ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
ENGLISH ABSTRACT: Superconductor electronics have shown great promise for interfacing quantum computers to conventional electronics. Several superconductor logic families show potential, \nbut one particular logic family has shown reliable results: Rapid Single Flux Quantum \n(RSFQ). RSFQ logic implements single SFQ pulses to represent binary data instead of \nthe traditional voltage levels used by semiconductor electronics. RSFQ is so ubiquitous \nto superconductor digital systems that it serves as the entry to superconductor digital \ndesign. Presently, however, the field of RSFQ logic cell design is very exclusive with \na small number of physicists and engineers able to design efficient RSFQ cells. This \nresearch aims to provide a formalised RSFQ design methodology with education quality \ncircuit theory. Several RSFQ examples are designed, analysed and improved using phasebased circuit equations. Similar to Kirchhoff’s current and voltage laws, these phase-based \nequations can be used to accurately determine the current distribution within a cell. The \ndesign methodology for multi-state RSFQ cells is also discussed. Multiple simulation \nmethods confirming cell functionality and operating margins are also presented. The \neducation regarding the design, analysis and implementation of RSFQ cells is vastly \nexpanded through this research which can accelerate the field of quantum circuit design. \nRSFQ cells can be connected using a non-storing inductive loop, Josephson transmission lines (JTLs) or, alternatively, superconductor passive transmission lines (PTLs) \nto bridge longer distances. Signal transmission of SFQ pulses through PTLs and JTLs \nare analysed and compared. Impedance matching for PTL interconnects to reduce pulse \nreflection is also investigated. \nAn example of a portable RSFQ cell library for layout synthesis is developed as \npart of the IARPA SuperTools program. The challenges of RSFQ cell layouts for the \nMassachusetts Institute of Technology Lincoln Laboratory (MIT-LL) SFQ5ee fabrication \nprocess are discussed. A methodology for establishing a standardised cell layout synthesis \nis presented. The research contributes to the design and characterisation of track routing \narchitecture for RSFQ on a multilayer fabrication process. \nLastly, methods to test fabricated RSFQ circuits are presented. This includes testing \nthe functionality of individual cells, as well as measuring throughput delays. As the SFQ \npulses are only a few picoseconds wide, it is not possible to observe these pulses using \nconventional measuring equipment. The fabricated tests must therefore be designed in \nsuch a way that it is possible to extract meaningful measurements.
ENGLISH ABSTRACT: Rapid Single Flux Quantum (RSFQ) cells are key in the design of complex and applicable RSFQ electronic circuits. These cells are low-level circuit elements that are used repeatedly to build larger, applicable RSFQ circuitry. Making these cells simple to layout and manufacture, but reliable for extensive use demands a careful development process for RSFQ cells. Cell functionality is verified through simulations, thereafter the cell is laid out in special software packages. Inductance of on-chip superconductor structures is extracted through careful modelling with numerical field solver software. A cell library has been developed by incorporating existing or published cells after further analysis and optimization, as well as developing new cells. Cells that have been adapted into the library include the Josephson transmission line (JTL), Splitter, Merger, D-Flip Flop (DFF), T-Flip Flop (TFF), NOT, AND, OR and XOR, DC-SFQ and SFQ-DC and PTL Driver and Receivers. New cells include NOR, NAND and XNOR. The cells were designed for the IPHT’s RSFQ1D 1kA/cmª and Hypres’ 4.5kA/cmª processes. The cells in the library have good bias current operating margins obtained through simulations (> ±26%). All cells have all the parameters listed in the thesis including extracted inductance values. In order to have a complete and verified RSFQ cell library, cells have been sent for fabrication at IPHT and Hypres facilities. These cells can now be tested on-chip, in the laboratory, to establish functionality and practical bias current margins. All test signal patterns and bias currents required for testing are defined to allow co-workers or collaborators to test the cells.
The ColdFlux project, within the IARPA SuperTools program, aims to develop an open-source EDA tool suite for superconductor circuits, with focus on Rapid single flux quantum (RSFQ) and Adiabatic quantum-flux-parametron (AQFP) logic. The functionality of the ColdFlux tool suite is validated through the development of ready-to-use cell libraries. The process of establishing the open-source ColdFlux RSFQ cell library is documented, along with the set of EDA tools developed within the project required for each step. This includes the initial cell design using phase-based equations, circuit simulation, operating margin analysis, and cell parameter optimization. The row-based layout architecture for the RSFQ cell library is also presented. Several of the designed RSFQ cells are placed within test circuits and fabricated through the MIT-LL SFQ5ee fabrication process. We present the measured results for these test circuits and discuss design efficiency, potential improvements, and future work.
