Cavity optomechanics originated from the research of interferometric detection of gravitational waves, and later became a fast-growing area of techniques and approaches ranging from the fields of atomic, molecular, and optical physics to nano-science and condensed matter physics as well. Recently, it focused on the exploration of operating mechanical oscillators deep in the quantum regime, with an interest ranging from quantum-classical interface tests to high-precision quantum metrology. In this paper, recent theoretical work of our group in the field of quantum measurement with cavity optomechanical systems is reviewed. We explore the quantum measurement theory and its applications with several unconventional cavity optomechanical schemes working in the quantum regime. This review covers the basics of quantum noises in the cavity optomechanical setups and the resulting standard quantum limit of precision displacement and force measurement. Three novel quantum measurement proposals based on the hybrid optomechanical system are introduced. First, we describe a quantum back-action insulated weak force sensor. It is realized by forming a quantum-mechanics-free subsystem with two optomechanical oscillators of reversed effective mass. Then we introduce a role-reversed atomic optomechanical system which enables the preparation and the quantum tomography of a variety of non-classical states of atoms. In this system, the cavity field acts as a mechanical oscillator driven by the radiation pressure force from an ultracold atomic field. In the end, we recommend a multimode optomechanical transducer that can detect intensities significantly below the single-photon level via adiabatic transfer of the microwave signal to the optical frequency domain. These proposals demonstrate the possible applications of optomechanical devices in understanding of quantum-classical crossover and in achieving quantum measurement limit.
Cavity optomechanics originated from the research of interferometric detection of gravitational waves, and later became a fast-growing area of techniques and approaches ranging from the fields of atomic, molecular, and optical physics to nano-science and condensed matter physics as well. Recently, it focused on the exploration of operating mechanical oscillators deep in the quantum regime, with an interest ranging from quantum-classical interface tests to high-precision quantum metrology. In this paper, recent theoretical work of our group in the field of quantum measurement with cavity optomechanical systems is reviewed. We explore the quantum measurement theory and its applications with several unconventional cavity optomechanical schemes working in the quantum regime. This review covers the basics of quantum noises in the cavity optomechanical setups and the resulting standard quantum limit of precision displacement and force measurement. Three novel quantum measurement proposals based on the hybrid optomechanical system are introduced. First, we describe a quantum back-action insulated weak force sensor. It is realized by forming a quantum-mechanics-free subsystem with two optomechanical oscillators of reversed effective mass. Then we introduce a role-reversed atomic optomechanical system which enables the preparation and the quantum tomography of a variety of non-classical states of atoms. In this system, the cavity field acts as a mechanical oscillator driven by the radiation pressure force from an ultracold atomic field. In the end, we recommend a multimode optomechanical transducer that can detect intensities significantly below the single-photon level via adiabatic transfer of the microwave signal to the optical frequency domain. These proposals demonstrate the possible applications of optomechanical devices in understanding of quantum-classical crossover and in achieving quantum measurement limit.
Cavity optomechanics represents a frontier research direction in quantum science and technology, centered on the control and exploration of interactions between electromagnetic fields and mechanical motion. Rooted in quantum mechanics, this field realizes efficient coupling and precise manipulation of optical fields and mechanical vibrations through the structural design and precise regulation of optical microcavities and mechanical oscillators, thereby revealing and harnessing novel quantum phenomena. In recent years, cavity optomechanics has evolved into an interdisciplinary frontier integrating quantum optics, condensed matter physics, and quantum precision measurement, exhibiting profound application in both fundamental physics research and quantum information science. With advancements in technologies such as nanomanufacturing and laser cooling, optomechanical interactions have been successfully demonstrated in various experimental systems. Among these platforms, cavity cold-atom systems stand out as one of the ideal platforms for implementing quantum optomechanics. Featuring exceptional environmental isolation, long quantum coherence times, and strong light-matter interaction, these systems provide a crucial testbed for exploring strong and even ultrastrong optomechanical coupling effects as well as rich nonlinear quantum phenomena. This paper reviews the recent progress in optomechanical control and manipulation based on cavity cold-atom systems. We first outline the fundamental principles of standard cavity optomechanical systems. Then, we describe the experimental realization of linear and nonlinear optomechanical couplings in cold-atom systems. After that, we focus on the representative applications of this platform in high-precision quantum sensing, quantum memory, and the preparation of macroscopic nonclassical states. Finally, we give an outlook and challenges in this field.
