Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Letters

Force sensing in a dual-mode optomechanical system with linear–quadratic coupling and modulated photon hopping

Shi‐Lei Chao, Zhen Yang, Chengsong Zhao, Rui Peng, Ling Zhou

Published Jun 2, 2021• 19 citations
Publisher

Abstract

A weak force sensor scheme is presented in an optomechanical system, in which the two cavity modes couple to a mechanical mode with linear and quadratic coupling. Due to introducing time-dependent hopping, the linear and quadratic coupling terms coexist under the rotating-wave approximation in the interaction picture. Compared with the quantum non-demolition measurement (ignoring the quadratic optomechanical coupling), the current scheme can decrease the additional noise to a lower level. Our proposal provides a promising platform for improving the detection of a weak force.

DOI
10.1364/ol.425484

Related papers

Squeezing-enhanced quantum sensing with quadratic optomechanics

Sheng-Dian Zhang, Jie Wang, Qian Zhang +6 more

Cavity optomechanical (COM) sensors, enhanced by quantum squeezing or entanglement, have become powerful tools for measuring ultra-weak forces with high precision and sensitivity. However, these sensors usually rely on linear COM couplings, a fundamental limitation when measurements of the mechanical energy are desired. Very recently, a giant enhancement of the signal-to-noise ratio was predicted in a quadratic COM system. Here we show that the performance of such a system can be further improved surpassing the standard quantum limit by using quantum squeezed light. Our approach is compatible with available engineering techniques of advanced COM sensors and provides new opportunities for using COM sensors in tests of fundamental laws of physics and quantum metrology applications.

arXiv:2202.08690•Optica Quantum•Jun 7, 2024•30 citations

Enhancing force sensing in a squeezed optomechanical system with quantum non-demolition measurement

Shi‐Lei Chao, Zihao Li, Xin‐You Lü

Abstract A theoretical scheme is proposed to enhance the sensitivity of force sensors with quantum non-demolition measurement (QND) in an optomechanical setup assisted by four-tone optical driving and an optical parametric amplifier (OPA). With the help of special drive, the system can be simplified as the typical type of QND for force sensing, so that the backaction noise can be evaded to surpass the standard quantum limit. Besides, the added noise can be suppressed owing to the modified optical susceptibility resulting from the OPA. By introducing two oscillators coupling with two charged bodies respectively, the signal can be enhanced with the nonlinearity caused by Coulomb interaction, while the noise presents an exponential decrease. Moreover, considering the homodyne detection effect, the range of system parameters and frequency bands will be broadened. The present investigation may provide a route toward simultaneously evading backaction noise, reducing the mechanical thermal noise, and enhancing the external signal, which can be an alternative design for sensitive devices.

Communications in Theoretical Physics•Nov 13, 2023•3 citations

Backaction Evading and Amplification of Weak Force Signal in an Optomechanical System

Shi‐Lei Chao, Da‐Wei Wang, Zhen Yang +3 more

Abstract A scheme of backaction evading and amplification of weak force signal is presented in an optomechanical system. By introducing the frequency modulation of the cavity field, the system can achieve the quantum nondemolition measurement interaction so that the backaction evading can be reached. With the help of the mechanical squeezing, the weak force signal can be amplified, which equals to amplifying the mechanical response function, reducing additional noise as well as thermal noise of mechanical oscillator. The current scheme opens up an alternative method for simultaneously surpassing the standard quantum limit and enhancing the mechanical response, and also reducing the mechanical thermal noise.

Annalen der Physik•Jan 11, 2022•5 citations

Enhanced weak force sensing based on atom-based coherent quantum noise cancellation in a hybrid cavity optomechanical system

S. K. Singh, Mojtaba Mazaheri, Jia‐Xin Peng +3 more

The weak force sensing based on a coherent quantum noise cancellation (CQNC) scheme is presented in a hybrid cavity optomechanical system containing a trapped ensemble of ultracold atoms and an optical parametric amplifier (OPA). In the proposed system, the back-action noise can be completely eliminated at all frequencies and through the proper choice of the OPA parameters, and the noise spectral density can also be reduced at lower frequencies. This leads to a significant enhancement in the sensitivity of the cavity optomechanical weak force sensor, and the noise spectral density also surpasses the standard quantum limit (SQL) even for the small input power at the lower detection frequency. Furthermore, the experimental feasibility of this scheme is also briefly discussed. This study can be used for the realization of a force sensor based on hybrid cavity optomechanical systems and for the coherent quantum control in macroscopic systems.

