Large-Area Superconducting Nanowire Single-Photon Detectors for Operation at Wavelengths up to 7.4 μm
Marco Colangelo, Alexander B. Walter, Boris A. Korzh, Ekkehart Schmidt, Bruce Bumble, Adriana E. Lita, Andrew D. Beyer, Jason P. Allmaras, Ryan M. Briggs, Alexander G. Kozorezov, Emma E. Wollman, Matthew D. Shaw, Karl K. Berggren
The optimization of superconducting thin-films has pushed the sensitivity of superconducting nanowire single-photon detectors (SNSPDs) to the mid-infrared (mid-IR). Earlier demonstrations have shown that straight tungsten silicide nanowires can achieve unity internal detection efficiency (IDE) up to λ = 10 μm. For a high system detection efficiency (SDE), the active area needs to be increased, but material nonuniformity and nanofabrication-induced constrictions make mid-IR large-area meanders challenging to yield. In this work, we improve the sensitivity of superconducting materials and optimize a high-resolution nanofabrication process to demonstrate large-area SNSPDs with unity IDE at 7.4 μm. Our approach yields large-area meanders down to 50 nm width, with average line-width roughness below 10%, and with a lower impact from constrictions compared to previous demonstrations. Our methods pave the way to high-efficiency SNSPDs in the mid-IR band with potential impacts on astronomy, imaging, and physical chemistry.
The optimization of superconducting thin-films has pushed the sensitivity of superconducting nanowire single-photon detectors (SNSPDs) to the mid-infrared (mid-IR). Earlier demonstrations have shown that straight tungsten silicide nanowires can achieve unity internal detection efficiency (IDE) up to λ = 10 μm. For a high system detection efficiency (SDE), the active area needs to be increased, but material nonuniformity and nanofabrication-induced constrictions make mid-IR large-area meanders challenging to yield. In this work, we improve the sensitivity of superconducting materials and optimize a high-resolution nanofabrication process to demonstrate large-area SNSPDs with unity IDE at 7.4 μm. Our approach yields large-area meanders down to 50 nm width, with average line-width roughness below 10%, and with a lower impact from constrictions compared to previous demonstrations. Our methods pave the way to high-efficiency SNSPDs in the mid-IR band with potential impacts on astronomy, imaging, and physical chemistry.
Superconducting nanowire single-photon detectors (SNSPDs) are among the most sensitive single-photon detectors available and have the potential to transform fields ranging from infrared astrophysics to molecular spectroscopy. However, extending their performance into the mid-infrared spectral region - crucial for applications such as exoplanet transit spectroscopy and vibrational fingerprinting of molecules - has remained a major challenge, primarily due to material limitations and scalability constraints. Here, we report on the development of SNSPDs based on tungsten germanide, a novel material system that combines high mid-infrared sensitivity with compatibility for large-scale fabrication. Our detectors exhibit saturated internal detection efficiency at wavelengths up to 29 μm, while using 2.7x thicker films (8 nm vs 3 nm) and up to 4.5x wider nanowires (360 nm vs 80 nm) compared to mid-infrared-optimized SNSPDs fabricated from tungsten silicide. This advance will enable scalable, high-performance single-photon detection in a spectral region that was previously inaccessible, opening new frontiers in remote sensing, thermal imaging, environmental monitoring, molecular physics, and astronomy.
Mid-infrared (MIR) single-photon detection is emerging as an important technology for various applications. Superconducting nanowire single photon detectors (SNSPDs) fabricated with superconducting films with energy gaps of a few meV are natural broadband single-photon detectors. Recently, extending SNSPDs’ operation wavelengths into the MIR region is highly attractive. γ-Nb4N3 has a reduced N content and lower energy gap than the commonly used δ-NbN, making SNSPDs based on γ-Nb4N3 film more sensitive to low energy photons. We report on a Nb4N3-SNSPD based on 62-nm wide nanowire, with an optical absorption enhancement design and an optimized device package for efficient ZBLAN fiber coupling and dark count filtering. The developed device has a unity intrinsic detection efficiency (IDE) in the 1.5–4 µm wavelength region, and the device detection efficiency at 2.95 µm was measured to be 32.5%, with an uncertainty of 12.7%. Furthermore, we reduced the device geometry, and measured 3–10 µm photon response of a device based on 5-nm film and 42-nm nanowire, with an IDE of 95%, 81%, 40%, and 6% for 4.8, 6, 8, and 10 µm, respectively.