In contrast to transistor-based semiconductor circuits, there is currently no widely accepted formalized circuit theory or design methodology for superconductor rapid single flux quantum (RSFQ) logic circuits. Experienced designers intuitively consider flux loops, nodal phase, and branch currents when making design choices, but the lack of a formalized design process makes it difficult for inexperienced RSFQ circuit designers to construct a functioning logic cell without a reference. This results in new circuit designers, mostly recycling templates from published circuit designs without fully understanding why the circuits function as they do. Inexperienced RSFQ circuit designers often follow an iterative process where cell parameter values are adjusted, and the cell is run through electronic simulation engines until the desired functionality is reached. We propose the development of a formalized circuit design theory for RSFQ logic from first principles using phase-based circuit analysis. The circuit is designed using dc analysis to establish the dc operating point of the circuit. Phase-based analysis and simulation are then used to verify the dynamic circuit functionality. To demonstrate this method, we discuss examples for well-known RSFQ cells. We analyze the initial operating margins of these designs and discuss design accuracy and efficiency. Methods for current regulation to minimize current leakage between cells are discussed. We also present how this design methodology can be used to design new circuits such as an RSFQ XNOR cell. We investigate how an inverting (NOT) cell can be combined with other logic cells to minimize cell latency.
The introduction of passive-transmission-line (PTL) wiring to large-scale SFQ logic circuits offers several advantages over traditional Josephson-transmission-line (JTL) wiring, such as smaller wiring area, less delay, lower power consumption, and more freedom in routing. PTL wiring can drastically change the style of designing SFQ logic circuits. We propose a new methodology for designing large-scale SFQ circuits using PTL wiring. Aiming at generalizing SFQ circuit design, we chose synchronous clocking. We developed a placer that was suitable for SFQ circuit design to assist us with the new design methodology. The placer first synthesizes an H-tree clock distribution network, placing SFQ pulse splitter cells at each branch. It then places logic cells to minimize the maximum length of data PTL wires, aiming at higher operating speeds. Finally, a router completes the PTL wiring. To evaluate the design methodology we designed an 8-bit general purpose RISC processor. Within twelve hours, we obtained a 15-mm-square SFQ circuit that could operate up to 27.6 GHz. We adopted an advanced Nb process, which was characterized by a critical current density of 10 kA/cm2, two 5-mum-wide PTL wiring layers, and a minimum cell size of 30 mum times 30 mum. The circuit consisted of about 20,000 logic cells, which approximated more than 400,000 Josephson junctions including splitters to distribute the clock signal.
An automated layout design flow for rapid single-flux-quantum circuits is proposed in this article. In order to realize small circuit area and low latency, both Josephson transmission lines (JTLs) and passive transmission lines (PTLs) are used for interconnects. Placement and routing are performed considering effective use of JTLs and PTLs. Logic cells are grouped into clusters, and JTLs are used inside clusters. PTLs are used among clusters. The placement process is composed of three steps: first, cell clustering, second, cell placement and JTL routing in each cluster, and third, cluster placement. After the placement process, routing among clusters are performed using PTLs. We applied the proposed design flow to sample circuits with several hundreds of gates. Though the circuit area is not fully optimized, the latency of the circuits designed by the proposed design flow are lower than those of the circuits designed manually.
We have proposed a cell-based design approach for rapid single flux quantum (RSFQ) logic circuits. In our design approach, a binary decision diagram (BDD) is used for representation of logical functions in order to reduce the number of gates. We have made a standard cell library, which is composed of only five basic cells. We add one-junction Josephson transmission line (JTL) to the edge of the input and the output node of some basic cells, by which no deterioration of the DC bias margin is observed for the connection of each cell. In the layout level, the size and the position of the input/output node of each cell are equalized. The standard cell circuits were fabricated by NEC 2.5 kA/cm/sup 2/ and Hypres 1.0 kA/cm/sup 2/ Nb standard process and they were tested at low speed.