Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Investigation of the Effects of 1/fNoise on Superconducting Circuits

Yusuke Tsuna, Yuki Yamanashi, Nobuyuki Yoshikawa

Published May 18, 2020• 2 citations
Publisher

Abstract

We analyzed the influence of 1/f noise in superconducting circuits on circuit operation using an analog circuit simulation. We devised a circuit simulation considering the 1/f noise using a conventional analog circuit simulator that can analyze the influence of thermal noises. In the circuit simulation, we used a passive filter that has a transfer function of -3 dB/oct to convert the Gaussian distributed white noise into the 1/f noise. We analyzed the gray zone characteristics of both the quantum flux parametron (QFP) and a single-flux-quantum current comparator considering both thermal and 1/f noises; the calculated gray zone width characteristics agree well with experimental results. Moreover, the influence of the 1/f noise is dominant in low operating speed regions for the QFP. These results indicate that the influence of the 1/f noise should be carefully considered to design superconducting circuits driven by a low-frequency clock.

DOI
10.1109/tasc.2020.2988871

Related papers

Investigation of the relationship between the gray zone and the clock frequency of a Josephson comparator

Taghrid Haddad, Olaf Wetzstein, Sonja Engert +2 more

The Josephson comparator is one of the fundamental building blocks of rapid single flux quantum (RSFQ) electronics. Within this circuit family it is the exclusive device which provides logical data processing. The Josephson comparator is also the basic decision element for very fast analog-to-digital converters and sampler circuits for low input power and high-bandwidth signals based on the RSFQ technique. The performance of those devices is fundamentally determined by the characteristics of the Josephson comparator. In this study the gray zone dependency on the clock frequency of a Josephson comparator is investigated by simulations concerning the influence of thermal noise. This investigation is performed for a series of operating points defined by the bias current and different noise levels defined by the operating temperature. In contrast to former investigations, we analyzed the comparator embedded in a realistic environment for output data processing. We identified a characteristic clock frequency f c for a comparator topology designed for a 1 kA cm − 2 niobium fabrication technology. The gray zone of 8 µA remains constant for clock frequencies below f c = 15 GHz and starts to increase for larger frequencies. We also found out that this characteristic frequency is independent of the intensity of thermal noise and therefore independent of temperature.

Superconductor Science and Technology•Aug 5, 2011•15 citations

Experimental Analysis of the Bias Dependent Sensitivity of a Josephson Comparator

Taghrid Haddad, Sonja Engert, Oliver Brandel +4 more

The Josephson comparator is one of the building blocks of superconductor electronics. It is used as a decision element in all analog and digital circuits. For fast high-bandwidth analog-to-digital converters as well as for digital circuits with reduced switching energy its high sensitivity is most important. Thermal noise limits its decision uncertainty. In this work we analyze the influence of the bias current on the gray zone of a Josephson comparator. Circuit simulations are compared against experimental data. The experimental analysis shows a characteristic dependence of the gray zone on the bias current. We can identify a clear minimum value. This point is related to a certain clock frequency. At low frequencies the simulated relationship between the gray zone and the bias current is in very good agreement with experimental results. The comparison confirmed the circuit model and enables to adjust the design to certain applications to realize the best trade-off between clock frequency and grey zone. The article describes the experimental validation procedure and a derived normalized dependency in detail.

IEEE Transactions on Applied Superconductivity•Jan 19, 2015•2 citations

Noise analysis of the quantum flux parametron

H.L. Ko, G.S. Lee

An analysis of the limitations imposed by thermal noise on the application of the quantum flux parametrons (QFPs) as current comparators and timing discriminators is presented. At low operational frequencies, a thermal activation approach is used, while at high frequencies a circuit simulation method is required. At frequencies greater than the Josephson junction plasma frequency, an approximate expression for the noise is given. The calculations are in good agreement with the approximations and the experimental results.>

IEEE Transactions on Applied Superconductivity•Jan 1, 1992•28 citations

Evaluation of current sensitivity of quantum flux parametron

Yuki Yamanashi, Takashi Matsushima, Naoki Takeuchi +2 more

Abstract Current sensitivity of a quantum flux parametron (QFP) was evaluated by measuring gray zone width on the basis of both circuit simulation and measurements, for superconducting sensing systems composed of a superconducting sensor array and superconducting read-out and signal processing circuits. Simulation results indicate a narrow gray zone width can be obtained by decreasing inductances comprising the QFP. Moreover, both high-sensitivity and low-power operation of the QFP can be realized by using optimized circuit parameters with an excitation current that has long rise time. A gray zone width of approximately 0.5 μ A, which is smaller than that of the Josephson current comparator based on a single flux quantum circuit, was obtained experimentally, using a trapezoidal excitation current with rise time of 50 μ s. These results indicate the QFP is promising for the read-out circuit in superconducting sensing systems, due to its high sensitivity and low power consumption.