arXiv:2201.10805•Frontiers in Physics•Apr 7, 2023•46 citations

Squeezing enhanced homodyne weak force sensing in cavity optomechanics

Madan Mohan Mahana, Sanket Das, Tarak Nath Dey

Cavity optomechanical systems have emerged as a promising platform for quantum sensing. Quantum mechanics imposes a standard quantum limit (SQL) on the force-sensitivity for the standard homodyne phase quadrature measurement of the cavity's output field. In this paper, we investigate ways to enhance weak force sensitivity beyond SQL by employing a variational homodyne quadrature readout and quantum squeezing. Our study reveals a remarkable improvement in the force sensitivity of a cavity optomechanical sensor at a suitable homodyne angle, compared with standard phase quadrature detection of the cavity output field within a specific frequency band. We further demonstrate improved force sensitivity via intra-cavity squeezing (ICS) or injected external squeezing (IES) of the cavity mode. Both variational homodyne readout and quantum squeezing induce quantum correlations between the amplitude and phase quadratures of the cavity's output field, thereby improving force sensitivity. Our results suggest that IES is preferable to ICS for sub-SQL force sensing with system stability and lower probe power requirements. The squeezing-enhanced variational homodyne detection scheme can enable high-precision quantum sensing across various hybrid quantum platforms.

quant-pharXiv:2606.28007•Jun 29, 2026•0 citations

Quantum measurement with cavity optomechanical systems

Chen Xue, Liu Xiao-Wei, Keye Zhang +2 more

Cavity optomechanics originated from the research of interferometric detection of gravitational waves, and later became a fast-growing area of techniques and approaches ranging from the fields of atomic, molecular, and optical physics to nano-science and condensed matter physics as well. Recently, it focused on the exploration of operating mechanical oscillators deep in the quantum regime, with an interest ranging from quantum-classical interface tests to high-precision quantum metrology. In this paper, recent theoretical work of our group in the field of quantum measurement with cavity optomechanical systems is reviewed. We explore the quantum measurement theory and its applications with several unconventional cavity optomechanical schemes working in the quantum regime. This review covers the basics of quantum noises in the cavity optomechanical setups and the resulting standard quantum limit of precision displacement and force measurement. Three novel quantum measurement proposals based on the hybrid optomechanical system are introduced. First, we describe a quantum back-action insulated weak force sensor. It is realized by forming a quantum-mechanics-free subsystem with two optomechanical oscillators of reversed effective mass. Then we introduce a role-reversed atomic optomechanical system which enables the preparation and the quantum tomography of a variety of non-classical states of atoms. In this system, the cavity field acts as a mechanical oscillator driven by the radiation pressure force from an ultracold atomic field. In the end, we recommend a multimode optomechanical transducer that can detect intensities significantly below the single-photon level via adiabatic transfer of the microwave signal to the optical frequency domain. These proposals demonstrate the possible applications of optomechanical devices in understanding of quantum-classical crossover and in achieving quantum measurement limit.

