Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optics Express

Waveguide integrated hot electron bolometer for classical and quantum photonics

F. Martini, Sara Cibella, Alessandro Gaggero, F. Mattioli, Roberto Leoni

Published Dec 21, 2020• 8 citations
Publisher

Abstract

The development of performant integrated detectors, which are sensitive to quantum fluctuations of coherent light, are strongly desired to realize a scalable and determinist photonic quantum processor based on continuous variables states of light. Here, we investigate the performance of hot electron bolometers (HEBs) fabricated on top of a silicon-on-insulator (SOI) photonic circuit showing responsivities up to 8600 V/W and a record noise equivalent temperature of 1.1 dB above the quantum limit. Thanks to a detailed analysis of the noise sources of the waveguide integrated HEB, we estimate 14.8 dBV clearance between the shot noise and electrical noise with just 1.1µW of local oscillator power. The full technology compatibility with superconducting nanowire single photon detectors (SNSPDs) opens the possibility of nonclassical state engineering and state tomography performed within the same platform, enabling a new class of optical quantum processors.

DOI
10.1364/oe.410317

Related papers

Waveguide-integrated niobium- nitride detectors for on-chip quantum nanophotonics

F. Mattioli, Sara Cibella, Alessandro Gaggero +2 more

NbN-based detectors can detect light from the granular regime (single or few photons) up to weak continuous photon fluxes at wavelengths ranging from visible light up to mid-IR. The article reports our recent results on a novel linear detector, the waveguide-integrated hot electron bolometer (HEB) capable to measure photon fluxes of large coherent beams in a regime in which superconducting nanowire single photon detectors (SNSPDs) are not efficient due to their strong nonlinearity. SNSPDs, photon number resolving detectors and amplitude multiplexing readout schemes, all integrated on photonic circuits are also discussed in the paper. The compatibility of the integrated HEB detectors with the SNSPDs technology can allow the characterization of complex non classical states of light within the same chip.

Nanotechnology•Nov 20, 2020•3 citations

Shot-Noise Limited Hot Electron Bolometer Integrated on Silicon-On-Insulator Photonics

F. Martini, Sara Cibella, Alessandro Gaggero +2 more

Shot-noise limited (SNL) detectors that can be integrated on several photonic platforms are essential for photonic quantum technologies. We integrated small-area Hot Electron Bolometers on SOI photonics, demonstrating SNL operations with only 1.1μW of input power.

Conference on Lasers and Electro-Optics•Jan 1, 2021•0 citations

Waveguide-integrated superconducting nanowire single-photon detectors

Filippo Martinelli

Advancements in integrated photonics have enabled the miniaturization and scaling of complex photonic circuits, providing stability and reliability beyond the capabilities of conventional bulk setups. A central component of quantum photonic circuits is the single-photon detector, responsible for quantum state measurement. Due to the stringent performance requirements of quantum applications, superconducting nanowire single-photon detectors (SNSPDs) have emerged as the preferred detection technology, offering superior efficiency, low noise, and high timing resolution. While tabletop SNSPDs are now mature, commercially available and contributed to significant progress in quantum computing and communication, their integration into photonic circuits is still in its infancy. Integrated SNSPDs have shown the potential to not only match but surpass tabletop detectors in several performance metrics. Nevertheless, demonstrations have largely focused on individual integrated detectors, with limited investigation into more complex integrated circuits and advanced functionalities. In this thesis, we present a novel integration platform based on photonic bound states in the continuum (BICs) to address a critical limitation of conventional SNSPD designs, where nanowires placed directly atop the waveguide core are constrained by the core geometry. The etchless nature of our BIC waveguides provides a flat surface that decouples the design of the electronic readout circuitry below from the optical circuit layer above, enabling innovative integrated-nanowire geometries and facilitating large-scale integration of SNSPDs with CMOS-compatible circuits. We established a complete fabrication and characterization workflow for integrating NbTiN-based superconducting nanowires with BIC waveguides. Our integrated detectors achieved state-of-the-art performance, including detection efficiencies exceeding 70%, intrinsic jitter below 70 ps, and ultrafast recovery times (~1.7 ns). These results pave the way toward GHz-rate quantum state measurements, essential for scalable quantum photonic processors. Leveraging the design flexibility of BIC waveguides, we introduce the concept of inline detection with SNSPDs which exploits their unique ability to precisely engineer absorption through nanowire length control. By cascading multiple partially absorbing SNSPDs, it is possible to significantly reduce the number of required optical components and miniaturize complex quantum measurement setups within an extremely compact footprint. Traditional integration geometries prevent such implementations due to significant scattering losses at nanowire terminations, which limit the feasibility of cascaded designs. On the other hand, the design flexibility provided by our BIC platform makes it ideal for development of inline detection schemes. As a proof-of-concept, we use inline detection to miniaturize two fundamental quantum optics tools: an integrated Hanbury Brown and Twiss (HBT) interferometer and a photon-number-resolving (PNR) detector. We replicated the functionalities of these setups using only two nanowires integrated along a single waveguide. These devices show extremely compact footprint, highlighting the scalability potential of our approach. We validated these devices through characterization of a single-photon source and the discrimination of collinear photon pairs. The experimental results aligned well with previous literature and theoretical predictions, confirming the reliability of our integration method. Overall, this work presents a novel approach to quantum measurements within integrated quantum photonic circuits. Inline detection represents a step forward in quantum integrated photonics, moving from individual device demonstrations toward functional quantum circuits. By introducing our BIC-based integration platform, we simplify detector design and fabrication, lowering barriers to the development of inline detection circuits and opening new opportunities in multiphoton quantum state measurements, single-photon spectroscopy, and multiphoton subtraction.

