One of the key issues when dealing with slow light is the inevitable effect of dispersion, the result of which is to broaden a pulse upon propagation. Moreover, the dispersion tends to increase when the group velocity, the speed at which the pulse propagates, decreases. To see this, we note that if we write the group velocity vg ≡ c/ng, where ng is the group index, then we find that ng = n+ωdn/dω. Since for the materials we are interested in, the refractive index does not vary strongly in magnitude, and slow light is obtained when the derivative dn/dω is large and positive. However, as the variations in the magnitude of n itself are limited, the large derivative can only be maintained over a narrow bandwidth ∝ (dn/dω)−1. Therefore, a large delay implies a narrow bandwidth, and hence a limited pulse width. Here we discuss how to avoid this limit by using nonlinear effects in the form of gap solitons. Though this argument is quite simple, it can be made rigorous using the Kramers-Kronig relations. In this way it can be shown that the achievable delay in a linear, two-port device is subject to a limitation of the product of the delay and the bandwidth (Lenz et al., 2001).
One of the key issues when dealing with slow light is the inevitable effect of dispersion, the result of which is to broaden a pulse upon propagation. Moreover, the dispersion tends to increase when the group velocity, the speed at which the pulse propagates, decreases. To see this, we note that if we write the group velocity vg ≡ c/ng, where ng is the group index, then we find that ng = n+ωdn/dω. Since for the materials we are interested in, the refractive index does not vary strongly in magnitude, and slow light is obtained when the derivative dn/dω is large and positive. However, as the variations in the magnitude of n itself are limited, the large derivative can only be maintained over a narrow bandwidth ∝ (dn/dω)−1. Therefore, a large delay implies a narrow bandwidth, and hence a limited pulse width. Here we discuss how to avoid this limit by using nonlinear effects in the form of gap solitons. Though this argument is quite simple, it can be made rigorous using the Kramers-Kronig relations. In this way it can be shown that the achievable delay in a linear, two-port device is subject to a limitation of the product of the delay and the bandwidth (Lenz et al., 2001).
The group velocity at which light pulses propagate through a dispersive material system is very different from the vacuum speed of light c, One refers to light as being "slow" for v g << c (Boyd & Gauthier, 2009) or "fast" for v g > c or v g <0 (Stenner et al, 2003 ).For v g <0, the pulse envelope appears to travel backward in the material (Gehring et al, 2006), and hence it is sometimes referred to as "backward light."The subject of slow light has caused keen interest in the past decade or more, and it is possible to control the group velocity of light pulses in the dispersive materials.Interest in slow and fast light dates back to the early days of the 20th century.Sommerfeld and Brillouin (Sommerfeld & Brillouin, 1960) were intrigued by the fact that theory predicts that v g can exceed c, which leads to apparent inconsistencies with Einstein's special theory of relativity.Experimental investigations of extreme propagation velocities were performed soon after the invention of the laser (Faxvog and et al, 1970).In 1999, Harris's group research work greatly stimulated researchers' interests, which showed that light could be slowed down to 17m/s.The result was obtained in ultra cold atom clouds with the use of electromagnetically induced transparency (EIT), which induces transparency in a material while allowing it to retain strong linear and nonlinear optical properties (Hau et al, 1999).Slow light can also be obtained through the use of the optical response of hot atomic vapors (Philips et al, 2001).These early research works require hard conditions and the slow light cannot operate in room temperature.Recently, researchers found ways to realize slow light operating in room temperature and solid-state materials, which are more suited for many practical applications, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.In this chapter, we describe some of the physical mechanisms that can be used to induce slow and fast light effects in room-temperature solids (Bigelow et al, 2003) and some of the exotic propagation effects that can thereby be observed.We also survey some applications of slow and fast light within the fields of quantum electronics and photonics. Fundamentals of slow and fast lightSlow and fast light refer to the group velocity of a light wave.The group velocity is the velocity most closely related to the velocity at which the peak of a light pulse moves through an optical dispersive material (Milonni, 2005), and is given by the standard result www.intechopen.comRecent Progress in Optical Fiber Research 82where n is the refractive (phase) index and ω is the angular frequency of the carrier wave of the light field.One refers to light as being slow light for v g << c, fast light for for v g > c, and backwards light for v g <0 or v g is negative.Extreme values of the group velocity invariably rely on the dominance of the second contribution to the group index of Equation ( 1).This contribution of course results from the frequency dependence of the refractive index, and for this reason extreme values of the group velocity are usually associated with the resonant or near-resonant response of material systems.According to this theory, slow light is expected in the wings of an absorption line and fast light is expected near line center, and the spatial dispersion, that is, the non-locality in space of the medium response, is another mechanism that can lead to slow light, as has been predicted (Kocharovskaya et al,2001) and observed (Strekalov et al, 2001).We catalogue the main methods to realize slow light in room temperature solid, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.We will describe CPO and SBS slow light in more details.