This thesis concentrates on generating and measuring non-classical states of mechanical oscillators by coupling them to atomic and molecular quantum systems. We start with a discussion of what novel physics can be explored by mechanical systems operating in the quantum regime. We then discuss one technique making it a possibility- cavity optomechanics, particularly optomechanical cooling. We investigate the limits of optomechanical cooling and review how the coupling of mechanical oscillators to external heat baths limits the minimum attainable phonon occupation number. As a possible alternative for circumventing clamping losses, we consider an all-optical approach where the mechanical element (in this case, a Bragg mirror) is suspended via optical forces, and discuss some limitations of this approach. We explore several schemes aimed at the generation of quantum states in mechanical oscillators. We consider specifically two examples: one in which the mechanical oscillator is coupled to polar molecules via dipole-dipole interaction, and another where it is magnetically coupled to a Bose condensate. The first example emphasizes that such an interaction can generate parametric squeezing and entanglement. The second scheme demonstrates that the back action of BEC spin measurements can be used to generate quantum states of motion of a mechanical oscillator. We then discuss possible methods for measuring the entire density matrix of a mechanical oscillator. The first method achieves the tomographic reconstruction of the mechanical Wigner function by coupling it simultaneously to a classical optical oscillator and a qubit. The second approach involves a state transfer scheme between momentum excitations of a bose-condensate in a cavity and a moving mirror of the cavity that is entirely mediated by the light field. We conclude with a discussion of the broader implications of this work, and some future research directions.
Why are classical theories often sufficient to describe the physics of our world even though everything around us is entirely composed of microscopic quantum systems? The boundary between these two fundamentally dissimilar theories remains an unsolved problem in modern physics. Position measurements of small objects allow us to probe the area where the classical approximation breaks down. In quantum mechanics, Heisenbergâ s uncertainty principle dictates that any measurement of the position must be accompanied by measurement induced back-action---in this case manifested as an uncertainty in the momentum. In recent years, cavity optomechanics has become a powerful tool to perform precise position measurements and investigate their fundamental limitations. The utilization of optical micro-cavities greatly enhances the interaction between light and state-of-the-art nanomechanical oscillators. Therefore, quantum mechanical phenomena have been successfully observed in systems far beyond the microscopic world. In such a cavity optomechanical system, the fluctuations in the position of the oscillator are transduced onto the phase of the light, while fluctuations in the amplitude of the light disturb the momentum of the oscillator during the measurement. As a consequence, correlations are established between the amplitude and phase quadrature of the probe light. However, so far, observation of quantum effects has been limited exclusively to cryogenic experiments, and access to the quantum regime at room temperature has remained an elusive goal because the overwhelming amount of thermal motion masks the weak quantum effects. This thesis describes the engineering of a high-performance cavity optomechanical device and presents experimental results showing, for the first time, the broadband effects of quantum back-action at room temperature. The device strongly couples mechanical and optical modes of exceptionally high quality factors to provide a measurement sensitivity ∼104 times below the requirement to resolve the zero-point fluctuations of the mechanical oscillator. The quantum back-action is then observed through the correlations created between the probe light and the motion of the nanomechanical oscillator. A so-called â variational measurementâ , which detects the transmitted light in a homodyne detector tuned close to the amplitude quadrature, resolves the quantum noise due to these correlations at the level of 10\% of the thermal noise over more than an octave of Fourier frequencies around mechanical resonance. Moreover, building on this result, an additional experiment demonstrates the ability to achieve quantum enhanced metrology. In this case, the generated quantum correlations are used to cancel quantum noise in the measurement record, which then leads to an improved relative signal-to-noise ratio in measurements of an external force. In conclusion, the successful observation of broadband quantum behavior on a macroscopic object at room temperature is an important milestone in the field of cavity optomechanics. Specifically, this result heralds the rise of optomechanical systems as a platform for quantum physics at room temperature and shows promise for generation of ponderomotive squeezing in room-temperature interferometers.
