Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Chinese Physics B

Manipulation of superconducting qubit with direct digital synthesis*

Zhiyuan Li, Haifeng Yu, Xinsheng Tan, Shi-Ping Zhao, Yang Yu

Published Aug 2, 2019• 5 citations
Publisher

Abstract

We investigate the XY control and manipulation of the superconducting qubit state using direct digital synthesis (DDS) for the microwave pulse signal generation. The decoherence time, gate fidelity, and other qubit properties are measured and carefully characterized, and compared with the results obtained by using the traditional mixing technique for the microwave pulse generation. In particular, the qubit performance in the state manipulation with respect to the sampling rate of DDS is studied. Our results demonstrate that the present technique provides a simple and effective method for the XY control and manipulation of the superconducting qubit state. Realistic applications of the technique for the possible future scalable superconducting quantum computation are discussed.

DOI
10.1088/1674-1056/ab37f9

Related papers

High-Fidelity Control of Superconducting Qubits Using Direct Microwave Synthesis in Higher Nyquist Zones

William D. Kalfus, Diana F. Lee, Guilhem J. Ribeill +5 more

Control electronics for superconducting quantum processors have strict requirements for accurate command of the sensitive quantum states of their qubits. Hinging on the purity of ultra-phase-stable oscillators to upconvert very-low-noise baseband pulses, conventional control systems can become prohibitively complex and expensive when scaling to larger quantum devices, especially as high sampling rates become desirable for fine-grained pulse shaping. Few-gigahertz radio-frequency (RF) digital-to-analog converters (DACs) present a more economical avenue for high-fidelity control while simultaneously providing greater command over the spectrum of the synthesized signal. Modern RF DACs with extra-wide bandwidths are able to directly synthesize tones above their sampling rates, thereby keeping the system clock rate at a level compatible with modern digital logic systems while still being able to generate high-frequency pulses with arbitrary profiles. We have incorporated custom superconducting qubit control logic into off-the-shelf hardware capable of low-noise pulse synthesis up to 7.5 GHz using an RF DAC clocked at 5 GHz. Our approach enables highly linear and stable microwave synthesis over a wide bandwidth, giving rise to high-resolution control and a reduced number of required signal sources per qubit. We characterize the performance of the hardware using a five-transmon superconducting device and demonstrate consistently reduced two-qubit gate error (as low as 1.8%), which we show results from superior control chain linearity compared to traditional configurations. The exceptional flexibility and stability further establish a foundation for scalable quantum control beyond intermediate-scale devices.

arXiv:2008.02873•IEEE Transactions on Quantum Engineering•Jan 1, 2020•27 citations

Fast Microwave-free State Preparation and Measurement of Superconducting Qubits

R. Abraham, F. Amet, P. Anderson +212 more

Fast, high-fidelity, scalable state preparation and measurement is critical to the realization of a quantum computing system. The state-of-the-art methods for preparation and readout of superconducting qubits require finely tuned microwave signals and ~100 ns of measurement time, which are major obstacles to the scalability and performance of superconducting quantum computers. Here, we have demonstrated novel, microwave-free methods for both preparation and readout of superconducting qubits with >99% fidelity in only 10 ns for either operation while maintaining qubit coherence. This technology is compatible with scalable superconducting digital control systems, and using quantum flux parametrons for amplification, we demonstrated full quantum-to-digital conversion in only 15 ns, which is an order of magnitude faster than state-of-the-art microwave-based techniques.

quant-pharXiv:2609.01334•Sep 2, 2026•0 citations

Direct digital synthesis of microwave waveforms for quantum computing

James J. Raftery, Andrei Vrajitoarea, G. Zhang +3 more

Current state of the art quantum computing experiments in the microwave regime use control pulses generated by modulating microwave tones with baseband signals generated by an arbitrary waveform generator (AWG). Recent advances in digital analog conversion technology have made it possible to directly synthesize arbitrary microwave pulses with sampling rates up to 92 gigasamples per second (GS/s). These new high bandwidth AWG's could dramatically simplify the classical control chain for quantum computing experiments, enabling more advanced pulse shaping and reducing the number of components that need to be carefully calibrated. Here we use a high speed AWG to study the viability of such a simplified scheme. We characterize the AWG and perform randomized benchmarking of a superconducting qubit, achieving average single qubit gate error rates below $5\times10^{-4}$.