As evidenced by this book, there has been a flurry of activity over the last decade on tailoring the dispersive properties of optical materials [1]. What has captured the attention of the research community were some of the early results on creating spectral regions of large normal dispersion [2-4]. Large normal dispersion results in extremely small group velocities, where the group velocity is the approximate speed at which a pulse of light propagates through a material. We denote the group velocity by υg = c/ng, where c is the speed of light in vacuum and ng is known as the group index. In the early experiments, described in greater detail in Chapter 1, a dilute gas of atoms is illuminated by a control or coupling beamwhose frequency is tuned precisely to an optical transition of an atom. This control field modifies the absorption and dispersion properties of another atomic transition that shares a common energy level. A narrow transparencywindow is created on this second transition-a process known as electromagnetically induced transparency (EIT)—and within this window, υg takes on extremely small values. Many experiments have now observed υg ∼ 1 m/s or less, implying ng > 108. This result is remarkable, considering the fact that the refractive index n of a material rarely exceeds 3 in the visible part of the spectrum.What are the implications of such large group indices? What applications are enabled by this basic science discovery?
Frontiers in Guided Wave Optics and Optoelectronics 84 absorption is much too high to render the group effect useful.An exciting breakthrough happened in the early nineties when it was shown that group velocities of few tens of meters per second were possible with nonlinear resonance interactions (Hau et al., 1999).Two important features of nonlinear resonances make this possible: substantially reduced absorption, or even amplification, of radiation at a resonance, and sharpness of such resonances; the sharper a resonance, the higher dn/dω and so the stronger the enhancement of group index, and hence the greater the pulse is delayed.Widely ranging applications for slow light have been proposed, of which those for telecommunication systems and devices (optical delay lines, optical buffers, optical equalizers and signal processors) are currently of most interest (Gauthier, 2005).The essential demand of such devices is compatibility with existing telecommunication systems, that is they must be of wide enough bandwidth (≥10 GHz) and able to be integrated seamlessly into such systems.Of the various nonlinear resonance mechanisms and media, which allow sufficiently long induced delays, stimulated Brillouin and Raman scattering (SBS and SRS) in optical fiber are deemed to be among the best candidates.Currently SBS is the most actively investigated and many experimental and theoretical papers on pulse delaying via SBS in optical fiber have been published in the last few years, see the review paper (Thevenaz, 2008) and references therein.In this process the pulse to be delayed is a frequency down-shifted (Stokes) pulse.This is transmitted through an optical fiber through which continuous wave (CW) pump radiation is sent in the opposite direction to prime the delay process.It is supposed that the Stokes pulse is amplified by parametric coupling with the pump wave and a material (acoustic) wave in the medium (Kroll, 1965), and the amplification is characterised by a resonant-type gain profile.The dispersion of refractive index associated with this profile (which is similar to that in Fig. 1) can then be used to increase the group index for optical pulses at the Stokes frequency (Zeldovich, 1972).Along with obvious device compatibility, there are several other advantages of the SL via SBS approach for optical communications systems: slow-light resonance can be created at any wavelength by changing the pump wavelength; use of optical fibre allows for long interaction lengths and thus low powers for the pump radiation, the process runs at room temperature, it uses off the shelf telecom equipment, and SBS works in the entire transparency range of fibers and in all types of fiber.Currently a main obstacle to applications of this approach is the narrow SBS gain spectral bandwidth, (Thevenaz, 2008), which is typically ≈ 120-200 MHz in silica fiber in the