In a nutshell, a cavity optomechanical system consists of a mechanical oscillator inside an optical cavity. Cavity optomechanics studies the interplay between the light-matter radiation-pressure interaction and the change in the cavity frequency induced by mechanical motion. By leveraging the tools of quantum optics and quantum measurement, cavity quantum optomechanics enables the engineering of nonclassical quantum states of bulk matter. In this thesis, I present protocols for engineering such nonclassical quantum states in Part II. First, I introduce a scheme to ‘grow’ a quantum kitten state of a mechanical oscillator into a macroscopic Schrödinger cat state using a series of nonlinear pulsed optomechanical interactions. Next, I detail our proposed schemes to generate and verify entanglement between two mechanical oscillators. Moving on from pulsed optomechanics, I describe the theory behind an experiment that achieved multi-phonon subtraction from a mechanical oscillator in a continuously driven Brillouin optomechanical system. In the final chapter of Part II, I provide a theoretical preview of an experiment that investigates the behaviour of the mechanical oscillator when no light is detected at the output. In Part III, I introduce a new framework for nonlinear cavity quantum optomechanics that incorporates the intrinsic nonlinearity of the radiation-pressure interaction, the nonlinearity from the cavity enhancement, and higher-order mechanical position terms in the expansion of the cavity frequency. I then propose a scheme for measuring mechanical position using general-dyne detection, applicable to pulsed and continuous measurements. This predicts a new regime of operation, the “stochastic Gaussian” regime. Finally, I discuss a protocol for deterministic mechanical squeezing that utilizes the cavity response.
In the past several years, the field of optomechanics has progressed from proof-of-principle experiments to the realization of mechanical oscillators and measurements in the quantum regime. Mechanical oscillators are of great interest because they can have small dissipation rates, can couple to many different systems of interest, and are the fundamental elements of ultrasensitive force detectors. Coupling these mechanical oscillators to microwave or optical fields provides a twofold advantage. Firstly, information about mechanical position can be encoded in the interrogating field, enabling sensitive readout of the mechanical oscillator. Secondly, the radiation pressure force of that field can be used to control the state of the mechanical oscillator. Including a high-quality microwave or optical cavity enhances both of these effects, as the field strength is resonantly increased.\nThe major questions in the field of optomechanics in the last several years have dealt with using mechanical oscillators for ultrasensitive measurements and as tools for quantum information. Both of these goals have the prerequisite that we be able to read out the motion of the mechanical oscillator in a quantum efficient manner. To that end, we developed a nearly shot-noise limited microwave interferometer capable of measuring mechanical motion with an imprecision below that at the standard quantum limit. This achievement is not only a critical improvement for the electromechanical experiments we do, but is also an important tool for any experiment that encodes the information of interest in microwave fields. In order to use mechanical oscillators as tools for quantum information, the mechanical oscillator must also be cooled into the quantum regime and fully controllable by the interrogating fields. To this end, we used the radiation pressure of microwave fields to cool our macroscopic mechanical oscillator to less than one phonon. We also demonstrated coherent transfer between itinerant microwave states and the mechanical oscillator, even for incident fields with less than one photon of energy.\nThese accomplishments have set the foundation for further experiments to extend the quantum information abilities of optomechanical systems, couple diverse quantum systems via a mechanical intermediary, and potentially explore the foundations of quantum mechanics at macroscopic scales.
In this review, the authors study how a hybrid optomechanical system (OMS), in which a quantum micro- or nano-mechanical oscillator is coupled to the electromagnetic radiation pressure, consisting of an ensemble of ultracold atoms or an atomic Bose–Einstein condensate, can be used as an ultraprecision quantum sensor for measuring very weak signals. As is well-known in any precise quantum measurement, the competition between the shot noise and the backaction noise of measurement executes a limitation on the measurement precision which is the so-called standard quantum limit (SQL). In the case where the intensity of the signal is even lower than the SQL, one needs to perform an ultraprecision quantum sensing to beat the SQL. For this purpose, the authors review three important methods for surpassing the SQL in a hybrid OMS: (i) the backaction evading measurement of a quantum nondemolition variable of the system, (ii) the coherent quantum backaction noise cancelation, and (iii) the so-called parametric sensing, the simultaneous signal amplification, and added noise suppression below the SQL. Furthermore, the authors have shown in this article for the first time how the classical fluctuation of the driving laser phase, the so-called laser phase noise, affects the power spectrum of the output optical field in a standard OMS and induces an additional impression noise which makes the total system noise increase above the SQL. Also, for the first time in this review it has been shown that in the standard OMSs, it is impossible to amplify the signal while suppressing the noise below the SQL simultaneously.