Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE MTT-S International Microwave Symposium digest

Measurement Techniques for Superconducting Microwave Resonators Towards Quantum Device Applications

Corey Rae McRae

Published Jun 19, 2022• 3 citations
Publisher

Abstract

Superconducting qubits, though promising for both near-term problem-solving as well as the development of large-scale quantum computing systems, are limited in performance largely by materials-induced decoherence channels which are maximized at millikelvin temperatures, single photon powers, and microwave frequencies. Superconducting microwave resonators are ideal tools for measuring these materials losses due to their simplicity, well-understood behavior, and sensitivity to these same losses. In order to better understand and mitigate dominant qubit decoherence channels, accurate and precise characterization of superconducting microwave resonator performance is critical. In this paper, current measurement techniques for superconducting microwave resonators are discussed, including experimental set-up, error analysis, and cryogenic calibration of a vector network analyzer.

DOI
10.1109/ims37962.2022.9865517

Related papers

Materials loss measurements using superconducting microwave resonators

C. R. H. McRae, H. Wang, J. Gao +5 more

The performance of superconducting circuits for quantum computing is limited by materials losses. In particular, coherence times are typically bounded by two-level system (TLS) losses at single photon powers and millikelvin temperatures. The identification of low loss fabrication techniques, materials, and thin film dielectrics is critical to achieving scalable architectures for superconducting quantum computing. Superconducting microwave resonators provide a convenient qubit proxy for assessing performance and studying TLS loss and other mechanisms relevant to superconducting circuits such as non-equilibrium quasiparticles and magnetic flux vortices. In this review article, we provide an overview of considerations for designing accurate resonator experiments to characterize loss, including applicable types of losses, cryogenic setup, device design, and methods for extracting material and interface losses, summarizing techniques that have been evolving for over two decades. Results from measurements of a wide variety of materials and processes are also summarized. Finally, we present recommendations for the reporting of loss data from superconducting microwave resonators to facilitate materials comparisons across the field.

arXiv:2006.04718•Review of Scientific Instruments•Sep 1, 2020•257 citations

Cryogenic single-port calibration for superconducting microwave resonator measurements

H. Wang, Suren Singh, Corey Rae McRae +8 more

Abstract Superconducting circuit testing and materials loss characterization requires robust and reliable methods for the extraction of internal and coupling quality factors of microwave resonators. A common method, imposed by limitations on the device design or experimental configuration, is the single-port reflection geometry, i.e. reflection-mode. However, impedance mismatches in cryogenic systems must be accounted for through calibration of the measurement chain while it is at low temperatures. In this paper, we demonstrate a data-based, single-port calibration using commercial microwave standards and a vector network analyzer with samples at millikelvin temperature in a dilution refrigerator, making this method useful for measurements of quantum phenomena. Finally, we cross reference our data-based, single-port calibration and reflection measurement with over-coupled 2D- and 3D-resonators against well established two-port techniques corroborating the validity of our method.

arXiv:2103.01491•Quantum Science and Technology•Jun 1, 2021•34 citations

A brief review on recent developments of superconducting microwave resonators for quantum device application

Yonuk Chong

Quantum information processing using superconducting qubit based on Josephson junction has become one of the most promising candidates for possible realization of a quantum computer. In the heart of the qubit circuits, the superconducting microwave resonator plays a key role in quantum operations and measurements, which enables single-photon level microwave quantum optics. During last decade, the coherence time, or the lifetime of the quantum state, of the superconducting qubit has been dramatically improved. Among several technological innovations, the improvement of superconducting microwave resonator's quality has been the main driving force in getting the qubit performance almost ready for elementary quantum computing architecture. In this paper, I will briefly review very recent progresses of the superconducting microwave resonators especially aimed for quantum device applications during the last decade. The progresses have been driven by ingenious circuit design, material improvement, and new measurement techniques. Even a rather radical idea of three-dimensional large resonators have been successfully implemented in a qubit circuit. All those efforts contributed to our understanding of the qubit decoherence mechanism and as a result to the improvement of qubit performance.