spectral range of telecom optical radiation (~1.3-1.6 μm) (Agrawal, 2006).This chapter reviews our ongoing work on the physical mechanisms that give rise to pulse delay in SBS.In section 2 the theoretical background of the SBS phenomenon is given and the main working equations describing this nonlinear interaction are presented.In section 3 ways by which the SBS spectral bandwidth may be increased are addressed.Waveguide induced spectral broadening of SBS in optical fibre is considered as a means of increasing the bandwidth to the multi-GHz range.An alternative way widely discussed in the literature, (Thevenaz, 2008), is based on spectral broadening of the pump radiation.However it is shown through analytic analysis of the SBS equations converted to the frequency domain that pump radiation broadening by any reasonable amount has only a negligible effect on increasing the SBS bandwidth.Importantly in this section we show that, irrespective of the nature of the broadening considered, the SBS gain bandwidth remains www.intechopen.
Paradoxically, slow light promises to increase the speed of telecommunications in novel photonic structures, such as coupled resonators [1] and photonic crystals [2,3]. Apart from signal delays, the key consequence of slowing light down is the enhancement of light-matter interactions. Linear effects such as refractive index modulation scale linearly with slowdown in photonic crystals [3], and nonlinear effects are expected to scale with its square [4]. By directly observing the spatial compression of an optical pulse, by factor 25, we confirm the mechanism underlying this square scaling law. The key advantage of photonic structures over other slow light concepts is the potentially large bandwidth, which is crucial for telecommunications [5]. Nevertheless, the slow light previously observed in photonic crystals [2,3,6,7] has been very dispersive and featured narrow bandwidth. We demonstrate slow light with a bandwidth of 2.5 THz and a delay-bandwidth product of 30, which is an order of magnitude larger than any reported so far.
The manipulation of the group velocity of optical signals (slow and fast light) has many possible applications in telecommunications, sensing, nonlinear optics, and so on. The exploitation of the effect of stimulated Brillouin scattering (SBS) is of special interest for the alteration of the group velocity in optical fibers, since it just requires standard telecom equipment and low-to-moderate optical power. However, each delay in one single, low-gain SBS-based slow-light system is accompanied by a pulse broadening. This is a result of the inherent Kramers–Kronig relations among the gain, the phase change, and the accompanied group velocity. For an ideal flat gain, the phase change is nonideal, and for an ideal phase change the gain curve leads to a broadening. Furthermore, if the gain bandwidth is adapted to the signal by broadening, the delay will be reduced. Thus the signal broadening can be reduced by several methods for one single low-gain slow-light system, but it cannot be zero. Here, we will show how a zero-broadening SBS-based slow light can be achieved with several methods. The basic idea is a reshaping of the original pulse in a second stage by saturation of the SBS system, or by the superposition of two gains. As will be shown, all of these systems show an almost ideal overall gain and phase function over the bandwidth of the pulses. Thus, SBS-based slow light with a delay bandwidth product of 1 bit and zero distortion is possible.
The slow-light effect, which implies reduction of the group velocity of light by many orders of magnitude, is considered to be one of the most exciting discoveries in quantum optics of the last decade. The physics underlying the effect is related to an extremely steep dispersion of the medium in a very narrow region of its transparency, while all the manifestations of the effect are usually reduced just to a small pulse delay. Perhaps this is the reason why, after the discovery of the slow-light effect, some of the simplest nonlinear phenomena associated with a retarded optical response have been implicitly revised and assigned to reduction of the light group velocity. In this lecture, a few examples of common inconsistencies in the area of the slow-light physics will be presented.