•Jan 1, 2025•0 citations

4-Pixel NbN Hot-Electron Bolometer Integrated in a Si$_3$N$_4$ Planar Optical Waveguide with On-Chip Fiber-Alignment Trench

N. A. Vovk, G. A. Matveev, M. A. Mumlyakov +7 more

In this work, we design and characterize a 4-pixel superconducting hot-electron bolometer (HEB) based on niobium nitride (NbN), integrated with individual planar silicon nitride (Si$_3$N$_4$) waveguides. The implemented architecture enables simultaneous detection of an optical signal in four independent channels. To efficiently couple optical radiation under cryogenic conditions, we employ an edge (end-fire) coupling approach using dedicated U-shaped grooves that provide accurate and stable positioning of an optical fiber with respect to the on-chip waveguide facet. The device responsivity is measured as a function of the HEB operating point. The measured voltage responsivity reaches $3800~\mathrm{V/W}$ at a modulation frequency of $3~\mathrm{GHz}$. We demonstrate detection of optically modulated signals in the gigahertz range. The developed fabrication route is promising for compact integrated receiver systems and low-noise cryogenic microwave transducers, including superconducting nanowire single-photon detectors (SNSPDs).

arXiv:2603.01676•Mar 2, 2026•0 citations

4-pixel NbN hot-electron bolometer integrated in a Si 3 N 4 planar optical waveguide with on-chip fiber-alignment trench

Nikolay A. Vovk, G. Matveev, Alexander M. Mumlyakov +7 more

Abstract In this work, we design and characterize a 4-pixel superconducting hot-electron bolometer (HEB) based on niobium nitride (NbN), integrated with individual planar silicon nitride (Si 3 N 4 ) waveguides. The implemented architecture enables simultaneous detection of an optical signal in four independent channels. To efficiently couple optical radiation under cryogenic conditions, we employ an edge (end-fire) coupling approach using dedicated U-shaped grooves that provide accurate and stable positioning of an optical fiber with respect to the on-chip waveguide facet. The device responsivity is measured as a function of the HEB operating point. The measured voltage responsivity reaches 3800 V W − 1 at a modulation frequency of 3 GHz . We demonstrate detection of optically modulated signals in the gigahertz range. The developed fabrication route is promising for compact integrated receiver systems and low-noise cryogenic microwave transducers, including superconducting nanowire single-photon detectors.