Acta Physica Sinica•Jan 1, 2015•16 citations
A weak force sensor scheme is presented in an optomechanical system, in which the two cavity modes couple to a mechanical mode with linear and quadratic coupling. Due to introducing time-dependent hopping, the linear and quadratic coupling terms coexist under the rotating-wave approximation in the interaction picture. Compared with the quantum non-demolition measurement (ignoring the quadratic optomechanical coupling), the current scheme can decrease the additional noise to a lower level. Our proposal provides a promising platform for improving the detection of a weak force.
Cavity optomechanical (COM) sensors, enhanced by quantum squeezing or entanglement, have become powerful tools for measuring ultra-weak forces with high precision and sensitivity. However, these sensors usually rely on linear COM couplings, a fundamental limitation when measurements of the mechanical energy are desired. Very recently, a giant enhancement of the signal-to-noise ratio was predicted in a quadratic COM system. Here we show that the performance of such a system can be further improved surpassing the standard quantum limit by using quantum squeezed light. Our approach is compatible with available engineering techniques of advanced COM sensors and provides new opportunities for using COM sensors in tests of fundamental laws of physics and quantum metrology applications.
Abstract A theoretical scheme is proposed to enhance the sensitivity of force sensors with quantum non-demolition measurement (QND) in an optomechanical setup assisted by four-tone optical driving and an optical parametric amplifier (OPA). With the help of special drive, the system can be simplified as the typical type of QND for force sensing, so that the backaction noise can be evaded to surpass the standard quantum limit. Besides, the added noise can be suppressed owing to the modified optical susceptibility resulting from the OPA. By introducing two oscillators coupling with two charged bodies respectively, the signal can be enhanced with the nonlinearity caused by Coulomb interaction, while the noise presents an exponential decrease. Moreover, considering the homodyne detection effect, the range of system parameters and frequency bands will be broadened. The present investigation may provide a route toward simultaneously evading backaction noise, reducing the mechanical thermal noise, and enhancing the external signal, which can be an alternative design for sensitive devices.
Abstract A scheme of backaction evading and amplification of weak force signal is presented in an optomechanical system. By introducing the frequency modulation of the cavity field, the system can achieve the quantum nondemolition measurement interaction so that the backaction evading can be reached. With the help of the mechanical squeezing, the weak force signal can be amplified, which equals to amplifying the mechanical response function, reducing additional noise as well as thermal noise of mechanical oscillator. The current scheme opens up an alternative method for simultaneously surpassing the standard quantum limit and enhancing the mechanical response, and also reducing the mechanical thermal noise.
The weak force sensing based on a coherent quantum noise cancellation (CQNC) scheme is presented in a hybrid cavity optomechanical system containing a trapped ensemble of ultracold atoms and an optical parametric amplifier (OPA). In the proposed system, the back-action noise can be completely eliminated at all frequencies and through the proper choice of the OPA parameters, and the noise spectral density can also be reduced at lower frequencies. This leads to a significant enhancement in the sensitivity of the cavity optomechanical weak force sensor, and the noise spectral density also surpasses the standard quantum limit (SQL) even for the small input power at the lower detection frequency. Furthermore, the experimental feasibility of this scheme is also briefly discussed. This study can be used for the realization of a force sensor based on hybrid cavity optomechanical systems and for the coherent quantum control in macroscopic systems.
Cavity optomechanical systems have emerged as a promising platform for quantum sensing. Quantum mechanics imposes a standard quantum limit (SQL) on the force-sensitivity for the standard homodyne phase quadrature measurement of the cavity's output field. In this paper, we investigate ways to enhance weak force sensitivity beyond SQL by employing a variational homodyne quadrature readout and quantum squeezing. Our study reveals a remarkable improvement in the force sensitivity of a cavity optomechanical sensor at a suitable homodyne angle, compared with standard phase quadrature detection of the cavity output field within a specific frequency band. We further demonstrate improved force sensitivity via intra-cavity squeezing (ICS) or injected external squeezing (IES) of the cavity mode. Both variational homodyne readout and quantum squeezing induce quantum correlations between the amplitude and phase quadratures of the cavity's output field, thereby improving force sensitivity. Our results suggest that IES is preferable to ICS for sub-SQL force sensing with system stability and lower probe power requirements. The squeezing-enhanced variational homodyne detection scheme can enable high-precision quantum sensing across various hybrid quantum platforms.
Cavity optomechanics originated from the research of interferometric detection of gravitational waves, and later became a fast-growing area of techniques and approaches ranging from the fields of atomic, molecular, and optical physics to nano-science and condensed matter physics as well. Recently, it focused on the exploration of operating mechanical oscillators deep in the quantum regime, with an interest ranging from quantum-classical interface tests to high-precision quantum metrology. In this paper, recent theoretical work of our group in the field of quantum measurement with cavity optomechanical systems is reviewed. We explore the quantum measurement theory and its applications with several unconventional cavity optomechanical schemes working in the quantum regime. This review covers the basics of quantum noises in the cavity optomechanical setups and the resulting standard quantum limit of precision displacement and force measurement. Three novel quantum measurement proposals based on the hybrid optomechanical system are introduced. First, we describe a quantum back-action insulated weak force sensor. It is realized by forming a quantum-mechanics-free subsystem with two optomechanical oscillators of reversed effective mass. Then we introduce a role-reversed atomic optomechanical system which enables the preparation and the quantum tomography of a variety of non-classical states of atoms. In this system, the cavity field acts as a mechanical oscillator driven by the radiation pressure force from an ultracold atomic field. In the end, we recommend a multimode optomechanical transducer that can detect intensities significantly below the single-photon level via adiabatic transfer of the microwave signal to the optical frequency domain. These proposals demonstrate the possible applications of optomechanical devices in understanding of quantum-classical crossover and in achieving quantum measurement limit.