Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Scientific Reports

Photonic Readout of Superconducting Nanowire Single Photon Counting Detectors

Marc de, Emma E. Wollman, Amir Hossein Atabaki, Dodd Joseph Gray, Matthew D. Shaw, Rajeev J. Ram

Published Jun 11, 2020• 40 citations
Publisher

Abstract

Abstract Scalable, low power, high speed data transfer between cryogenic (0.1–4 K) and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1,000–10,000 pm/V) and a low input impedance of 500 Ω with a low power dissipation of 40 μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD.

DOI
10.1038/s41598-020-65971-5

Related papers

Readout of Superconducting Nanowire Single Photon Detectors through Forward Biased Optical Modulators

Marc de, Emma E. Wollman, Amir Hossein Atabaki +3 more

Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm$^2$ range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500 $Ω$ with a low power dissipation of 40 $μ$W. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.

arXiv:2002.00063•Jan 29, 2020•4 citations

Photonic readout of superconducting nanowire single photon counting detectors

Rajeev J. Ram, Marc de, Emma E. Wollman +1 more

Scalable, low power, high speed data transfer between cryogenic and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and allows for very high bandwidth densities by carrying multiple signals through the same physical fiber. By operating a CMOS modulator in the forward bias regime at a temperature of 3.6 K, we have demonstrated the optical readout of a superconducting nanowire single-photon detector (SNSPD) without the need for an interfacing device.

Advanced Photon Counting Techniques•Jun 15, 2023•0 citations

Characterizing All-Optical Biasing and Readout of a Superconducting Opto-Electronic Circuit

Frederik Thiele, Thomas R. Hummel, Julian Brockmeier +6 more

Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jun 26, 2023•0 citations

Opto-electronic bias of a superconducting nanowire single photon detector using a cryogenic photodiode

Frederik Thiele, Thomas Hummel, Maximilian Protte +1 more

Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.

APL Photonics•Aug 1, 2022•9 citations

50 µm diameter superconducting nanowire single-photon detector with sub-17 ps timing jitter and high efficiency for visible wavelengths (Conference Presentation)

Jin Chang, Iman Esmaeil Zadeh

Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.

Quantum Optics and Photon Counting•May 13, 2019•0 citations

Broadband waveguide-integrated superconducting single-photon detectors with high system detection efficiency

Martin A. Wolff, Fabian Beutel, Jonas Schütte +4 more

Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.

