Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Advanced Photon Counting Techniques

Photonic readout of superconducting nanowire single photon counting detectors

Rajeev J. Ram, Marc de, Emma E. Wollman, Matthew D. Shaw

Published Jun 15, 2023• 0 citations
Publisher

Abstract

Scalable, low power, high speed data transfer between cryogenic and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and allows for very high bandwidth densities by carrying multiple signals through the same physical fiber. By operating a CMOS modulator in the forward bias regime at a temperature of 3.6 K, we have demonstrated the optical readout of a superconducting nanowire single-photon detector (SNSPD) without the need for an interfacing device.

DOI
10.1117/12.2663806

Related papers

Photonic Readout of Superconducting Nanowire Single Photon Counting Detectors

Marc de, Emma E. Wollman, Amir Hossein Atabaki +3 more

Abstract Scalable, low power, high speed data transfer between cryogenic (0.1–4 K) and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1,000–10,000 pm/V) and a low input impedance of 500 Ω with a low power dissipation of 40 μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD.

Scientific Reports•Jun 11, 2020•40 citations

Readout of Superconducting Nanowire Single Photon Detectors through Forward Biased Optical Modulators

Marc de, Emma E. Wollman, Amir Hossein Atabaki +3 more

Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm$^2$ range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500 $Ω$ with a low power dissipation of 40 $μ$W. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.

arXiv:2002.00063•Jan 29, 2020•4 citations

Characterizing All-Optical Biasing and Readout of a Superconducting Opto-Electronic Circuit

Frederik Thiele, Thomas R. Hummel, Julian Brockmeier +6 more

Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 26, 2023•0 citations

All optical operation of a superconducting photonic interface

Frederik Thiele, Thomas R. Hummel, Adam N. McCaughan +7 more

Quantum photonic processing via electro-optic components typically requires electronic links across different operation environments, especially when interfacing cryogenic components such as superconducting single photon detectors with room-temperature control and readout electronics. However, readout and driving electronics can introduce detrimental parasitic effects. Here we show an all-optical control and readout of a superconducting nanowire single photon detector (SNSPD), completely electrically decoupled from room temperature electronics. We provide the operation power for the superconducting detector via a cryogenic photodiode, and readout single photon detection signals via a cryogenic electro-optic modulator in the same cryostat. This method opens the possibility for control and readout of superconducting circuits, and feedforward for photonic quantum computing.

Optics Express•Aug 29, 2023•13 citations

Opto-electronic bias of a superconducting nanowire single photon detector using a cryogenic photodiode

Frederik Thiele, Thomas Hummel, Maximilian Protte +1 more

Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.

APL Photonics•Aug 1, 2022•9 citations

Scalable cryogenic readout circuit for a superconducting nanowire single-photon detector system

Clinton Cahall, Daniel J. Gauthier, Jungsang Kim

The superconducting nanowire single-photon detector (SNSPD) is a leading technology for quantum information science applications using photons, and is finding increasing uses in photon-starved classical imaging applications. Critical detector characteristics, such as timing resolution (jitter), reset time, and maximum count rate, are heavily influenced by the readout electronics that sense and amplify the photon detection signal. We describe a readout circuit for SNSPDs using commercial off-the-shelf amplifiers operating at cryogenic temperatures. Our design demonstrates a 35 ps timing resolution and a maximum count rate of over 2 × 107 counts per second, while maintaining <3 mW power consumption per channel, making it suitable for a multichannel readout.

arXiv:1710.04684•Review of Scientific Instruments•Jun 1, 2018•28 citations
Scalable, low power, high speed data transfer between cryogenic and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and allows for very high bandwidth densities by carrying multiple signals through the same physical fiber. By operating a CMOS modulator in the forward bias regime at a temperature of 3.6 K, we have demonstrated the optical readout of a superconducting nanowire single-photon detector (SNSPD) without the need for an interfacing device.
Abstract Scalable, low power, high speed data transfer between cryogenic (0.1–4 K) and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1,000–10,000 pm/V) and a low input impedance of 500 Ω with a low power dissipation of 40 μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD.
Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2^22 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500 ΩΩΩ with a low power dissipation of 40 μμμW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.
Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.
Quantum photonic processing via electro-optic components typically requires electronic links across different operation environments, especially when interfacing cryogenic components such as superconducting single photon detectors with room-temperature control and readout electronics. However, readout and driving electronics can introduce detrimental parasitic effects. Here we show an all-optical control and readout of a superconducting nanowire single photon detector (SNSPD), completely electrically decoupled from room temperature electronics. We provide the operation power for the superconducting detector via a cryogenic photodiode, and readout single photon detection signals via a cryogenic electro-optic modulator in the same cryostat. This method opens the possibility for control and readout of superconducting circuits, and feedforward for photonic quantum computing.
Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.
The superconducting nanowire single-photon detector (SNSPD) is a leading technology for quantum information science applications using photons, and is finding increasing uses in photon-starved classical imaging applications. Critical detector characteristics, such as timing resolution (jitter), reset time, and maximum count rate, are heavily influenced by the readout electronics that sense and amplify the photon detection signal. We describe a readout circuit for SNSPDs using commercial off-the-shelf amplifiers operating at cryogenic temperatures. Our design demonstrates a 35 ps timing resolution and a maximum count rate of over 2 × 107 counts per second, while maintaining <3 mW power consumption per channel, making it suitable for a multichannel readout.