Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Physica Scripta

All-optical memory based on slow light and Kerr effect in photonic crystal platform with independent write/read/hold control

Sina Mirzaiee, Mina Noori, Hamed Baghban, Hadi Veladi

Published Apr 22, 2022• 12 citations
Publisher

Abstract

Abstract A general scheme has been proposed for the design of photonic-crystal-based all-optical memory by implementing the Kerr effect and slow light phenomenon and a memory cell with independent control on the read, write and hold processes is presented. A photonic crystal slab platform comprised of air holes in a square array with a hole radius of R = 192.5 nm and slab thickness of 275 nm is considered to realize the optical memory operating at the signal and pump wavelengths of λ = 1550 nm and λ = 1604 nm, respectively. The radii of the holes and the thickness of the proposed slab are engineered to provide proper functionality in the write/read waveguides and memory cell. For the slab thickness of 275 nm, the radii of the defect holes at the center of the read and write channels, and memory cell are determined to be 66 nm, 60.5 nm, and 55 nm, respectively. The pump pulse with a peak power of 2.65 W and a minimum time duration of ∼2.64 ps is required for the reading process. Also, the peak power and minimum time duration of 4.7 W and 1.35 ps, respectively are required to accomplish the writing process. The study has been carried out by 3D PWE and 3D FDTD methods.

DOI
10.1088/1402-4896/ac698e

Related papers

Fast bistable all-optical switch and memory on a silicon photonic crystal on-chip

Takasumi Tanabe, Masaya Notomi, Satoshi Mitsugi +2 more

We demonstrate extremely low-power all-optical bistability by utilizing silicon photonic crystal nanocavities, based on the plasma effect of carriers generated by two-photon absorption. Owing to the high quality factor and the small volume of the nanocavities, the photon density inside the cavity becomes extremely high, which leads to a large reduction in operation power. Optical bistable operation in a single nanocavity permits optical read-write memory operation, which opens the possibility of an integrated optical logic circuit on a single chip, based on photonic crystals. The demonstrated bistable threshold power is 0.4 mW with a set pulse energy of 74 fJ, at a switching speed of <100 ps.

Optics Letters•Oct 1, 2005•330 citations

Large delay-bandwidth product and tuning of slow light pulse in photonic crystal coupled waveguide

Toshihiko Baba, Takashi Kawaaski, Hirokazu Sasaki +2 more

This paper reports two advances in a slow light device consisting of chirped photonic crystal slab coupled waveguide on SOI substrate. One is concerning the delay-bandwidth product, indicating the buffering capacity of the device. We experimentally evaluated a record high value of 57 (a 40 ps delay and a 1.4 THz bandwidth). We also observed ~1 ps wide optical pulse transmission in the cross-correlation measurement. Regarding the pulse as a signal and considering the broadening of the pulse width due to the imperfect dispersion compensation in the device, storage of more than 12 signal bits was confirmed. The other is a wide-range tuning of the pulse delay. We propose a technique for externally controlling the chirping to permit variable delay. We demonstrate tuning of the pulse delay up to 23 ps, corresponding to a ~7 mm extension of the free space length.

Optics Express•Jun 6, 2008•126 citations

Controlling and switching slow light in photonic crystal waveguides

D. M. Beggs, Tobias Kampfrath, Isabella H. Rey +2 more

Using slow-light photonic crystal waveguides in ultrafast pump-probe experiments, we demonstrate the adiabatic frequency conversion and ultrafast switching of telecoms light pulses on a silicon chip. By storing a 1.3 ps pulse in the slow-light modes of a photonic crystal waveguide, we are able to blue-shift it by 0.3 THz with high (80%) efficiency. We show that the shift occurs when the pulse adiabatically follows the modes of the waveguide in which it travels upon these modes being perturbed by the absorption of a pump pulse. We also show rerouting of optical pulses in a bandwidth limited time of just 3ps. The switch is based on coupled W1 photonic crystal waveguides, and the interaction between the waveguide modes is optimised to give an ultra-short (~3λ) switching length of just 5μm.

