Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Physics Conference Series

Performance of Digital SQUID with Sub-Flux Quantum Feedback Resolution Fabricated using 10 kA/cm2 Nb Process

Kohki Itagaki, Itta Oshima, Yuichi Hasegawa, Ryo Matsunawa, Masato Naruse, Tohru Taino, Hiroaki Myoren

Published Jul 1, 2020• 0 citations
Publisher

Abstract

Abstract Digital superconducting quantum interference device (SQUID with Single Flux Quantum (SFQ) feedback operates as a Δ-type oversampling A/D converter. Magnetic flux resolution at Nyquist frequency can be improved by taking sub SFQ feedback resolution and large oversampling ratio. Using high critical current density Nb process for fabricating SFQ circuits, we expected more higher operation speed for the digital SQUID and resulting to higher magnetic flux resolutions. We expected a performance of the digital SQUID magnetometer fabricated using 10 kA/cm2 Nb process based on CAD layout, with an up/down counter using T2FF cells and parallel SFQ feedback. For the clock frequency of 13 GHz and the Nyquist frequency of 1.587 MHz, the magnetic field noise was lower than 1.5 fT / Hz and the slew rate was exceeded 500 mT/s.

DOI
10.1088/1742-6596/1590/1/012038

Related papers

Design and Magnetic Field Noise of Magnetometer Using Digital SQUID With Subflux Quantum Feedback

Hiroaki Myoren, Kouhei Takatoku, Masato Naruse +1 more

Digital superconducting quantum interference devices (SQUIDs) based on single-flux quantum (SFQ) logic have attractive characteristics such as wide dynamic ranges and high slew rates. However, the resolution of a typical digital SQUID is limited by SFQ feedback. To realize lower magnetic field noise by magnetometers using digital SQUIDs, we have adopted two feedback combinations: one, utilizing the SFQ input/output for a main loop and the other, using a mutually coupled loop. The main loop receives direct Φ0feedback and subflux quantum feedback Φ0/n, where n is an integer from the mutually coupled loop. The flux resolution for the digital SQUID shows improvement with increasing n and reaches below 40 mΦ0at n = 210; however, the slew rate decreases with increasing n and reaches 1.22 × 106Φ0/s at fc= 1.25 GHz and n = 210. For a magnetometer using a digital SQUID with a pickup loop, we confirmed a magnetic field noise of less than 100 fT/√Hz with a signal bandwidth of 1 MHz for operation frequency fcof 20 GHz.

IEEE Transactions on Applied Superconductivity•May 20, 2016•7 citations

High-Resolution Digital SQUID Magnetometer using Sub-Flux Quantum Feedback

Hiroaki Myoren, Kosuke Okabe, Ryo Matsunawa +3 more

Abstract Digital SQUIDs with the single flux quantum (SFQ) feedback have attracted much attention because of the feasibility of realizing a wide dynamic range and high slew rate for digital magnetometers. In order to realize higher resolution, we have studied a digital SQUID with sub-flux quantum feedback. Combining the sub-flux quantum feedback to a feedback loop and the direct SFQ feedback to a main loop triggered by carry SFQ pulses from an up/down counter. In this study, we discuss the method of multi-flux quantum generation and compact design of the SFQ up/down counter for high-speed operation of the digital SQUID magnetometer.

Journal of Physics Conference Series•Jun 1, 2020•0 citations

Design and Performance of Digital SQUID with Sub-Flux Quantum Resolution

Hiroaki Myoren, Kouhei Takatoku, Masato Naruse +1 more

Digital SQUIDs based on the single flux quantum (SFQ) logic have attractive characteristics, such as wide dynamic range and high slew rate. However, the resolution of digital SQUIDs is limited to SFQ. To realize sub-flux quantum resolution for these SQUIDs, we have adopted two types of feedback combinations: one with the SFQ input/output for a main loop and the other with a mutually coupled loop. The main loop receives direct Φ0feedback and sub-flux quantum feedback Φ0/n, where n is an integer, from the mutually coupled loop. We confirmed the correct operation of our device at a clock frequency of 1.25 GHz for a digital SQUID with a sub-Φ0flux feedback resolution of Φ0/8 from circuit simulation. The slew rate is found to be 1.56×108Φ0/s in this simulation (fc=1.25 GHz, n=8). The flux resolution for the digital SQUID shows improvement with increasing n and reached below 40 mΦ0with n=210; however the slew rate is decreased with increasing n and reached 1.22×106Φ0/swith fc=1.25 GHz and n=210.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•2 citations