arXiv:1703.00942•Mar 2, 2017•15 citations

Coherence-limited digital control of a superconducting qubit using a Josephson pulse generator at 3 K

M. A. Castellanos-Beltran, A. J. Sirois, L. Howe +4 more

Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime $T_1$, coherence time $T_2^*$ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for $T_1$ and $T_2^*$, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of $0.46$% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.

quant-pharXiv:2512.07962•Applied Physics Letters•Dec 10, 2025•11 citations

AC metrology applications of the Josephson effect

Samuel P. Benz, John Biesecker, Charles J. Burroughs +10 more

The performance of programmable voltage signals that exploit the quantum behavior of superconducting Josephson junctions continues to improve and enhance measurements in metrology, communications, and quantum control. We review advances in pulse-driven digital synthesis techniques with Josephson-junction-based devices. Quantum-based synthesis of voltage waveforms has been demonstrated at frequencies up to 3 GHz and rms amplitudes up to 4 V. Josephson pulse generators have also been used to control and characterize superconducting qubits.

Applied Physics Letters•Jul 29, 2024•10 citations

Digital Readout and Control of a Superconducting Qubit

Caleb Howington

In the quest to build a fault-tolerant quantum computer, superconducting circuits based on Josephson junctions have emerged as a leading architecture. Coherence times have increased significantly over the last two decades, and processors with ∼ 50 qubits have been experimentally demonstrated. These systems traditionally utilize microwave frequency control signals, and heterodyne based detection schemes for measurement. Both of these techniques rely heavily on room temperature microwave generators, high-bandwidth lines from room temperature to millikelvin temperatures, and bulky non-reciprocal elements such as cryogenic microwave isolators. Reliance on these elements makes it impractical to scale existing devices up a single order of magnitude, let alone the 5-6 orders of magnitude needed for performing fault-tolerant quantum algorithms. Here, I present results that suggesting superconducting digital logic, namely Single Flux Quantum (SFQ) logic, can replace analog control and measurement techniques, avoiding the significant overhead involved. I describe a scheme for measuring qubits with a device known as a Josephson Photomultiplier (JPM), which crucially stores the result of a qubit measurement in a classical circulating supercurrent within the device and allows for integration with SFQ detection circuitry. This technique is experimentally demonstrated, with single-shot measurement fidelity of 92%. Two methods for accessing this measurement result are presented, one utilizing ballistic fluxons, and another utilizing flux comparison. Initial experimental results of the latter are presented. In addition, I describe a scheme for controlling qubits with sequences of digital SFQ pulses. This method is then used to control a qubit without a microwave signal generator, with results of an average single-qubit gate fidelity of around 95%. When combined, these techniques form a nearly fully digital interface to superconducting qubits, which could allow these systems to scale much more easily.