International Conference on Transparent Optical Networks•Jun 1, 2011•4 citations

Single-photon storage in laser written waveguides fabricated in rare-earth-doped solids (Conference Presentation)

Giacomo Corrielli, Alessandro Seri, Dario Lago-Rivera +4 more

Efficient and long-lived multimode quantum memories are crucial devices in the development of quantum technolgies. The reversible mapping of quantum states of light in rare earth doped crystals represents one of the most promising routes towards the realization of this goal. Such systems are also compatible with the miniaturization of quantum memories in integrated optics platforms, which offer unique features in terms of experimental scalability and enhanced light-matter interaction. Here, we fabricate single mode channel waveguides for 606 nm light in a praseodymium-doped yttrium orthosilicate crystal (Pr3+:Y2SiO5), that, thanks to its excellent coherence properties, is a widely studied material for light storage experiments. Waveguides are inscribed by femtosecond laser writing, adopting the so-called Type I configuration, where the core is directly obtained at the irradiated area. Remarkably, fabricating this kind of waveguides in crystals is a difficult task, as it requires to operate in a very narrow processing parameters window, if existing. We then use these waveguides for performing the storage and retrieval of single photons, implementing the atomic frequency comb protocol. We achieve a storage time of 5,5 µs, which is almost 2 orders of magnitude longer than previous realizations of quantum light storage in a waveguide. In addition, we investigate the potential information multiplexing capabilities of our system by performing the quantum storage of single photons delocalized over 14 different spectral modes. Our results show that laser written waveguides in rare earth-doped solid state systems are very promising for the development of efficient and long-lived multimode quantum memories.

Advances in Photonics of Quantum Computing, Memory, and Communication•Mar 4, 2019•0 citations

Understanding of controllable optical memory using 1D InP based photonic structures at three communication windows

M. Rajesh Khanna, A. Karthikeyan, Peramandai Govindasamy Kuppusamy +1 more

Abstract The present research realises a controllable optical memory using one dimensional indium phosphate (InP) photonic structures at three optical communication windows (850 nm, 1310 nm and 1550 nm). The photonic structures comprise 21 layers of InP and air material. The memory applications are realised at both single and dual signals of the communication windows. The physics of the research deals with the materials property including the variation of the refractive indices with respect to the input signal. Similarly, mathematics of the works relies on the analysis of reflectance, transmittance and absorbance phenomena. Further, the light from visible spectrum acts as triggering signal to realise optical memory applications. Finally, it is revealed that InP based photonic structures are suitable for controllable memory applications pertaining to the single wavelength (850 nm, 1310 nm, 1550 nm) or dual wavelengths (850 nm and 1310 nm, 1310 nm and 1550 nm, 1550 nm and 850 nm).

Optical and Quantum Electronics•May 12, 2022•1 citation

Erbium-Based Photonic Flip-Flop Memories: Model and Experimental Validation

Luca Potì

Operating principle for a flip-flop memory cell based on erbium-doped devices is presented. A complete model for memory dynamics is introduced taking into account, at the same time, for memory writing, reading, and erasing. Simple equations are found relating writing, spontaneous and stimulated erasing times to device physical parameters, signals wavelength and power. In principle, for example, increasing writing and erasing energies at the appropriate wavelength it is possible to dramatically reduce transition times. Extinction ratio (ER) is also determined as a function of host medium, and signals properties. An optimization technique is proposed for erasing signal design in order to guarantee maximum ER. Numerical example are provided for Er and Er-Yb doped fibers whose doping ion density is rho = 1.1413middot1024ions/m3, and 2.0 middot1025ions/m3, respectively. Finally, an experimental demonstration giving an Er higher than 5 and 16 dB for the two fibers, respectively, is provided and discussed.