Applied Physics Letters•Apr 12, 2021•43 citations
Abstract Scalable, low power, high speed data transfer between cryogenic (0.1–4 K) and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1,000–10,000 pm/V) and a low input impedance of 500 Ω with a low power dissipation of 40 μW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD.
Scalable, high speed data transfer between cryogenic (0.1-4 K) and room temperature environments is instrumental in a broad range of fields including quantum computing, superconducting electronics, single photon imaging and space-based communications. A promising approach to overcome the limitations of conventional wire-based readout is the use of optical fiber communication. Optical fiber presents a 100-1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and is also immune to electromagnetic interference, which allows routing of sensitive signals with improved robustness to noise and crosstalk. Most importantly, optical fibers allow for very high bandwidth densities (in the Tbps/mm2^22 range) by carrying multiple signals through the same physical fiber (Wavelength Division Multiplexing, WDM). Here, we demonstrate for the first time optical readout of a superconducting nanowire single-photon detector (SNSPD) directly coupled to a CMOS photonic modulator, without the need for an interfacing device. By operating the modulator in the forward bias regime at a temperature of 3.6 K, we achieve very high modulation efficiency (1000-10,000 pm/V) and a low input impedance of 500 ΩΩΩ with a low power dissipation of 40 μμμW. This allows us to obtain optical modulation with the low, millivolt-level signal generated by the SNSPD. Optical communication is becoming the preferred I/O solution in modern, room temperature high performance systems, and this work demonstrates its suitability for scalable cryogenic readout, which could help achieve the full potential of superconducting technologies.
Scalable, low power, high speed data transfer between cryogenic and room temperature environments is essential for the realization of practical, large-scale systems based on superconducting technologies. Optical fiber presents a 100–1,000x lower heat load than conventional electrical wiring, relaxing the requirements for thermal anchoring, and allows for very high bandwidth densities by carrying multiple signals through the same physical fiber. By operating a CMOS modulator in the forward bias regime at a temperature of 3.6 K, we have demonstrated the optical readout of a superconducting nanowire single-photon detector (SNSPD) without the need for an interfacing device.
Superconducting nanowire single-photon detectors have become indispensable for experiments in quantum optics and photonic quantum information processing. Nevertheless, these detectors require temperatures below 4 K to operate. These devices typically require coaxial cables as electrical connections for biasing and readout. Replacing these electrical connections with optical fibers both isolates the SNSPD from noise in room-temperature control electronics and simultaneously achieves a connection with a low thermal load. Nevertheless, the optoelectronic interfaces required for this purpose must be fully compatible with the cryogenic operating conditions of the detector. Recently, optical readout of an SNSPD using an electro-optic modulator at cryogenic temperatures has been demonstrated [1]–[3]. In addition, we have shown an opto-electronic bias of an SNSPD by generating the bias current using a photodiode co-located on the cold stage of the cryostat [4]. Both methods replace elements of electrical connection for the SNSPD in the cryostat by an optical fiber. Here, we show the combination of the opto-electronic bias and optical read readout in a single device, which enables us to operate an SNSPD fully isolated from room temperature electronics.
Superconducting Nanowire Single Photon Detectors (SNSPDs) have become an integral part of quantum optics in recent years because of their high performance in single photon detection. We present a method to replace the electrical input by supplying the required bias current via the photocurrent of a photodiode situated on the cold stage of the cryostat. Light is guided to the bias photodiode through an optical fiber, which enables a lower thermal conduction and galvanic isolation between room temperature and the cold stage. We show that an off-the-shelf InGaAs–InP photodiode exhibits a responsivity of at least 0.55 A/W at 0.8 K. Using this device to bias an SNSPD, we characterize the count rate dependent on the optical power incident on the photodiode. This configuration of the SNSPD and photodiode shows an expected plateau in the single photon count rate with an optical bias power on the photodiode above 6.8 µW. Furthermore, we compare the same detector under both optical and electrical bias, and show there is no significant changes in performance. This has the advantage of avoiding an electrical input cable, which reduces the latent heat load by a factor of 100 and, in principle, allows for low loss RF current supply at the cold stage.
Superconducting nanowire single photon detectors (SNSPDs) have demonstrated advantages over traditional detectors in many fields [1]. Most fiber-coupled SNSPDs are coupled to single mode fibers, limiting their usability for applications where large surface area detectors are needed, for example fluorescence detection and satellite-based quantum communication [2][3]. Other important requirements for many applications are broadband detection efficiency, and low timing jitter [4]. So far, the increased meander length of multimode detectors, and the therefore increased kinetic inductance and number of imperfections due to film inhomogeneities have limited the timing jitter [5]. Moreover, combining low timing jitter with high detection efficiency and low dark count rate in one device is challenging due to the tradeoffs between different properties of SNSPDs [6]. In this paper, we achieved high efficiency and strong saturation over a broad wavelength range with a low timing jitter of 16.99 ps while maintaining a low dark count rate of < 0.2 Hz for an SNSPD coupled to a 50 µm core multimode fiber. To enhance the broadband absorption from 405 nm to 830 nm, detectors were fabricated on an optimized SiO2 cavity and Aluminum mirror. The geometry of the nanowire was also tuned to reach a good internal saturation of efficiency over the visible/NIR range but also to carry high current to get a large signal. Furthermore, a cryogenic readout amplifier was optimized to improve the signal to noise ratio and thus lead to high time resolution. Our devices can be readily used to enable higher resolution and faster quantum optics, bio-imaging, laser ranging and other optical experiments.
Fast and efficient detection of single photons with high timing accuracy is a crucial requirement in most quantum optics experiments and enables novel sensing and imaging solutions. Superconducting nanowire single-photon detectors (SNSPD) achieve technology-leading performance in terms of detection efficiency, dark count rate, timing jitter, and detector dead times. However, conventional SNSPDs with high system detection efficiency typically rely on resonant enhancement of the absorption efficiency, thus only achieving attractive detector benchmarks over narrow spectral windows. Waveguide-integrated SNSPDs allow for leveraging the wideband material absorption in superconducting nanowires by absorbing light in a traveling-wave geometry but have been limited to low system detection efficiencies due to interface losses when coupling to optical fibers. Here, we show how high system detection efficiencies of 22%–73% are realized over a broad wavelength range from 532 nm to 1640 nm in a single waveguide-integrated SNSPD device. We accomplish efficient coupling between optical fibers and waveguide-integrated nanowire detectors by employing a 3D interface, produced in direct laser writing, that relies on total internal reflection for achieving a broad transmission bandwidth. We further find low timing jitter of 25.7 ps and detector decay times of 9.8 ns, allowing for single-photon counting with high repetition rates up to 100 MHz. Our work paves the way for an efficient single-photon detector solution that combines the spectral requirements of an extremely wide range of quantum optics experiments in a single device. The coupling approach and SNSPD-integration with nanophotonic circuits are further well-suited for realizing large-scale detector arrays.