Progress in Superconductivity and Cryogenics•Dec 31, 2014•0 citations

Low-temperature characterization of dielectric loss at microwave frequencies in aluminum oxide

Martin R. Otto

Superconducting quantum devices have gained increasing interest over the past 15 years because of their role as promising candidates for implementing a large-scale quantum computer and as ultra-sensitive detectors. Superconducting resonators are one type of superconducting device which are used in a variety of applications including quantum computing and radioastronomy. They can achieve large quality factors which are important for these applications and a variety of others. Specific examples of these applications include the readout and coupling of superconducting qubits and also microwave kinetic inductance detector arrays for sub-mm wavelength astronomical measurements. High quality factors also enable the study of very subtle features in the electromagnetic response of the resonator. This feature in turn offers provides a method to characterize loss mechanisms which affect the performance of superconducting qubits, by measuring the quality factor of a resonator. Dielectric loss is an example of such a loss mechanism, and is considered to be one of, if not \\it the \\rm major obstacle to overcome in order to construct scalable quantum technologies based on superconducting devices. This type of loss arises from the coupling of the electric field in the device to spurious degrees of freedom which arise naturally the dielectric environment of the device. The fast-growing interest in the physics and applications of superconducting resonators has renewed interest in an improving our fundamental understanding of dielectric loss. This interest involves the study of a much bigger and older question in condensed matter physics; namely, what is the microscopic physics which governs the behaviour and of an amorphous material at low-temperatures? \n \nIn this thesis, we present a systematic study of dielectric loss in amorphous aluminum oxide using superconducting microwave resonators. Measurements of the intrinsic loss tangent over a large temperature range of 40~mK to 1~K are presented and analyzed in detail. Some aspects of the data are well understood in terms of the standard tunnelling two-level system model, while others require a deeper analysis of the electrodynamics of the resonator and insights from more advanced theories. We employ a consistent approach using numerical simulations of the resonator to understand loss mechanisms arising from both an inhomogeneous electric field and multiple dielectric layers. We measure saturation effects which provide insight into coherent properties of two-level system ensembles and the mutual interaction between them. Excellent agreement with the two-level system model is found for intrinsic losses, however the strong dependence on temperature which we observe for saturation effects is not predicted in the standard form of the model. We find that this dependence can be understood in terms of the theory of spectral diffusion which is consistent with a strong mutual interaction between two-level systems contributes to broadening of their spectral linewidths.

•Apr 9, 2015•1 citation

Fabrication and Characterization of Superconducting Resonators

Giuseppe Cataldo, Emily M. Barrentine, Ari-David Brown +3 more

Superconducting microwave resonators are of interest for a wide range of applications, including for their use as microwave kinetic inductance detectors (MKIDs) for the detection of faint astrophysical signatures, as well as for quantum computing applications and materials characterization. In this paper, procedures are presented for the fabrication and characterization of thin-film superconducting microwave resonators. The fabrication methodology allows for the realization of superconducting transmission-line resonators with features on both sides of an atomically smooth single-crystal silicon dielectric. This work describes the procedure for the installation of resonator devices into a cryogenic microwave testbed and for cool-down below the superconducting transition temperature. The set-up of the cryogenic microwave testbed allows one to do careful measurements of the complex microwave transmission of these resonator devices, enabling the extraction of the properties of the superconducting lines and dielectric substrate (e.g., internal quality factors, loss and kinetic inductance fractions), which are important for device design and performance.