Shortly after their inception, superconducting nanowire single-photon detectors (SNSPDs) became the leading quantum light detection technology. With the capability of detecting single-photons with near-unity efficiency, high time resolution, low dark count rate, and fast recovery time, SNSPDs outperform conventional single-photon detection techniques. However, detecting lower energy single photons ( < 0.8 eV ) with high efficiency and low timing jitter has remained a challenge. To achieve unity internal efficiency at mid-infrared wavelengths, previous works used amorphous superconducting materials with low energy gaps at the expense of reduced time resolution (close to a nanosecond), and by operating them in complex milliKelvin (mK) dilution refrigerators. In this work, we provide an alternative approach with SNSPDs fabricated from 5 to 9.5 nm thick NbTiN superconducting films and devices operated in conventional Gifford-McMahon cryocoolers. By optimizing the superconducting film deposition process, film thickness, and nanowire design, our fiber-coupled devices achieved > 70 % system detection efficiency (SDE) at 2 μm and sub-15 ps timing jitter. Furthermore, detectors from the same batch demonstrated unity internal detection efficiency at 3 μm and 80% internal efficiency at 4 μm, paving the road for an efficient mid-infrared single-photon detection technology with unparalleled time resolution and without mK cooling requirements. We also systematically studied the dark count rates (DCRs) of our detectors coupled to different types of mid-infrared optical fibers and blackbody radiation filters. This offers insight into the trade-off between bandwidth and DCRs for mid-infrared SNSPDs. To conclude, this paper significantly extends the working wavelength range for SNSPDs made from polycrystalline NbTiN to 1.5–4 μm, and we expect quantum optics experiments and applications in the mid-infrared range to benefit from this far-reaching technology.
Abstract The advancement of superconducting nanowire single-photon detectors (SNSPDs or SSPDs) is intrinsically linked to breakthroughs in superconducting materials engineering. These detectors are prized for their excellent sensitivity and performance across a wide wavelength range, from ultra-violet to mid-infrared (mid-IR). Plasma-enhanced atomic layer deposition (ALD) is an advanced deposition technique that enables exceptional film uniformity across large wafers, making it ideal for a variety of applications. In this study, ALD NbTiN films are fabricated into SNSPDs that exhibit single-photon response across near- to mid-IR wavelengths. A 5 nm thick NbTiN film was patterned into devices consisting of ∼100 nm wide meandered nanowires, and the nanowire cross-section and composition were analysed by transmission electron microscopy. The devices were tested in a closed-cycle cryostat with a base temperature of 0.9 K. Photon detection rate and timing jitter were measured across the wavelength range 1.5–4.4 µ m under low dark count conditions, confirming single-photon sensitivity across the measured wavelength bands. This work introduces the ALD-grown NbTiN films as a new platform for SNSPD detectors, achieving mid-IR single-photon sensitivity. The intact film quality after fabrication demonstrates the potential of ALD processes for scalable infrared detector technologies.
Shortly after their inception, superconducting nanowire single-photon detectors (SNSPDs) became the leading quantum light detection technology. With the capability of detecting single-photons with near-unity efficiency, high time resolution, low dark count rate, and fast recovery time, SNSPDs outperform conventional single-photon detection techniques. However, detecting lower energy single-photons (<0.8 eV) with high efficiency and low timing jitter has remained a challenge. To achieve unity internal efficiency at mid-infrared wavelengths, previous works used amorphous superconducting materials with low energy gaps at the expense of reduced time resolution (close to a nanosecond), and by operating them in complex mK dilution refrigerators. In this work, we provide an alternative approach with SNSPDs fabricated from 5-9.5 nm thick NbTiN superconducting films and devices operated in conventional Gifford-McMahon (GM) cryocoolers. By optimizing the superconducting film deposition process, film thickness and nanowire design, our fiber-coupled devices achieved > 70% system detection efficiency (SDE) at 2 μm and sub-15 ps timing jitter. Furthermore, detectors from the same batch demonstrated unity internal detection efficiency at 3 μm and 80% internal efficiency at 4 μm, paving the road for an efficient mid-infrared single-photon detection technology with unparalleled time resolution and without mK cooling requirements.