided by the device. Small changes, in input power can result in large changes in amplifier gain, and this leads to possible applications in all-optical regenerators for transmission systems. Other possible applications include their use as optical switches and logic elements.1 Optical bistability in GaAs laser amplifiers operating at 850 nm has been reported previously.2 Here we report for the first time measured results at 1.5 μm with an InGaAsP device.

Conference on Lasers and Electro-Optics•Jan 1, 1985•0 citations

Optical bistability in InGaAsP amplifiers and implications for passive devices

Wayne F. Sharfin, M. Dagenais

We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.

Conference on Lasers and Electro-Optics•Jan 1, 1985•0 citations

Room-temperature optical bistability in InGaAsP/InP amplifiers and implications for passive devices

Wayne F. Sharfin, M. Dagenais

Optical bistability has been observed for the first time in a room-temperature InGaAsP/InP amplifier. Switching occurred at an optical input power of about 3 μW, corresponding to a change in the refractive index of 5×10−4. The results are discussed in terms of a light-induced change in carrier concentration. Implications for bistability in passive devices are also discussed.

Applied Physics Letters•May 1, 1985•52 citations

Static and dynamical properties of dispersive optical bistability in semiconductor lasers

Rongqing Hui

Static and dynamic properties of dispersive optical bistability (OB) in semiconductor lasers biased from below to above threshold has been investigated both theoretically and experimentally. The OB result is found to be varied continuously from below to above threshold. Although conventionally the OB switch-off time in dispersive semiconductor laser amplifiers is limited by the effective carrier lifetime, a much faster OB switch-off can be obtained when a laser diode operates well above threshold in the injection-locked condition.>

Journal of Lightwave Technology•Jan 1, 1995•21 citations

Time dependent analysis of active and passive optical bistability in semiconductors

M.J. Adams

A time-dependent theory of optical bistability is developed and applied to laser amplifiers and passive semiconductor etalons. Results of the theory show an output intensity spike in switch-up which occurs after a time delay determined largely by the carrier recombination time, and before which the transition is unstable. Although for passive etalons the spike is rather broad (of order 1 ns for parameters appropriate to GaAs at 0.85 μm or InGaAsP at 1.55 μm) and of low amplitude, for amplifiers it is roughly an order of magnitude narrower and higher in amplitude. As a consequence, it is predicted that clock speeds for semiconductor bistable switching elements will be limited to rates commensurate with the carrier recombination time, not only for switch-down operations (as already well known) but also for switch-up operations.

IEE Proceedings J Optoelectronics•Jan 1, 1985•45 citations

Optical bistability in active distributed—feedback structures: an experimental and theoretical study

Richard R. Wyatt, Mike J. Adams

Optical bistability in active semiconductor devices has attracted considerable interest recently due to the possibility of combining microwatt switching powers with nanosecond switching times. We present experimental and theoretical results of optical bistability in a distributed-feedback (DFB) laser amplifier operating in reflection at 1.5 μm; switch-on delay followed by a sharp transient overshoot is predicted and observed. Minimum switching energies are in the femtojoule region.

Conference on Lasers and Electro-Optics•Jan 1, 1986•4 citations
Dispersive bistability arising from the carrier-dependence of the refractive index has been observed in semiconductor lasers operated just below threshold with a small injected optical signal. The minimum optical input required for switch-up is as low as 1 μW for InGaAsP amplifiers at 1.55 μm(1) and 1.3 μm(2) (cf 30 μW for GaAs devices(3)). As yet, reliable measurements of the dynamic response are not (4) available, although we predict recovery times to be on the order of carrier lifetimes, ie a few nanoseconds at room temperature. This contribution will review our experimental and theoretical work on 1.55 μm amplifier bistability and set it in the context of other semiconductor bistable optical devices.
Optical bistability in semiconductor laser amplifiers is particularly interesting because of the gain provided by the device. Small changes, in input power can result in large changes in amplifier gain, and this leads to possible applications in all-optical regenerators for transmission systems. Other possible applications include their use as optical switches and logic elements.1 Optical bistability in GaAs laser amplifiers operating at 850 nm has been reported previously.2 Here we report for the first time measured results at 1.5 μm with an InGaAsP device.
We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.
Static and dynamic properties of dispersive optical bistability (OB) in semiconductor lasers biased from below to above threshold has been investigated both theoretically and experimentally. The OB result is found to be varied continuously from below to above threshold. Although conventionally the OB switch-off time in dispersive semiconductor laser amplifiers is limited by the effective carrier lifetime, a much faster OB switch-off can be obtained when a laser diode operates well above threshold in the injection-locked condition.>
A time-dependent theory of optical bistability is developed and applied to laser amplifiers and passive semiconductor etalons. Results of the theory show an output intensity spike in switch-up which occurs after a time delay determined largely by the carrier recombination time, and before which the transition is unstable. Although for passive etalons the spike is rather broad (of order 1 ns for parameters appropriate to GaAs at 0.85 μm or InGaAsP at 1.55 μm) and of low amplitude, for amplifiers it is roughly an order of magnitude narrower and higher in amplitude. As a consequence, it is predicted that clock speeds for semiconductor bistable switching elements will be limited to rates commensurate with the carrier recombination time, not only for switch-down operations (as already well known) but also for switch-up operations.