Superconductor Science and Technology•Jun 15, 2026•0 citations

Waveguide integrated superconducting single-photon detectors with high internal quantum efficiency at telecom wavelengths

Oliver Kahl, Simone Ferrari, Vadim V. Kovalyuk +3 more

Superconducting nanowire single-photon detectors (SNSPDs) provide high efficiency for detecting individual photons while keeping dark counts and timing jitter minimal. Besides superior detection performance over a broad optical bandwidth, compatibility with an integrated optical platform is a crucial requirement for applications in emerging quantum photonic technologies. Here we present SNSPDs embedded in nanophotonic integrated circuits which achieve internal quantum efficiencies close to unity at 1550 nm wavelength. This allows for the SNSPDs to be operated at bias currents far below the critical current where unwanted dark count events reach milli-Hz levels while on-chip detection efficiencies above 70% are maintained. The measured dark count rates correspond to noise-equivalent powers in the 10(-19) W/Hz(-1/2) range and the timing jitter is as low as 35 ps. Our detectors are fully scalable and interface directly with waveguide-based optical platforms.

Scientific Reports•Jun 10, 2015•111 citations
The development of performant integrated detectors, which are sensitive to quantum fluctuations of coherent light, are strongly desired to realize a scalable and determinist photonic quantum processor based on continuous variables states of light. Here, we investigate the performance of hot electron bolometers (HEBs) fabricated on top of a silicon-on-insulator (SOI) photonic circuit showing responsivities up to 8600 V/W and a record noise equivalent temperature of 1.1 dB above the quantum limit. Thanks to a detailed analysis of the noise sources of the waveguide integrated HEB, we estimate 14.8 dBV clearance between the shot noise and electrical noise with just 1.1µW of local oscillator power. The full technology compatibility with superconducting nanowire single photon detectors (SNSPDs) opens the possibility of nonclassical state engineering and state tomography performed within the same platform, enabling a new class of optical quantum processors.
NbN-based detectors can detect light from the granular regime (single or few photons) up to weak continuous photon fluxes at wavelengths ranging from visible light up to mid-IR. The article reports our recent results on a novel linear detector, the waveguide-integrated hot electron bolometer (HEB) capable to measure photon fluxes of large coherent beams in a regime in which superconducting nanowire single photon detectors (SNSPDs) are not efficient due to their strong nonlinearity. SNSPDs, photon number resolving detectors and amplitude multiplexing readout schemes, all integrated on photonic circuits are also discussed in the paper. The compatibility of the integrated HEB detectors with the SNSPDs technology can allow the characterization of complex non classical states of light within the same chip.
Advancements in integrated photonics have enabled the miniaturization and scaling of complex photonic circuits, providing stability and reliability beyond the capabilities of conventional bulk setups. A central component of quantum photonic circuits is the single-photon detector, responsible for quantum state measurement. Due to the stringent performance requirements of quantum applications, superconducting nanowire single-photon detectors (SNSPDs) have emerged as the preferred detection technology, offering superior efficiency, low noise, and high timing resolution. While tabletop SNSPDs are now mature, commercially available and contributed to significant progress in quantum computing and communication, their integration into photonic circuits is still in its infancy. Integrated SNSPDs have shown the potential to not only match but surpass tabletop detectors in several performance metrics. Nevertheless, demonstrations have largely focused on individual integrated detectors, with limited investigation into more complex integrated circuits and advanced functionalities. In this thesis, we present a novel integration platform based on photonic bound states in the continuum (BICs) to address a critical limitation of conventional SNSPD designs, where nanowires placed directly atop the waveguide core are constrained by the core geometry. The etchless nature of our BIC waveguides provides a flat surface that decouples the design of the electronic readout circuitry below from the optical circuit layer above, enabling innovative integrated-nanowire geometries and facilitating large-scale integration of SNSPDs with CMOS-compatible circuits. We established a complete fabrication and characterization workflow for integrating NbTiN-based superconducting nanowires with BIC waveguides. Our integrated detectors achieved state-of-the-art performance, including detection efficiencies exceeding 70%, intrinsic jitter below 70 ps, and ultrafast recovery times (~1.7 ns). These results pave the way toward GHz-rate quantum state measurements, essential for scalable quantum photonic processors. Leveraging the