Journal of Visualized Experiments•May 21, 2016•3 citations

Fabrication and Characterization of Superconducting Resonators

Giuseppe Cataldo, Emily M. Barrentine, Ari-David Brown +3 more

Superconducting microwave resonators are of interest for a wide range of applications, including for their use as microwave kinetic inductance detectors (MKIDs) for the detection of faint astrophysical signatures, as well as for quantum computing applications and materials characterization. In this paper, procedures are presented for the fabrication and characterization of thin-film superconducting microwave resonators. The fabrication methodology allows for the realization of superconducting transmission-line resonators with features on both sides of an atomically smooth single-crystal silicon dielectric. This work describes the procedure for the installation of resonator devices into a cryogenic microwave testbed and for cool-down below the superconducting transition temperature. The set-up of the cryogenic microwave testbed allows one to do careful measurements of the complex microwave transmission of these resonator devices, enabling the extraction of the properties of the superconducting lines and dielectric substrate (e.g., internal quality factors, loss and kinetic inductance fractions), which are important for device design and performance.

Journal of Visualized Experiments•May 21, 2016•1 citation
Superconducting qubits, though promising for both near-term problem-solving as well as the development of large-scale quantum computing systems, are limited in performance largely by materials-induced decoherence channels which are maximized at millikelvin temperatures, single photon powers, and microwave frequencies. Superconducting microwave resonators are ideal tools for measuring these materials losses due to their simplicity, well-understood behavior, and sensitivity to these same losses. In order to better understand and mitigate dominant qubit decoherence channels, accurate and precise characterization of superconducting microwave resonator performance is critical. In this paper, current measurement techniques for superconducting microwave resonators are discussed, including experimental set-up, error analysis, and cryogenic calibration of a vector network analyzer.
The performance of superconducting circuits for quantum computing is limited by materials losses. In particular, coherence times are typically bounded by two-level system (TLS) losses at single photon powers and millikelvin temperatures. The identification of low loss fabrication techniques, materials, and thin film dielectrics is critical to achieving scalable architectures for superconducting quantum computing. Superconducting microwave resonators provide a convenient qubit proxy for assessing performance and studying TLS loss and other mechanisms relevant to superconducting circuits such as non-equilibrium quasiparticles and magnetic flux vortices. In this review article, we provide an overview of considerations for designing accurate resonator experiments to characterize loss, including applicable types of losses, cryogenic setup, device design, and methods for extracting material and interface losses, summarizing techniques that have been evolving for over two decades. Results from measurements of a wide variety of materials and processes are also summarized. Finally, we present recommendations for the reporting of loss data from superconducting microwave resonators to facilitate materials comparisons across the field.
Abstract Superconducting circuit testing and materials loss characterization requires robust and reliable methods for the extraction of internal and coupling quality factors of microwave resonators. A common method, imposed by limitations on the device design or experimental configuration, is the single-port reflection geometry, i.e. reflection-mode. However, impedance mismatches in cryogenic systems must be accounted for through calibration of the measurement chain while it is at low temperatures. In this paper, we demonstrate a data-based, single-port calibration using commercial microwave standards and a vector network analyzer with samples at millikelvin temperature in a dilution refrigerator, making this method useful for measurements of quantum phenomena. Finally, we cross reference our data-based, single-port calibration and reflection measurement with over-coupled 2D- and 3D-resonators against well established two-port techniques corroborating the validity of our method.
Quantum information processing using superconducting qubit based on Josephson junction has become one of the most promising candidates for possible realization of a quantum computer. In the heart of the qubit circuits, the superconducting microwave resonator plays a key role in quantum operations and measurements, which enables single-photon level microwave quantum optics. During last decade, the coherence time, or the lifetime of the quantum state, of the superconducting qubit has been dramatically improved. Among several technological innovations, the improvement of superconducting microwave resonator's quality has been the main driving force in getting the qubit performance almost ready for elementary quantum computing architecture. In this paper, I will briefly review very recent progresses of the superconducting microwave resonators especially aimed for quantum device applications during the last decade. The progresses have been driven by ingenious circuit design, material improvement, and new measurement techniques. Even a rather radical idea of three-dimensional large resonators have been successfully implemented in a qubit circuit. All those efforts contributed to our understanding of the qubit decoherence mechanism and as a result to the improvement of qubit performance.