Characterization of a digital squid for magnetic field measurements with high dynamic range

Imke Haverkamp, Olaf Wetzstein, J. Kunert +3 more

Measurements of extremely weak magnetic fields in unshielded environments require sensors providing a high dynamic range and slew rate while maintaining a high resolution. At present, analog Superconducting Quantum Interference Devices (SQUIDs) are the most sensitive sensors for magnetic flux. Due to their room-temperature feedback electronics necessary to maintain a stable point of operation, slew rates of those sensors are limited. The dynamic range is usually restricted by the resolution of classical analog to digital converters. The digital SQUID follows a different approach: a change of the magnetic field penetrating the pickup loop is translated by the sensor into a stream of voltage pulses. Each pulse represents the change of the magnetic flux inside the pickup loop by one flux quantum Φ0. By fast counting of these flux quanta, it is possible to outperform the analog SQUID in terms of dynamic range and maximum slew rate. We present our latest results with respect to the internal mechanisms of the digital SQUID and present a method to compensate the main source for nonlinear behavior of the sensor. The analyzed circuit was fabricated by FLUXONICS Foundry (1) in a 1 kA/cm² niobium fabrication process.

Elektronika : konstrukcje, technologie, zastosowania•Jan 1, 2011•1 citation

Performance of Digital SQUID with Sub-Flux Quantum Feedback Resolution fabricated using 10 kA/cm2 Nb process

Kouki Itagaki, Ryo Matsunawa, Itta Oshima +4 more

IEICE Technical Report; IEICE Tech. Rep.•Aug 2, 2019•0 citations

Results on a fast digital DROS

M. Podt, A.J. Mieog, B. G.A. Rolink +2 more

A digital double relaxation oscillation (DROS) superconducting quantum interference device (SQUID) has the potential for a very large dynamic range and a slew rate that is orders of magnitude larger than that of conventional SQUID systems. This is, for example, advantageous when using the SQUID in an unshielded environment. An important characteristic of the digital DROS is that the feedback flux is quantized since this flux is supplied by a superconducting up-down counter. Together with the clock frequency, the quantization unit of the feedback flux determines the maximum slew rate. In an optimized design, the quantization unit is adapted to the broadband flux noise of the DROS, so that the slew rate is maximized without compromising the sensitivity. Simulations on our optimized digital DROS showed proper operation for slew rates up to 5×10 6 Φ 0 s -1 . The relaxation oscillations generated at a frequency of 100 MHz deliver an on-chip clock signal, so that no external clock is required. Slew rates up to 10 8 Φ 0 s -1 can be achieved by increasing the relaxation oscillation frequency to a few GHz. This means that sub-µm 2 Josephson junctions with high critical current densities are required. The first experiments using low- T c ramp-type Josephson junctions are presented in this paper.

