Annual Meeting Optical Society of America

n2 measurements through the inverse transmittance in a bistable laser diode

Riccardo A. Calvani, Renato Caponi

Published Jan 1, 1990• 0 citations

Abstract

The optical parameters (in particular the nonlinear refractive index n2) of a bistable Fabry–Perot (FP) amplifier pumped by a similar GaAlAs laser have been evaluated from the optical bistability (OB) cycle of the operating device.1 This paper presents a new n2 measurement method, utilizing the same OB data through a linear fit of the single pass FP phase Φ.

DOI: 10.1364/oam.1990.wm5

Related papers

Measurement of the nonlinear refractive index in a bistable laser diode

Riccardo Calvani, Renato Caponi

The optical bistability (OB) behavior of a semiconductor Fabry-Perot (F.P.) cavity, biased around threshold, has been employed to evaluate the optical device parameters.1 In the present work, this approach was experimentally applied to measurements of the nonlinear refractive-index coefficient n2 in OB operating conditions.

Annual Meeting Optical Society of AmericaJan 1, 19880 citations

Switching power dependence on detuning and current in bistable diode laser amplifiers

Zeqi Pan, Hongchin Lin, M. Dagenais

Measurements of the optical power required to switch on-and-off an optical bistable diode laser amplifier as a function of detuning and current from threshold are presented. Good quantitative agreement between the theory for a nonlinear Fabry–Perot and the experimental results are obtained. A linewidth enhancement factor of 3.1 and a value for the change of the refractive index versus carrier density of −1.8×10−20 cm3 are extracted from the measurements.

Applied Physics LettersFeb 18, 199130 citations

Optical Bistability of an Injection-Locked Single-Mode Fabry-Perot Laser Diode and Its Application to an Optical Filp-Flop

Jeong Sik Cho, Nguyen le Hoang, Yong Deok Jeong +1 more

We investigate optical bistability of an injection-locked single-mode Fabry-Perot laser diode. Normal and reversed optical bistability curves are observed from the injection-locked laser. And the inverse bistability is used to implement an all-optical flip-flop with the high on-off ratio of over 35 dB.

Conference on Lasers and Electro-Optics Pacific Rim (CLEO-PR)Aug 1, 20072 citations

Optical bistability in InGaAsP amplifiers and implications for passive devices

Wayne F. Sharfin, M. Dagenais

We demonstrate optically bistable (light switching light) operation in a room-temperature InGaAsP Fabry-Perot amplifier. The amplifier is an InGaAsP/InP laser structure biased at ~95% of its lasing threshold. It is switched with <3 μW of optical power provided by the mechanically chopped output of a quasi-single-mode InGaAsP/InP laser. The experimental apparatus is depicted in Fig, 1. A change in the refractive Index in the amplifier of only 5 × 10−4 is sufficient to cause switching. Input and output pulses from the nonlinear amplifier are shown in Fig. 2 when the source frequency is initially detuned by 14 GHz from the closest Fabry-Perot mode of the amplifier. Smaller switching powers are required at lesser detunings. The physical mechanism of the intensity-dependent change of the refractive index is thought to be the change in carrier density resulting from stimulated recombination of free carriers.

Conference on Lasers and Electro-OpticsJan 1, 19850 citations

Optical Bistability

Guang S. He

When the output parameter of an optical device could be a multivalued function of the input parameter, this device can be working in an optical bistable status. The most typical optical bistable device is a Fabry–Perot cavity containing a nonlinear optical medium, the refractive index of which depends on the light intensity. Upon the action of an intense input optical beam, the transmitted (or reflected) intensity of this device may exhibit a nonlinear response to the incident light intensity variation and, especially under appropriate working conditions, the characteristic output/input curve may manifest a single (or multiple) hysteresis loop(s). Such type of optical bistable device can be used as an optical differential amplifier, optical switch, optical limiter, optical clipper, optical discriminator, or an optical memory element, depending on the chosen nonlinear medium and operation conditions.

Oxford University Press eBooksOct 30, 20141 citation

Reflective bistability in 1.55 μm laser diode amplifiers

Paradorn Pakdeevanich, M.J. Adams

Bistable laser amplifiers are attractive for potential application in optical switching because of very low input optical requirement, high extinction ratio and the presence of optical gain. Optical bistability (OB) arises from gain saturation and the associated nonlinear refraction combined with the effect of feedback in the laser cavity. We present the experimental results of bistable characteristics for the case of a 1.55 /spl mu/m symmetric Fabry-Perot (F-P) laser amplifier with uncoated facets. This paper reports a particularly rich variety of behaviour for reflected signals. Three main forms of hysteresis loops are observed on reflection. The hysteresis loop changes from anticlockwise to clockwise hysteresis in the optical input-output characteristic when the drive current or initial phase detuning is changed. The butterfly hysteresis loop is observed experimentally at optical input power as low as 260 /spl mu/W for a drive current equal to 90% of the lasing threshold. The dependence of the optical bistability on drive current, initial phase detuning and injected optical power has been investigated. In the bistable light output-initial phase detuning characteristic, the optimum frequency is shifted downward with an increase in the injected power or the drive current. All measurements are in good agreement with an analytical model.

Jan 1, 19980 citations