design flexibility of BIC waveguides, we introduce the concept of inline detection with SNSPDs which exploits their unique ability to precisely engineer absorption through nanowire length control. By cascading multiple partially absorbing SNSPDs, it is possible to significantly reduce the number of required optical components and miniaturize complex quantum measurement setups within an extremely compact footprint. Traditional integration geometries prevent such implementations due to significant scattering losses at nanowire terminations, which limit the feasibility of cascaded designs. On the other hand, the design flexibility provided by our BIC platform makes it ideal for development of inline detection schemes. As a proof-of-concept, we use inline detection to miniaturize two fundamental quantum optics tools: an integrated Hanbury Brown and Twiss (HBT) interferometer and a photon-number-resolving (PNR) detector. We replicated the functionalities of these setups using only two nanowires integrated along a single waveguide. These devices show extremely compact footprint, highlighting the scalability potential of our approach. We validated these devices through characterization of a single-photon source and the discrimination of collinear photon pairs. The experimental results aligned well with previous literature and theoretical predictions, confirming the reliability of our integration method. Overall, this work presents a novel approach to quantum measurements within integrated quantum photonic circuits. Inline detection represents a step forward in quantum integrated photonics, moving from individual device demonstrations toward functional quantum circuits. By introducing our BIC-based integration platform, we simplify detector design and fabrication, lowering barriers to the development of inline detection circuits and opening new opportunities in multiphoton quantum state measurements, single-photon spectroscopy, and multiphoton subtraction.
4-Pixel NbN Hot-Electron Bolometer Integrated in a Si3_33​N4_44​ Planar Optical Waveguide with On-Chip Fiber-Alignment Trench
In this work, we design and characterize a 4-pixel superconducting hot-electron bolometer (HEB) based on niobium nitride (NbN), integrated with individual planar silicon nitride (Si3_33​N4_44​) waveguides. The implemented architecture enables simultaneous detection of an optical signal in four independent channels. To efficiently couple optical radiation under cryogenic conditions, we employ an edge (end-fire) coupling approach using dedicated U-shaped grooves that provide accurate and stable positioning of an optical fiber with respect to the on-chip waveguide facet. The device responsivity is measured as a function of the HEB operating point. The measured voltage responsivity reaches 3800 V/W3800~\mathrm{V/W}3800 V/W at a modulation frequency of 3 GHz3~\mathrm{GHz}3 GHz. We demonstrate detection of optically modulated signals in the gigahertz range. The developed fabrication route is promising for compact integrated receiver systems and low-noise cryogenic microwave transducers, including superconducting nanowire single-photon detectors (SNSPDs).
Abstract In this work, we design and characterize a 4-pixel superconducting hot-electron bolometer (HEB) based on niobium nitride (NbN), integrated with individual planar silicon nitride (Si 3 N 4 ) waveguides. The implemented architecture enables simultaneous detection of an optical signal in four independent channels. To efficiently couple optical radiation under cryogenic conditions, we employ an edge (end-fire) coupling approach using dedicated U-shaped grooves that provide accurate and stable positioning of an optical fiber with respect to the on-chip waveguide facet. The device responsivity is measured as a function of the HEB operating point. The measured voltage responsivity reaches 3800 V W − 1 at a modulation frequency of 3 GHz . We demonstrate detection of optically modulated signals in the gigahertz range. The developed fabrication route is promising for compact integrated receiver systems and low-noise cryogenic microwave transducers, including superconducting nanowire single-photon detectors.
Superconducting nanowire single-photon detectors (SNSPDs) provide high efficiency for detecting individual photons while keeping dark counts and timing jitter minimal. Besides superior detection performance over a broad optical bandwidth, compatibility with an integrated optical platform is a crucial requirement for applications in emerging quantum photonic technologies. Here we present SNSPDs embedded in nanophotonic integrated circuits which achieve internal quantum efficiencies close to unity at 1550 nm wavelength. This allows for the SNSPDs to be operated at bias currents far below the critical current where unwanted dark count events reach milli-Hz levels while on-chip detection efficiencies above 70% are maintained. The measured dark count rates correspond to noise-equivalent powers in the 10(-19) W/Hz(-1/2) range and the timing jitter is as low as 35 ps. Our detectors are fully scalable and interface directly with waveguide-based optical platforms.