Superconducting quantum devices have gained increasing interest over the past 15 years because of their role as promising candidates for implementing a large-scale quantum computer and as ultra-sensitive detectors. Superconducting resonators are one type of superconducting device which are used in a variety of applications including quantum computing and radioastronomy. They can achieve large quality factors which are important for these applications and a variety of others. Specific examples of these applications include the readout and coupling of superconducting qubits and also microwave kinetic inductance detector arrays for sub-mm wavelength astronomical measurements. High quality factors also enable the study of very subtle features in the electromagnetic response of the resonator. This feature in turn offers provides a method to characterize loss mechanisms which affect the performance of superconducting qubits, by measuring the quality factor of a resonator. Dielectric loss is an example of such a loss mechanism, and is considered to be one of, if not \\it the \\rm major obstacle to overcome in order to construct scalable quantum technologies based on superconducting devices. This type of loss arises from the coupling of the electric field in the device to spurious degrees of freedom which arise naturally the dielectric environment of the device. The fast-growing interest in the physics and applications of superconducting resonators has renewed interest in an improving our fundamental understanding of dielectric loss. This interest involves the study of a much bigger and older question in condensed matter physics; namely, what is the microscopic physics which governs the behaviour and of an amorphous material at low-temperatures? \n \nIn this thesis, we present a systematic study of dielectric loss in amorphous aluminum oxide using superconducting microwave resonators. Measurements of the intrinsic loss tangent over a large temperature range of 40~mK to 1~K are presented and analyzed in detail. Some aspects of the data are well understood in terms of the standard tunnelling two-level system model, while others require a deeper analysis of the electrodynamics of the resonator and insights from more advanced theories. We employ a consistent approach using numerical simulations of the resonator to understand loss mechanisms arising from both an inhomogeneous electric field and multiple dielectric layers. We measure saturation effects which provide insight into coherent properties of two-level system ensembles and the mutual interaction between them. Excellent agreement with the two-level system model is found for intrinsic losses, however the strong dependence on temperature which we observe for saturation effects is not predicted in the standard form of the model. We find that this dependence can be understood in terms of the theory of spectral diffusion which is consistent with a strong mutual interaction between two-level systems contributes to broadening of their spectral linewidths.
Superconducting microwave resonators are of interest for a wide range of applications, including for their use as microwave kinetic inductance detectors (MKIDs) for the detection of faint astrophysical signatures, as well as for quantum computing applications and materials characterization. In this paper, procedures are presented for the fabrication and characterization of thin-film superconducting microwave resonators. The fabrication methodology allows for the realization of superconducting transmission-line resonators with features on both sides of an atomically smooth single-crystal silicon dielectric. This work describes the procedure for the installation of resonator devices into a cryogenic microwave testbed and for cool-down below the superconducting transition temperature. The set-up of the cryogenic microwave testbed allows one to do careful measurements of the complex microwave transmission of these resonator devices, enabling the extraction of the properties of the superconducting lines and dielectric substrate (e.g., internal quality factors, loss and kinetic inductance fractions), which are important for device design and performance.
Superconducting microwave resonators are of interest for a wide range of applications, including for their use as microwave kinetic inductance detectors (MKIDs) for the detection of faint astrophysical signatures, as well as for quantum computing applications and materials characterization. In this paper, procedures are presented for the fabrication and characterization of thin-film superconducting microwave resonators. The fabrication methodology allows for the realization of superconducting transmission-line resonators with features on both sides of an atomically smooth single-crystal silicon dielectric. This work describes the procedure for the installation of resonator devices into a cryogenic microwave testbed and for cool-down below the superconducting transition temperature. The set-up of the cryogenic microwave testbed allows one to do careful measurements of the complex microwave transmission of these resonator devices, enabling the extraction of the properties of the superconducting lines and dielectric substrate (e.g., internal quality factors, loss and kinetic inductance fractions), which are important for device design and performance.