Superconductor Science and Technology•Nov 21, 2001•7 citations
Abstract Digital superconducting quantum interference device (SQUID with Single Flux Quantum (SFQ) feedback operates as a Δ-type oversampling A/D converter. Magnetic flux resolution at Nyquist frequency can be improved by taking sub SFQ feedback resolution and large oversampling ratio. Using high critical current density Nb process for fabricating SFQ circuits, we expected more higher operation speed for the digital SQUID and resulting to higher magnetic flux resolutions. We expected a performance of the digital SQUID magnetometer fabricated using 10 kA/cm2 Nb process based on CAD layout, with an up/down counter using T2FF cells and parallel SFQ feedback. For the clock frequency of 13 GHz and the Nyquist frequency of 1.587 MHz, the magnetic field noise was lower than 1.5 fT / Hz and the slew rate was exceeded 500 mT/s.
Digital superconducting quantum interference devices (SQUIDs) based on single-flux quantum (SFQ) logic have attractive characteristics such as wide dynamic ranges and high slew rates. However, the resolution of a typical digital SQUID is limited by SFQ feedback. To realize lower magnetic field noise by magnetometers using digital SQUIDs, we have adopted two feedback combinations: one, utilizing the SFQ input/output for a main loop and the other, using a mutually coupled loop. The main loop receives direct Φ0feedback and subflux quantum feedback Φ0/n, where n is an integer from the mutually coupled loop. The flux resolution for the digital SQUID shows improvement with increasing n and reaches below 40 mΦ0at n = 210; however, the slew rate decreases with increasing n and reaches 1.22 × 106Φ0/s at fc= 1.25 GHz and n = 210. For a magnetometer using a digital SQUID with a pickup loop, we confirmed a magnetic field noise of less than 100 fT/√Hz with a signal bandwidth of 1 MHz for operation frequency fcof 20 GHz.
Abstract Digital SQUIDs with the single flux quantum (SFQ) feedback have attracted much attention because of the feasibility of realizing a wide dynamic range and high slew rate for digital magnetometers. In order to realize higher resolution, we have studied a digital SQUID with sub-flux quantum feedback. Combining the sub-flux quantum feedback to a feedback loop and the direct SFQ feedback to a main loop triggered by carry SFQ pulses from an up/down counter. In this study, we discuss the method of multi-flux quantum generation and compact design of the SFQ up/down counter for high-speed operation of the digital SQUID magnetometer.
Digital SQUIDs based on the single flux quantum (SFQ) logic have attractive characteristics, such as wide dynamic range and high slew rate. However, the resolution of digital SQUIDs is limited to SFQ. To realize sub-flux quantum resolution for these SQUIDs, we have adopted two types of feedback combinations: one with the SFQ input/output for a main loop and the other with a mutually coupled loop. The main loop receives direct Φ0feedback and sub-flux quantum feedback Φ0/n, where n is an integer, from the mutually coupled loop. We confirmed the correct operation of our device at a clock frequency of 1.25 GHz for a digital SQUID with a sub-Φ0flux feedback resolution of Φ0/8 from circuit simulation. The slew rate is found to be 1.56×108Φ0/s in this simulation (fc=1.25 GHz, n=8). The flux resolution for the digital SQUID shows improvement with increasing n and reached below 40 mΦ0with n=210; however the slew rate is decreased with increasing n and reached 1.22×106Φ0/swith fc=1.25 GHz and n=210.
Measurements of extremely weak magnetic fields in unshielded environments require sensors providing a high dynamic range and slew rate while maintaining a high resolution. At present, analog Superconducting Quantum Interference Devices (SQUIDs) are the most sensitive sensors for magnetic flux. Due to their room-temperature feedback electronics necessary to maintain a stable point of operation, slew rates of those sensors are limited. The dynamic range is usually restricted by the resolution of classical analog to digital converters. The digital SQUID follows a different approach: a change of the magnetic field penetrating the pickup loop is translated by the sensor into a stream of voltage pulses. Each pulse represents the change of the magnetic flux inside the pickup loop by one flux quantum Φ0. By fast counting of these flux quanta, it is possible to outperform the analog SQUID in terms of dynamic range and maximum slew rate. We present our latest results with respect to the internal mechanisms of the digital SQUID and present a method to compensate the main source for nonlinear behavior of the sensor. The analyzed circuit was fabricated by FLUXONICS Foundry (1) in a 1 kA/cm² niobium fabrication process.
A digital double relaxation oscillation (DROS) superconducting quantum interference device (SQUID) has the potential for a very large dynamic range and a slew rate that is orders of magnitude larger than that of conventional SQUID systems. This is, for example, advantageous when using the SQUID in an unshielded environment. An important characteristic of the digital DROS is that the feedback flux is quantized since this flux is supplied by a superconducting up-down counter. Together with the clock frequency, the quantization unit of the feedback flux determines the maximum slew rate. In an optimized design, the quantization unit is adapted to the broadband flux noise of the DROS, so that the slew rate is maximized without compromising the sensitivity. Simulations on our optimized digital DROS showed proper operation for slew rates up to 5×10 6 Φ 0 s -1 . The relaxation oscillations generated at a frequency of 100 MHz deliver an on-chip clock signal, so that no external clock is required. Slew rates up to 10 8 Φ 0 s -1 can be achieved by increasing the relaxation oscillation frequency to a few GHz. This means that sub-µm 2 Josephson junctions with high critical current densities are required. The first experiments using low- T c ramp-type Josephson junctions are presented in this paper.