Superconductor Science and Technology•Jul 4, 2017•14 citations

Analyzing the switching errors of RSFQ-circuits

Olaf Mielke, Thomas Ortlepp

The Rapid Single Flux Quantum electronics is a superconducting, naturally digital circuit family which is currently close to getting commercially applied.RSFQ is outstanding by its very low switching energy resulting in a very low power consumption which is the reason for a significant influence on thermal noise.For industrial applications a certain noise immunity is required which is still a challenge especially for circuits of higher complexity.In superconducting electronics resistors are the only on-chip noise sources.We analyzed the influence of each individual resistor in a toggle Flip-Flop circuit to the overall bit-error rate.The shunt resistors of comparator structures are the dominant noise sources and bias resistors have almost no influence.We analyzed in detail the types of thermal introduced switching errors of an toggle Flip-Flop which was optimized with respect to the fabrication yield.Simulation studies were accomplished to investigate the influence of circuit parameters on quality and on quantity of switching errors.By identifying and manipulating the parameters with the most significant influence on the noise susceptibility an enhanced noise immunity of the device can be achieved.The goal is to improve the robustness of RSFQ circuits against the influence of thermal noise for an specific topology by changing the circuit parameters of the device.

USB-Flash-Ausg.:#R#<br/>Information technology and electrical engineering - devices and systems, materials and technologies for the future : 54. IWK, Internationales Wissenschaftliches Kolloquium ; proceedings ; 07 - 10 September 2009 / Faculty of Electrical and Information Technology, Technische Universität Ilmenau. - Ilmenau : Verl. ISLE, 2009. - ISBN 978-3-938843-45-1•Jan 1, 2009•0 citations

Experimental Demonstration and Numerical Analysis of Microampere Gray Zone Width with Enhanced Operating Margin in Shunted Quasi-One Junction Superconducting Quantum Interference Device Comparators

Shigeyuki Miyajima, Thomas Ortlepp, Hannes Toepfer +2 more

We evaluated the relationship between the gray zone width and the operating margin for comparators composed of quasi-one-junction superconducting quantum interference devices (QOSs) with shunt resistors, which are often used as high-speed readout circuits in multiple superconductor detector systems. The gray zone width is a good measure of current sensitivity of a single-bit comparator. We numerically analyzed the gray zone width of a QOS comparator and determined the circuit parameters. The gray zone width obtained from the experiments concurred with the results of the numerical analysis and was 2–3 µA at 4.2 K in a QOS comparator composed of three Nb/AlOx/Nb junctions with critical currents of less than 90 µA. The experimentally obtained operating margin for the bias current provided to the comparator was ±15% at the bias current of around 140 µA. These results show that QOS comparators are promising for readout circuits operating up to tens of GHz and imply that gray zone width is the thermal noise in the resistors at 4.2 K.