IEEE Journal of Quantum Electronics•Mar 12, 2008•6 citations
Abstract A general scheme has been proposed for the design of photonic-crystal-based all-optical memory by implementing the Kerr effect and slow light phenomenon and a memory cell with independent control on the read, write and hold processes is presented. A photonic crystal slab platform comprised of air holes in a square array with a hole radius of R = 192.5 nm and slab thickness of 275 nm is considered to realize the optical memory operating at the signal and pump wavelengths of λ = 1550 nm and λ = 1604 nm, respectively. The radii of the holes and the thickness of the proposed slab are engineered to provide proper functionality in the write/read waveguides and memory cell. For the slab thickness of 275 nm, the radii of the defect holes at the center of the read and write channels, and memory cell are determined to be 66 nm, 60.5 nm, and 55 nm, respectively. The pump pulse with a peak power of 2.65 W and a minimum time duration of ∼2.64 ps is required for the reading process. Also, the peak power and minimum time duration of 4.7 W and 1.35 ps, respectively are required to accomplish the writing process. The study has been carried out by 3D PWE and 3D FDTD methods.
We demonstrate extremely low-power all-optical bistability by utilizing silicon photonic crystal nanocavities, based on the plasma effect of carriers generated by two-photon absorption. Owing to the high quality factor and the small volume of the nanocavities, the photon density inside the cavity becomes extremely high, which leads to a large reduction in operation power. Optical bistable operation in a single nanocavity permits optical read-write memory operation, which opens the possibility of an integrated optical logic circuit on a single chip, based on photonic crystals. The demonstrated bistable threshold power is 0.4 mW with a set pulse energy of 74 fJ, at a switching speed of <100 ps.
This paper reports two advances in a slow light device consisting of chirped photonic crystal slab coupled waveguide on SOI substrate. One is concerning the delay-bandwidth product, indicating the buffering capacity of the device. We experimentally evaluated a record high value of 57 (a 40 ps delay and a 1.4 THz bandwidth). We also observed ~1 ps wide optical pulse transmission in the cross-correlation measurement. Regarding the pulse as a signal and considering the broadening of the pulse width due to the imperfect dispersion compensation in the device, storage of more than 12 signal bits was confirmed. The other is a wide-range tuning of the pulse delay. We propose a technique for externally controlling the chirping to permit variable delay. We demonstrate tuning of the pulse delay up to 23 ps, corresponding to a ~7 mm extension of the free space length.
Using slow-light photonic crystal waveguides in ultrafast pump-probe experiments, we demonstrate the adiabatic frequency conversion and ultrafast switching of telecoms light pulses on a silicon chip. By storing a 1.3 ps pulse in the slow-light modes of a photonic crystal waveguide, we are able to blue-shift it by 0.3 THz with high (80%) efficiency. We show that the shift occurs when the pulse adiabatically follows the modes of the waveguide in which it travels upon these modes being perturbed by the absorption of a pump pulse. We also show rerouting of optical pulses in a bandwidth limited time of just 3ps. The switch is based on coupled W1 photonic crystal waveguides, and the interaction between the waveguide modes is optimised to give an ultra-short (~3λ) switching length of just 5μm.
Efficient and long-lived multimode quantum memories are crucial devices in the development of quantum technolgies. The reversible mapping of quantum states of light in rare earth doped crystals represents one of the most promising routes towards the realization of this goal. Such systems are also compatible with the miniaturization of quantum memories in integrated optics platforms, which offer unique features in terms of experimental scalability and enhanced light-matter interaction. Here, we fabricate single mode channel waveguides for 606 nm light in a praseodymium-doped yttrium orthosilicate crystal (Pr3+:Y2SiO5), that, thanks to its excellent coherence properties, is a widely studied material for light storage experiments. Waveguides are inscribed by femtosecond laser writing, adopting the so-called Type I configuration, where the core is directly obtained at the irradiated area. Remarkably, fabricating this kind of waveguides in crystals is a difficult task, as it requires to operate in a very narrow processing parameters window, if existing. We then use these waveguides for performing the storage and retrieval of single photons, implementing the atomic frequency comb protocol. We achieve a storage time of 5,5 µs, which is almost 2 orders of magnitude longer than previous realizations of quantum light storage in a waveguide. In addition, we investigate the potential information multiplexing capabilities of our system by performing the quantum storage of single photons delocalized over 14 different spectral modes. Our results show that laser written waveguides in rare earth-doped solid state systems are very promising for the development of efficient and long-lived multimode quantum memories.
Abstract The present research realises a controllable optical memory using one dimensional indium phosphate (InP) photonic structures at three optical communication windows (850 nm, 1310 nm and 1550 nm). The photonic structures comprise 21 layers of InP and air material. The memory applications are realised at both single and dual signals of the communication windows. The physics of the research deals with the materials property including the variation of the refractive indices with respect to the input signal. Similarly, mathematics of the works relies on the analysis of reflectance, transmittance and absorbance phenomena. Further, the light from visible spectrum acts as triggering signal to realise optical memory applications. Finally, it is revealed that InP based photonic structures are suitable for controllable memory applications pertaining to the single wavelength (850 nm, 1310 nm, 1550 nm) or dual wavelengths (850 nm and 1310 nm, 1310 nm and 1550 nm, 1550 nm and 850 nm).
Operating principle for a flip-flop memory cell based on erbium-doped devices is presented. A complete model for memory dynamics is introduced taking into account, at the same time, for memory writing, reading, and erasing. Simple equations are found relating writing, spontaneous and stimulated erasing times to device physical parameters, signals wavelength and power. In principle, for example, increasing writing and erasing energies at the appropriate wavelength it is possible to dramatically reduce transition times. Extinction ratio (ER) is also determined as a function of host medium, and signals properties. An optimization technique is proposed for erasing signal design in order to guarantee maximum ER. Numerical example are provided for Er and Er-Yb doped fibers whose doping ion density is rho = 1.1413middot1024ions/m3, and 2.0 middot1025ions/m3, respectively. Finally, an experimental demonstration giving an Er higher than 5 and 16 dB for the two fibers, respectively, is provided and discussed.