Nonlinear Transmission Line Model of a Josephson Traveling-Wave Parametric Amplifier including Noise and Dissipation

Abstract

Josephson traveling-wave parametric amplifiers (JTWPAs) achieve high parametric gain through four-wave-mixing with near quantum-limited noise performance and extremely low energy consumption. This makes them suitable for the detection of ultra-low-power microwave signals in the lowest temperature stage of a dilution refrigerator. Distributed circuit representations of JTWPAs have been studied in the framework of classical theory. A nonlinear wave equation describing the flux along a nonlinear transmission line was derived in [1]. Dispersion engineering was introduced in [2] to increase the amplifier’s gain and bandwidth by means of resonant phase-matching (RPM). In the classical treatment [1], dielectric loss is considered for the formulation of the wave equation, however, a closed-form solution was only given when dissipation was neglected. Our work focuses on the effects of noise and dissipation in the nonlinear transmission line. Our model differs from [1],[2], where we derive the telegrapher’s equations taking into account the loss and noise contributions to construct the current-flux-relation. In the super-conducting state, the dissipation due to the imperfect electric insulation in the substrate needs to be taken into account. It is represented by a parallel conductance and an additional noise source describing temporal fluctuations [3]. The flux along the transmission line is expanded into three discrete modes, representing pump, signal, and idler contributions. The equations of motion of the signal and idler modes result in\begin{equation*}{\partial _z}{\tilde A_{\text{s}}} = - \left( {{\Gamma _{\text{s}}}/2 + {\text{i}}\Delta {k_{\text{T}}}/2} \right){\tilde A_{\text{s}}} + {\text{i}}{\kappa _{\text{s}}}\tilde A_{\text{i}}^{\ast} + {\tilde f_{\text{s}}}\left( {i_{\text{s}}^{{\text{noise}}}} \right),\quad {\partial _z}{\tilde A_{\text{i}}} = - \left( {{\Gamma _{\text{i}}}/2 + {\text{i}}\Delta {k_{\text{T}}}/2} \right){\tilde A_{\text{i}}} + {\text{i}}{\kappa _{\text{i}}}\tilde A_{\text{s}}^{\ast} + {\tilde f_{\text{i}}}\left( {i_{\text{i}}^{{\text{noise}}}} \right),\tag{1}\end{equation*}where Ãnare the mode amplitudes in a co-rotating frame, ∆kTis the total phase mismatch, κndescribe the coupling due to four-wave-mixing, Γnare the damping factors and ${\tilde f_n}$ represent thermal fluctuations on the transmission line, with n ∈ {s,i}. Pump-depletion was neglected when deriving the equations above. We define the signal power gain Gsas the ratio of output to input power. Assuming no initial idler contribution at the input of the device, we obtain\begin{equation*}{G_{\text{S}}} = {\left| {\cosh (gz) + \frac{{ - {\Gamma _{\text{s}}} + {\Gamma _{\text{i}}} - 2{\text{i}}\Delta {k_{\text{T}}}}}{{4g}}\sinh (gz)} \right|^2}{{\text{e}}^{ - \frac{1}{2}\left( {{\Gamma _{\text{s}}} + {\Gamma _{\text{i}}}} \right)z}},\tag{2}\end{equation*}where g is the gain factor, which depends on the coupling strength, the pump amplitude and the total phase mismatch. The gain spectrum of the JTWPA setup from [4] was calculated according to our model with good agreement to the results in the literature. The gain spectrum of the JTWPA is plotted in Fig. 1 (a) without RPM and in Fig. 1 (b) with RPM, both for the case with and without dissipation.