Japanese Journal of Applied Physics•Feb 25, 2013•6 citations
We analyzed the influence of 1/f noise in superconducting circuits on circuit operation using an analog circuit simulation. We devised a circuit simulation considering the 1/f noise using a conventional analog circuit simulator that can analyze the influence of thermal noises. In the circuit simulation, we used a passive filter that has a transfer function of -3 dB/oct to convert the Gaussian distributed white noise into the 1/f noise. We analyzed the gray zone characteristics of both the quantum flux parametron (QFP) and a single-flux-quantum current comparator considering both thermal and 1/f noises; the calculated gray zone width characteristics agree well with experimental results. Moreover, the influence of the 1/f noise is dominant in low operating speed regions for the QFP. These results indicate that the influence of the 1/f noise should be carefully considered to design superconducting circuits driven by a low-frequency clock.
The Josephson comparator is one of the fundamental building blocks of rapid single flux quantum (RSFQ) electronics. Within this circuit family it is the exclusive device which provides logical data processing. The Josephson comparator is also the basic decision element for very fast analog-to-digital converters and sampler circuits for low input power and high-bandwidth signals based on the RSFQ technique. The performance of those devices is fundamentally determined by the characteristics of the Josephson comparator. In this study the gray zone dependency on the clock frequency of a Josephson comparator is investigated by simulations concerning the influence of thermal noise. This investigation is performed for a series of operating points defined by the bias current and different noise levels defined by the operating temperature. In contrast to former investigations, we analyzed the comparator embedded in a realistic environment for output data processing. We identified a characteristic clock frequency f c for a comparator topology designed for a 1 kA cm − 2 niobium fabrication technology. The gray zone of 8 µA remains constant for clock frequencies below f c = 15 GHz and starts to increase for larger frequencies. We also found out that this characteristic frequency is independent of the intensity of thermal noise and therefore independent of temperature.
The Josephson comparator is one of the building blocks of superconductor electronics. It is used as a decision element in all analog and digital circuits. For fast high-bandwidth analog-to-digital converters as well as for digital circuits with reduced switching energy its high sensitivity is most important. Thermal noise limits its decision uncertainty. In this work we analyze the influence of the bias current on the gray zone of a Josephson comparator. Circuit simulations are compared against experimental data. The experimental analysis shows a characteristic dependence of the gray zone on the bias current. We can identify a clear minimum value. This point is related to a certain clock frequency. At low frequencies the simulated relationship between the gray zone and the bias current is in very good agreement with experimental results. The comparison confirmed the circuit model and enables to adjust the design to certain applications to realize the best trade-off between clock frequency and grey zone. The article describes the experimental validation procedure and a derived normalized dependency in detail.
An analysis of the limitations imposed by thermal noise on the application of the quantum flux parametrons (QFPs) as current comparators and timing discriminators is presented. At low operational frequencies, a thermal activation approach is used, while at high frequencies a circuit simulation method is required. At frequencies greater than the Josephson junction plasma frequency, an approximate expression for the noise is given. The calculations are in good agreement with the approximations and the experimental results.>
Abstract Current sensitivity of a quantum flux parametron (QFP) was evaluated by measuring gray zone width on the basis of both circuit simulation and measurements, for superconducting sensing systems composed of a superconducting sensor array and superconducting read-out and signal processing circuits. Simulation results indicate a narrow gray zone width can be obtained by decreasing inductances comprising the QFP. Moreover, both high-sensitivity and low-power operation of the QFP can be realized by using optimized circuit parameters with an excitation current that has long rise time. A gray zone width of approximately 0.5 μ A, which is smaller than that of the Josephson current comparator based on a single flux quantum circuit, was obtained experimentally, using a trapezoidal excitation current with rise time of 50 μ s. These results indicate the QFP is promising for the read-out circuit in superconducting sensing systems, due to its high sensitivity and low power consumption.
The Rapid Single Flux Quantum electronics is a superconducting, naturally digital circuit family which is currently close to getting commercially applied.RSFQ is outstanding by its very low switching energy resulting in a very low power consumption which is the reason for a significant influence on thermal noise.For industrial applications a certain noise immunity is required which is still a challenge especially for circuits of higher complexity.In superconducting electronics resistors are the only on-chip noise sources.We analyzed the influence of each individual resistor in a toggle Flip-Flop circuit to the overall bit-error rate.The shunt resistors of comparator structures are the dominant noise sources and bias resistors have almost no influence.We analyzed in detail the types of thermal introduced switching errors of an toggle Flip-Flop which was optimized with respect to the fabrication yield.Simulation studies were accomplished to investigate the influence of circuit parameters on quality and on quantity of switching errors.By identifying and manipulating the parameters with the most significant influence on the noise susceptibility an enhanced noise immunity of the device can be achieved.The goal is to improve the robustness of RSFQ circuits against the influence of thermal noise for an specific topology by changing the circuit parameters of the device.
We evaluated the relationship between the gray zone width and the operating margin for comparators composed of quasi-one-junction superconducting quantum interference devices (QOSs) with shunt resistors, which are often used as high-speed readout circuits in multiple superconductor detector systems. The gray zone width is a good measure of current sensitivity of a single-bit comparator. We numerically analyzed the gray zone width of a QOS comparator and determined the circuit parameters. The gray zone width obtained from the experiments concurred with the results of the numerical analysis and was 2–3 µA at 4.2 K in a QOS comparator composed of three Nb/AlOx/Nb junctions with critical currents of less than 90 µA. The experimentally obtained operating margin for the bias current provided to the comparator was ±15% at the bias current of around 140 µA. These results show that QOS comparators are promising for readout circuits operating up to tens of GHz and imply that gray zone width is the thermal noise in the resistors at 4.2 K.