•Jan 1, 2019•0 citations
We investigate the XY control and manipulation of the superconducting qubit state using direct digital synthesis (DDS) for the microwave pulse signal generation. The decoherence time, gate fidelity, and other qubit properties are measured and carefully characterized, and compared with the results obtained by using the traditional mixing technique for the microwave pulse generation. In particular, the qubit performance in the state manipulation with respect to the sampling rate of DDS is studied. Our results demonstrate that the present technique provides a simple and effective method for the XY control and manipulation of the superconducting qubit state. Realistic applications of the technique for the possible future scalable superconducting quantum computation are discussed.
Control electronics for superconducting quantum processors have strict requirements for accurate command of the sensitive quantum states of their qubits. Hinging on the purity of ultra-phase-stable oscillators to upconvert very-low-noise baseband pulses, conventional control systems can become prohibitively complex and expensive when scaling to larger quantum devices, especially as high sampling rates become desirable for fine-grained pulse shaping. Few-gigahertz radio-frequency (RF) digital-to-analog converters (DACs) present a more economical avenue for high-fidelity control while simultaneously providing greater command over the spectrum of the synthesized signal. Modern RF DACs with extra-wide bandwidths are able to directly synthesize tones above their sampling rates, thereby keeping the system clock rate at a level compatible with modern digital logic systems while still being able to generate high-frequency pulses with arbitrary profiles. We have incorporated custom superconducting qubit control logic into off-the-shelf hardware capable of low-noise pulse synthesis up to 7.5 GHz using an RF DAC clocked at 5 GHz. Our approach enables highly linear and stable microwave synthesis over a wide bandwidth, giving rise to high-resolution control and a reduced number of required signal sources per qubit. We characterize the performance of the hardware using a five-transmon superconducting device and demonstrate consistently reduced two-qubit gate error (as low as 1.8%), which we show results from superior control chain linearity compared to traditional configurations. The exceptional flexibility and stability further establish a foundation for scalable quantum control beyond intermediate-scale devices.
Fast, high-fidelity, scalable state preparation and measurement is critical to the realization of a quantum computing system. The state-of-the-art methods for preparation and readout of superconducting qubits require finely tuned microwave signals and ~100 ns of measurement time, which are major obstacles to the scalability and performance of superconducting quantum computers. Here, we have demonstrated novel, microwave-free methods for both preparation and readout of superconducting qubits with >99% fidelity in only 10 ns for either operation while maintaining qubit coherence. This technology is compatible with scalable superconducting digital control systems, and using quantum flux parametrons for amplification, we demonstrated full quantum-to-digital conversion in only 15 ns, which is an order of magnitude faster than state-of-the-art microwave-based techniques.
Current state of the art quantum computing experiments in the microwave regime use control pulses generated by modulating microwave tones with baseband signals generated by an arbitrary waveform generator (AWG). Recent advances in digital analog conversion technology have made it possible to directly synthesize arbitrary microwave pulses with sampling rates up to 92 gigasamples per second (GS/s). These new high bandwidth AWG's could dramatically simplify the classical control chain for quantum computing experiments, enabling more advanced pulse shaping and reducing the number of components that need to be carefully calibrated. Here we use a high speed AWG to study the viability of such a simplified scheme. We characterize the AWG and perform randomized benchmarking of a superconducting qubit, achieving average single qubit gate error rates below 5×10−45\times10^{-4}5×10−4.
Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime T1T_1T1​, coherence time T2∗T_2^*T2∗​ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for T1T_1T1​ and T2∗T_2^*T2∗​, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of 0.460.460.46% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.
The performance of programmable voltage signals that exploit the quantum behavior of superconducting Josephson junctions continues to improve and enhance measurements in metrology, communications, and quantum control. We review advances in pulse-driven digital synthesis techniques with Josephson-junction-based devices. Quantum-based synthesis of voltage waveforms has been demonstrated at frequencies up to 3 GHz and rms amplitudes up to 4 V. Josephson pulse generators have also been used to control and characterize superconducting qubits.
In the quest to build a fault-tolerant quantum computer, superconducting circuits based on Josephson junctions have emerged as a leading architecture. Coherence times have increased significantly over the last two decades, and processors with ∼ 50 qubits have been experimentally demonstrated. These systems traditionally utilize microwave frequency control signals, and heterodyne based detection schemes for measurement. Both of these techniques rely heavily on room temperature microwave generators, high-bandwidth lines from room temperature to millikelvin temperatures, and bulky non-reciprocal elements such as cryogenic microwave isolators. Reliance on these elements makes it impractical to scale existing devices up a single order of magnitude, let alone the 5-6 orders of magnitude needed for performing fault-tolerant quantum algorithms. Here, I present results that suggesting superconducting digital logic, namely Single Flux Quantum (SFQ) logic, can replace analog control and measurement techniques, avoiding the significant overhead involved. I describe a scheme for measuring qubits with a device known as a Josephson Photomultiplier (JPM), which crucially stores the result of a qubit measurement in a classical circulating supercurrent within the device and allows for integration with SFQ detection circuitry. This technique is experimentally demonstrated, with single-shot measurement fidelity of 92%. Two methods for accessing this measurement result are presented, one utilizing ballistic fluxons, and another utilizing flux comparison. Initial experimental results of the latter are presented. In addition, I describe a scheme for controlling qubits with sequences of digital SFQ pulses. This method is then used to control a qubit without a microwave signal generator, with results of an average single-qubit gate fidelity of around 95%. When combined, these techniques form a nearly fully digital interface to superconducting qubits, which could allow these systems to scale much more easily.