Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.
We experimentally demonstrate an improved optical biasing scheme for superconducting nanowire single-photon detectors (SNSPDs), which employs a cryogenic InGaAs-InP photodiode (PD) as a local bias source. It is found that, under illumination from a stable external light source, this PD generates a stable photocurrent in a cryogenic environment (~2.3 K), with fluctuations in the photocurrent primarily attributed to fluctuations in the incident optical power. Furthermore, by screening and effectively blocking stray photons leaking from the PD, which give rise to background dark counts, we have achieved an SNSPD exhibiting an ultra-low intrinsic dark count rate of 1e-4 cps. Utilizing this improved optical biasing technique, our SNSPD achieved performance comparable to that obtained under conventional electrical biasing: a system detection efficiency of 80.7%, a background dark count rate of 32.6 cps, and a minimum timing jitter of 57.5 ps. These results indicate that cryogenic-PD-based optical biasing serves as a viable, low-noise, and low-jitter alternative to traditional electrical biasing. Moreover, this work offers useful design guidance for the future development of PD-based low-noise bias sources and for the construction of all-photonic SNSPD systems tailored for high-precision quantum photonics applications.
Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.
Cryogenic opto-electronic interconnects are gaining increasing interest as a means to control and read out cryogenic electronic components. The challenge is to achieve sufficient signal integrity with low heat load processing. In this context, we demonstrate the opto-electronic bias and readout of a commercial four-pixel superconducting nanowire single-photon detector array using a cryogenic photodiode and laser. We show that this approach has a similar system detection efficiency to a conventional bias. Furthermore, multi-pixel detection events are faithfully converted between the optical and electrical domain, which allows reliable extraction of amplitude multiplexed photon statistics. Our device has a passive heat dissipation of 2.6mW, maintains the signal rise time of 3ns, and operates in free-running (self-resetting) mode at a repetition rate of 600kHz. This demonstrates the potential of high-bandwidth, low noise, and low heat load opto-electronic interconnects for scalable cryogenic signal processing and transmission.
Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm
2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500
Ω with a low power dissipation of 40
μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.
Scalable, low power, high speed data transfer between cryogenic and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and allows for very high bandwidth densities by carrying multiple signals through the same physical fiber. By operating a CMOS modulator in the forward bias regime at a temperature of 3.6 K, we have demonstrated the optical readout of a superconducting nanowire single-photon detector (SNSPD) without the need for an interfacing device.